@article { author = {Ghalambaz, M. and Jamesahar, E. and Sabour, M.}, title = {Natural Convection Heat Transfer Inside a Square Enclosure with a Flexible Fin}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {233-254}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2017.11808.5189}, abstract = {The present study aims to address the effect of the presence of a flexible fin on the natural convection heat transfer inside a square cavity. A flexible fin is placed on the left vertical wall by initial tilted angle 30o from the horizontal direction. An Arbitrary Lagrangian-Eulerian method for fluid-structure (fluid-flexible fin) interaction is utilized. Based on this method, the governing system of equations for laminar fluid and heat transfer is formulated into a non- dimensional form and then solved using the finite element method and then results accuracy evaluated against previous valid studies. The results are plotted for an enclosure containing a flexible fin as well as a solid fin in the non-dimensional time interval of 0 to 0.07 and in the Rayleigh number range of 106 to 2×107 and the fin tilted angle of -10° to +40°. The results show that the presence of a flexible fin deteriorates the heat transfer compared to a solid fin. In other words, using an insulated fin instead of a conductive fin makes different patterns for average Nusselt number curve in a range time and causes a reduction of the rate of heat transfer. Also, the presence of a flexible fin mounted on the hot wall especially affects the average Nusselt number in the areas above the fin location and induces oscillating heat transfer patterns.}, keywords = {Laminar natural convection heat transfer,Flexible fin,Fluid-Structure Interaction,Arbitrary Lagrangian-Eulerian method,Moving mesh}, title_fa = {انتقال حرارت جابجایی طبیعی درون یک محفظه بسته مربعی حاوی یک پره انعطاف‏ پذیر}, abstract_fa = {در این پژوهش اثر حضور یک پره انعطاف پذیر بر روی انتقال حرارت جابه جایی طبیعی درون یک محفظه بسته مربعی بررسی شد. یک پره انعطاف پذیر نازک با زاویه انحراف 30o نسبت به محور افقی، بر روی دیواره عمودی گرم سمت چپ، درون محفظه بسته قرار گرفته است. معادلات حاکم بر جریان آرام، انتقال حرارت سیال و تغییر شکل پره انعطاف پذیر با لحاظ نمودن برهم کنش میان جریان سیال- سازه و با بهره گیری از روش شبکه متحرک لاگرانژی- اویلری ارائه شدند و سپس به شکل بی بُعد انتقال یافتند. معادلات با استفاده از روش المان محدود حل شدند و سپس صحت نتایج در مقایسه با پژوهش های معتبر پیشین ارزیابی شد. نتایج، یک بار به همراه پره انعطاف پذیر و بار دیگر با پره صلب در بازه زمانی بی بُعد صفر تا 07 / 0، در محدود اعداد رایلی 6+ 10 تا7+ 2×10 و زوایای انحراف -10o تا +40o ، درون محفظه بسته ترسیم گردید. نتایج نشان می دهند که استفاده از پره انعطاف پذیر نسبت به پره صلب باعث کاهش میزان انتقال حرارت می گردد. از سوی دیگر، استفاده از پره عایق به جای پره رسانا، سبب بروز الگوهای متفاوتی برای عدد ناسلت متوسط در طول بازه زمانی شده و تضعیف انتقال حرارت را در پی دارد.}, keywords_fa = {جریان آرام جابه جایی طبیعی,پره انعطاف پذیر,برهم کنش سیال- سازه,روش لاگرانژی- اویلری,شبکه متحرک}, url = {https://mej.aut.ac.ir/article_952.html}, eprint = {https://mej.aut.ac.ir/article_952_4274b525caa5f69ed448bd8c5d081e14.pdf} } @article { author = {Kalteh, M. and Alipour Lalami, A.