Investigation of Different Turbulence Models Performance on High-turning Turbine Blade Loading Calculations
R
Saberi
کارشناسی ارشد، دانشکده هوافضا، دانشگاه صنعتی خواجه نصیر الدین طوسی، تهران، ایران
author
M
Fathali
استادیار، دانشکده هوافضا، دانشگاه صنعتی خواجه نصیر الدین طوسی، تهران، ایران
author
text
article
2015
per
In this research, the performances of different turbulence models for simulating flow field in turbine stator have been numerically investigated. To this end, incompressible fluid flow around a high-turning stator blade in Reynolds 2.23×105 has been simulated using FLUENT CFD software. Navier-Stokes equation is discretized on a Hybrid computational grid based on the finite volume approach. Considered turbulence models in this research are “Spalart-Allmaras”, “Standard k-ε”, “Realizable k-ε”, “RNG k-ε” , “SST k-ω” and “five-equation Reynolds-Stress Model (RSM)”. The performances of these models are evaluated by comparing the pressure coefficients obtained from numerical simulations with corresponding experimental data at four different stator regions. It has been observed that the ability of a turbulence model to predict flow field is not uniform throughout the stator blade. Moreover, all models show relatively poor performance in flow field regions with intense velocity gradients. Comparing the overall accuracy of different models, SST k-ω and RSM turbulence models show the best agreement with the experimental data.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
1
12
https://mej.aut.ac.ir/article_459_c2834362c18fb405f1d5cf538d1fb396.pdf
dx.doi.org/10.22060/mej.2015.459
Introduction of an improved Harmony Search Optimization Algorithm for investigating of Airfoil Parameterization Methods and Aerodynamics optimization
Farhad
Jalili
دانشجوی کارشناسی ارشد، دانشکده فنی و مهندسی، دانشگاه بیرجند، بیرجند، ایران
author
Majid
Malek-jafarian
استادیار، دانشکده فنی و مهندسی، دانشگاه بیرجند، بیرجند، ایران
author
َAli
Safavinejad
استادیار، دانشکده فنی و مهندسی، دانشگاه بیرجند، بیرجند، ایران
author
text
article
2015
per
Utilizing an airfoil Parameterization method is one of the essential requirements for airfoils optimization. The selection of this method plays an important role, as using an unsuitable method yields the weak results. In addition, it will impose delay on convergence of the solution. Hence, in this work, an improved Harmony Search meta-heuristic optimization algorithm has been developed for investigating three common airfoil parameterization methods (Bezier curves, Parces method and 4-digit-NACA formula) using an inverse optimization design and a non-aerodynamics objective function. The obtained results show that the Bezier curves and Parces method are more efficient than 4-digit-NACA formula. Finally, because of having few control parameters, the Parces method has been used along with an improved Harmony Search algorithm for the shape optimization of an airfoil under a viscose and turbulent flow, with the objective of maximizing lift to drag ratio. To do this, 2-dimentional compressible Navier-Stokes equations with Spalart-Allmaras turbulent method have been solved around the airfoil. The results reveal that the improved optimization algorithm is highly capable of evaluating the airfoil parameterization methods and aerodynamics optimization.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
13
31
https://mej.aut.ac.ir/article_460_e97c0f67fcbda069fe478303f9f85915.pdf
dx.doi.org/10.22060/mej.2015.460
Experimental Investigation of the Bubbly Drag Reduction in the Presence of Axial Flow in a the Couette-Taylor System
Reza
Maryami
دانشجوی دکتری، دانشکده مهندسی مکانیک ، دانشگاه یزد، یزد، ایران
author
Said
Farahat
دانشیار، دانشکده مهندسی مکانیک ، دانشگاه سیستان و بلوچستان، سیستان و بلوچستان ، ایران
author
M. H.
Shafie Mayam
استادیار، دانشکده مهندسی مکانیک ، دانشگاه سیستان و بلوچستان، سیستان و بلوچستان ، ایران
author
S. M.
JavadPoor
دانشجوی دکتری، دانشکده مهندسی مکانیک، دانشگاه سیستان و بلوچستان، سیستان و بلوچستان ، ایران
author
text
article
2015
per
Modification of frictional drag reduction due to the presence of small bubbles and axial flow is investigated experimentally using a Couette-Taylor system. Flow condition between concentric cylinders is fully turbulent and Taylor vortices are appeared into flow when rotational Reynolds number is changed from 5000 to 70000. Torque acting on rotating inner cylinder and bubble behavior are measured while air bubbles and axial flow are injected constantly from the bottom of the system into annulus gap. Pure water is used to avoid the uncertain interfacial property of bubbles and to produce nearly mono-sized bubble distributions. Bubble diameter is measured by image processing method. The result showed that in the absence of small bubbles, axial flow reduces the friction drag. Moreover, it is observed that axial flow improves positive effect of bubbles on drag reduction. In this case, a drag reduction of 28% is obtained which is decreased by increasing the rotational Reynolds number.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
33
45
https://mej.aut.ac.ir/article_461_af1ebb2780d7e9e6e089977782addaa1.pdf
dx.doi.org/10.22060/mej.2015.461
An Air Zonal Model for Predicting Air Flow, Temperature Distribution and Humidity Distribution in Buildings
M.