}, title = {Investigation of the Effect of Velocity Slip and Temperature Jump on the Heat Transfer of Nanofluid in a Microchannel Under Constant Heat Flux with Lattice Boltzmann Method}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {255-270}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2016.857}, abstract = {In this article, the effect of velocity slip and temperature jump on the flow and heat transfer characteristics of Al2O3 – Water nanofluid in a microchannel with insulated upper wall and constant heat flux on the lower one, is investigated using the lattice Boltzmann method. The problem is solved at Re equal to 5, for base fluid and nanofluid with 0.02 and 0.04 volume fractions, no-slip and slip conditions with 0.04 and 0.1 slip coefficients and also at 5 to 50 nm nanoparticle diameters. The results show that, in general, using the hydrophobic surfaces in addition to making a considerable reduction in wall shear stress, somewhat increases the heat transfer efficacy at uniform wall heat flux condition that can not be seen in the constant wall temperature situations. Also, it is shown that the effect of temperature jump on the average Nusselt number, is more for base fluid than the nanofluid and increases for higher slip coefficients. For nanofluid with 0.04 volume fraction, the average Nusselt number increases continuously with slip coefficient but, for base liquid, firstly it increases and then decreases.}, keywords = {Nanofluid,Microchannel,Temperature jump,Constant heat flux,Lattice Boltzmann method}, title_fa = {بررسی اثر لغزش سرعت و پرش دما بر انتقال حرارت نانوسیال در میکروکانالی تحت شار حرارتی ثابت با روش شبکه ی بولتزمن}, abstract_fa = {در این مقاله اثر لغزش سرعت و پرش دما بر مشخصه های جریان و انتقال حرارتی نانوسیال آب - آلومینا در یک میکروکانال دو بعدی که در صفحه پایین تحت شار حرارتی ثابت و در صفحه ی بالا عایق است، با روش شبکه ی بولتزمن مورد مطالعه قرار گرفته است. مساله مورد نظر در عدد رینولدز 5، برای سیال پایه و نانو سیال با کسر حجمی 02 / 0 و 04 / 0 در شرایط عدم لغزش و در ضرایب لغزش 04 / 0 و 1/ 0 و نیز در قطر های نانوذرات 5 تا 50 نانومتر بررسی شده است. نتایج نشان داد که به طور کلی استفاده از سطوح آبگریز ضمن کاهش محسوس تنش برشی دیواره، در شرایط شار حرارتی ثابت بر خلاف شرایط دما ثابت نه تنها باعث کاهش بازدهی انتقال حرارتی میکروکانال نمی شود، بلکه تا حدودی بازدهی آن را افزایش می دهد. همچنین مشخص شد که اثر پرش دمایی بر عدد ناسلت میانگین، در سیال پایه بیشتر از نانوسیال است و با افزایش ضریب لغزش بیشتر می شود. بطوریکه در نانو سیال با کسر حجمی 04 / 0، با افزایش ضریب لغزش بی بعد، عدد ناسلت میانگین به صورت پیوسته افزایش پیدا می کند ولی در سیال پایه این روند ابتدا صعودی و سپس نزولی است.}, keywords_fa = {نانوسیال,میکروکانال,پرش دما,شار حرارتی ثابت,روش شبکه ی بولتزمن}, url = {https://mej.aut.ac.ir/article_857.html}, eprint = {https://mej.aut.ac.ir/article_857_9688bff9ed2c122d6867cf8f6e25c367.pdf} } @article { author = {Rosta Abkenar, A. and امانی فرد, نیما and Mohhades Deylami, H. and Dolati, F.}, title = {Experimental Investigation of Flow and Heat Transfer in a Smooth Channel Affected by Vortex Generator with a Punched Hole}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {271-284}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2016.770}, abstract = {Heat transfer and hydraulic performance for flow in a rectangular channel with LVGs (longitudinal vortex generators) are experimentally investigated using the different shape of LVGs. Firstly, a precise and reliable experimental setup was designed and fabricated to generate a constant heat flux boundary condition. In order to analyze the effect of shaped LVGs, three different of the rectangular, trapezoidal and delta winglet pair vortex generators with and without punched holes on the flow field and heat transfer characteristics at the different attack angle of 15º, 30º, 45º and 60º with a small thickness has been studied. Effects of the number of punched holes were evaluated by using dimensionless numbers, friction coefficient ratio (f/f0), Nusselt number ratio (Nu/Nu0) and overall performance ((Nu/Nu0)/(f/f0)). According to the experimental results, the rectangular winglet pair without punched holes vortex generator has the highest values of friction factor ratio and increased with bigger attack angle. The friction factor decreased and heat transfer and also overall performance increased with implementing of perforated rectangular, trapezoidal and delta winglet pair in the channel but in the case of implementing trapezoidal vortex generator with two punched holes heat transfer is a little more than the vortex generator with three punched holes.}, keywords = {Heat transfer enhancement,Vortex generator,Smooth channel,Experimental investigation}, title_fa = {تحلیل تجربی میدان جریان و انتقال حرارت در یک کانال مسطح تحت تاثیر مولد گردابه سوراخ‌دار}, abstract_fa = {انتقال حرارت و عملکرد هیدرودینامیکی برای جریان در داخل کانال مستطیلی در حضور مولد گردابه به صورت تجربی با استفاده از شکل های مختلف مولد گردابه مورد مطالعه قرار گرفته است. در ابتدا تجهیزات آزمایشگاهی دقیق و مطمئن به منظور ایجاد شرایط مرزی شار حرارتی ثابت طراحی و ساخته شده است. به منظور بررسی تاثیر شکل مولد گردابه طولی، از سه نوع جفت مولد گردابه مستطیلی، ذوزنقه­ای و مثلثی در شرایط سوراخدار و بدون سوراخ استفاده شده و تاثیر آنها بر مشخصات جریان سیال و انتقال حرارت در زوایای حمله مختلف 15 ، 30 ، 45 و 60 درجه با ضخامت ناچیز مورد مطالعه قرار گرفته است.اثرات تعداد سوراخ با استفاده از پارامترهای بی بعد نسبت ضریب اصطکاک ( f/f0)، نسبت عدد ناسلت (Nu/Nu0) و عملکرد کلی ((Nu/Nu0) /( f/f0  )) مورد ارزیابی قرار گرفته است. بر طبق نتایج تجربی جفت بالچه مولد گردابه مستطیلی بدون سوراخ بیشترین نسبت ضریب اصطکاک را دارد و با افزایش زاویه حمله این نسبت افزایش می یابد. نتایج نشان می­دهد که با ایجاد سوراخ در جفت بالچه های مولد گردابه مستطیلی، ذوزنق های و مثلثی ضریب اصطکاک کاهش و انتقال حرارت و ضریب عملکرد کلی افزایش یافته است. اما در حالت بکارگیری مولد گردابه ذوزنق های با دو سوراخ، انتقال حرارت کمی بیشتر نسبت به حالت مولد گردابه سه سوراخ افزایش یافته است.}, keywords_fa = {افزایش انتقال حرارت,مولد گردابه,کانال مسطح,تحلیل تجربی}, url = {https://mej.aut.ac.ir/article_770.html}, eprint = {https://mej.aut.ac.ir/article_770_4a8caacbd97869ab51ad08573fe60123.pdf} } @article { author = {M. Heidari, M. and Rezazadeh, M. and Nasiri, M.}, title = {Analytical Solution of Heat Transfer in LaserIrradiated Skin Tissue with Surface Heat Convection Using Dual Phase Lag Model}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {285-294}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2017.11638.5147}, abstract = {The temperature distribution in the laser-irradiated biological tissue is investigated considering heat convection. The first- and the second-degree burn times are predicted using estimation of thermal damage. A non-Fourier equation of bio-heat transfer based on dual phase lag model is employed. The transport behavior of laser light in the tissue is regarded as highly absorbed and effects of the phase lag times on thermal response and thermal damage are explored considering different heat convection coefficients. The Laplace transform with discretization technique and also using boundary conditions, a set of algebraic equations in Laplace domain is generated which are solved by numerical Laplace inverse transform. The results show that the highly absorbed laser light in the tissue plays an important role in the burned skin time. Also, convective heat transfer boundary condition on the surface provides different results, even by considering the natural convection on the surface, and the first- and the second-degree burns are postponed at least 0.02 second.