Ghodrati
دانشجوی کارشناسی ارشد، دانشکده فنی و مهندسی، دانشگاه تربیت مدرس، تهران، ایران
author
Aziz
Azimi
استادیار، گروه مهندسی مکانیک، دانشگاه شهید چمران، اهواز، ایران
author
Mehdi
Maerefat
دانشیار، دانشکده فنی و مهندسی، دانشگاه تربیت مدرس، تهران، ایران
author
text
article
2015
per
The design of air-conditioning systems for energy saver buildings relies on fast and accurate methods able to predict the details of the indoor environment. In this paper, it is shown that the air zonal method is able to quickly assess the indoor environment quality. The zonal method is based on energy and mass balance equations in macroscopic volumes. Zonal models use a coarse grid and balance equations, state equations, hydrostatic pressure drop equations and power law equations. The aim of this paper is to study the simulation of temperature and humidity distributions through a large horizontal opening in a room with mixed ventilation by means of air zonal method and the results are compared to Computational Fluid Dynamics (CFD) calculations and experimental data. It has been shown that for the simple rectangular geometries, the air zonal method gives reasonably an accurate air temperature and humidity results in engineering applications even for the whole year.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
47
57
https://mej.aut.ac.ir/article_462_914e17df079b901d58034596b4306cf0.pdf
dx.doi.org/10.22060/mej.2015.462
Parametric Investigation of the Role of Contributing Factors on Thermal Comfort and Inhaled Air Quality for a Room with Stratum Ventilation
G.R.
Molaeimanesh
استادیار، دانشکده مهندسی خودرو، دانشگاه علم و صنعت، تهران، ایران
author
text
article
2015
per
Stratum ventilation method is the most promising option for reducing energy consumption of ventilation systems in near future. In this method, which is currently implemented in some modern countries, the ventilation of only a stratum of indoor space in which occupants’ head and chest are located, is pursued. In the current study, 17 stratum ventilated cases with a manikin sited behind a desk and with different manikin’s sitting locations, outlet positions and contaminant source locations are numerically modeled. To investigate the effects of sitting location, outlet position, and contaminant source location on thermal comfort and inhaled air quality, a parametric study with four different evaluation indexes is performed. The results of this study can help improve the design and performance of stratum ventilation systems
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
59
67
https://mej.aut.ac.ir/article_463_fd0720c6dfcc74afa424be2444ebcc6c.pdf
dx.doi.org/10.22060/mej.2015.463
Immersed Boundary–Thermal Lattice Boltzmann Method with Sharp Interface: Heat Transfer of Non-Newtonian Fluid over a Cylinder
Amin
Amiri Delouei
دانشجوی دکتری، دانشکده مکانیک، دانشگاه صنعتی شاهرود، شاهرود، ایران
author
Mohsen
Nazari
استادیار، دانشکده مکانیک، دانشگاه صنعتی شاهرود، شاهرود، ایران
author
M.H.
Kayhani
استاد، دانشکده مکانیک، دانشگاه صنعتی شاهرود، شاهرود، ایران
author
text
article
2015
per
In the current study, the problem of heat transfer in non-Newtonian fluid flow over a cylinder has been simulated using the Immersed Boundary – thermal lattice Boltzmann method and direct forcing algorithm. The sharp interface scheme isused to transfer the values of velocity and temperature between the fluid Eulerian and boundary Lagrangian nodes. In order to consider the effects of both discrete grid and boundary forces (thermal forces), the split-forcing lattice Boltzmann method is developed for non-Newtonian power-law fluids. A simple technique for calculating the Nusselt number based on the sharp immersed boundary method is extracted. Heat transfer of different fluid regimes consist of steady and unsteady flow in wide ranges of Reynolds numbers (20<Re<80) and power-law indices (0.6<n<1.4) has been investigated. It is found that the increment of the shear-thinning and shear-thickening behavior of the fluid leads to an increase and decrease of heat transfer rate of immersed body, respectively. In future studies, the proposed algorithm will be used as a suitable method for thermal modeling of moving bodies in non-Newtonian fluids.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
69
80
https://mej.aut.ac.ir/article_464_f0327c14610b8b878150e70252963ff7.pdf
dx.doi.org/10.22060/mej.2015.464
Numerical investigation of Joule heating effects on electroosmotic flow through a microchannel with triangular cross-section
M. M.
Afsari
دانشجوی کارشناسی ارشد، ،دانشکده مهندسی، دانشگاه بیرجند، بیرجند، ایران
author
S. A.
Mirbozorgi
استادیار گروه مکانیک، دانشکده مهندسی، دانشگاه بیرجند، بیرجند، ایران
author
text
article
2015
per
In this paper, numerical investigation of Joule heating effects on the electroosmotic flow through a microchannel with the triangular cross section and constant wall temperature have been presented. The energy equation for the temperature distribution, Navier–Stokes equation for the velocity distribution and a Poisson equation for the electric potential distribution have been solved by using the finite-volume method in a system curvilinear coordinates. Thermophysical properties such as the dynamic viscosity and electric conductivity vary with temperature. The results show that by increasing the Joule number, the temperature, velocity and mass flow rate increase with constant EDL number. With constant Joule number, the increments of EDL number causes the mass flow rate to increase. Mean temperature and velocity reduced by increasing the angle between sides and base of the cross-section in the particular Joule number.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
81
90
https://mej.aut.ac.ir/article_465_2e596612932ca5dc7014c6cd6a19c65a.pdf
dx.doi.org/10.22060/mej.2015.465
The Comparison between Al2O3/water and CuO/water nanofluids experimental heat transfer performance inside triangular duct
S.
Zeinali Heris
استادیار داوشکد م ىُدسی داوشگا فردیسی مش دُ ایران
author
Zahra
Edalati
کارشىاسی ارشد داوشکد م ىُدسی داوشگا فردیسی مش دُ ایران
author
S.H.
Noie
استاد داوشکد م ىُدسی داوشگا فردیسی مش دُ ایران
author
text
article
2015
per
Experimentally and numerically investigation of triangular ducts heat transfer is very important for many heating and cooling systems because of their very low pressure drop. But/ Nevertheless , this non-circular duct has very bad heat transfer performance. In the present study, the heat transfer performance of triangular ducts using nanofluid as heat transfer media is experimentally investigated. Nanofluid (which is the stable suspension of nanoparticles inside base fluid) is a new kind of heat transfer fluid and has very good potential for the heat transfer enhancement. Two kinds of nanofluid (Al2O3/water and CuO/water) produced and injected to the experimental set up, and the Nusselt number and heat transfer coefficients of these nanofluids are determined experimentally and compared with each other. The result expressed that Cuo/water presents better heat transfer performance compared to Al2O3/water nanofluid.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
91
99
https://mej.aut.ac.ir/article_466_040e80ad1f4aa4c1ca4467e1b43aae77.pdf
dx.doi.org/10.22060/mej.2015.466
Theoretical and Experimental Analysis of Asbestos Phenolic Ablative Insulation
A.
Esmaili
دانشجوی دکتری، دانشکده مهندسی مکانیک، دانشگاه تربیت مدرس، تهران، ایران
author
S.
Naseri
کارشناسی ارشد، دانشکده مهندسی هوافضا، دانشگاه صنعتی امیرکبیر ، تهران، ایران
author
text
article
2015
per
One of the major challenges in high-speed flights is aerodynamic heating. This is why thermal protection system (TPS) is being used. One of the main components of TPS is ablative insulation. In present study, one-dimensional theoretical and experimental analysis of ablative insulations have been done. Phenolic resins with maximum thermal destruction efficiency are being used in charring ablative insulations. When an ablative insulation is exposed to heat flux, its surface gets warmer and as the destruction begins, it produced gases to go out and do cooling. Governing equations of these phenomena have been discretized by the finite difference method and have been solved transient and implicitly. Thermophysical properties have been evaluated by nominal curves and Pyrolysis constants have been obtained by / through the thermochemical reactions. Validation of numerical solution has been done by oxy-acetylene test. By increasing the time, the difference between numerical and experimental results increases. One reason for difference between results could be 1D-modeling, where all of the actual 3D energy is accumulated in one dimension in the numerical solution. Nonetheless, there is good agreement between numerical and experimental results and the average of absolute errors is 7.54%.
Amirkabir Journal of Mechanical Engineering
Amirkabir University of Technology
2008-6032
47
v.
1
no.
2015
101
109
https://mej.aut.ac.ir/article_467_093490b8c9eec409fe2e73e6604c4070.pdf
dx.doi.org/10.22060/mej.2015.467