}, keywords = {Skin tissue,Convection heat transfer,Thermal damage,Dual phase lag model,Numerical inverse Laplace transform}, title_fa = {حل تحلیلی انتقال حرارت درون بافت پوست تحت تابش لیزر به همراه انتقال حرارت جابجایی با استفاده از مدل تاخیر فاز دوگانه}, abstract_fa = {توزیع دما در بافت پوست در اثر تابش نور لیزر به همراه انتقال حرارت جابه جایی روی سطح پوست، بررسی می گردد.پی شبینی زمان سوختگی درجه اول و دوم با استفاده از تخمین آسیب حرارتی به بافت بدست می آید. از معادله انتقال حرارت زیستی با مدل تأخیر فاز دوگانه، که یک مدل غیر فوریه است، استفاده می شود. تابش لیزر روی بافت به صورت به شدت جذب شونده در نظر گرفته شده و تأثیر تأخیر فاز بر روی توزیع دما و عمق نفوذ جبهه ی موج حرارتی با در نظر گرفتن ضرایب انتقال حرارت جابه جایی متفاوت، بررسی شده است. با استفاده از تبدیل لاپلاس به همراه روش گسسته سازی و استفاده از شرایط مرزی، یک دستگاه معادله جبری در حوزه ی لاپلاس به دست آمده و با استفاده از لاپلاس معکوس عددی حل شده است. نتایج نشان می دهد که تابش لیزر به شدت جذب شونده، پارامتری تعیین کننده در مدت زمان سوختگی در بافت پوست می باشد. همچنین افزایش ضریب انتقال حرارت جابه جایی، تأثیر چشمگیری بر نتایج دارد، به گونه-ای که با در نظر گرفتن جابه جایی طبیعی روی سطح، زمان های سوختگی درجه اول و درجه دوم، حداقل 02 / 0 ثانیه به تعویق می افتد.}, keywords_fa = {بافت پوست,انتقال حرارت جابجایی,آسیب حرارتی,مدل تأخیر فاز دوگانه,لاپلاس معکوس عددی}, url = {https://mej.aut.ac.ir/article_950.html}, eprint = {https://mej.aut.ac.ir/article_950_6c577481bf6df89410e1a034cd033f19.pdf} } @article { author = {Payan, S. and Azimifar, A.}, title = {Minimization of Rate of Heat Transfer from Rectangular Cavities with Free Convection in Various Aspect Ratios for Finding Characteristics of an Array of Adiabatic Thin Fins by PSO Algorithm}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {295-308}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2017.11795.5185}, abstract = {In the present paper, the calculation of the optimum characteristics of thin fins attached to the hot wall in closed cavities with different aspect ratios has been investigated. Free convection is predominant in the cavity. The equations of continuity, momentum, and energy are discretized by means of finite volume method and the equations will be solved by a SIMPLER algorithm. The fins are connected to the hot wall and Particle Swarm algorithm is used to optimize the location and the length of fins. In order to model fins with high heat transfer, the dimensionless diffusion coefficients of momentum and energy equations are set equal to infinity and for the modeling of insulator fins, these coefficients are considered infinite and very small, respectively. The aim is to find the optimum characteristics of the array of fins attached to the hot wall in the rectangular cavities in such a way that the heat transfer from the cold wall is minimized. The results of particle swarm optimization algorithm are compared with the reference amounts. Results show that the particle swarm optimization algorithm is capable to find the optimum characteristics of an array of fins that is not calculated by the other methods, until now. The obtained results showed that with the increase of aspect ratio, the increase of the number of fins (increase in the number of variables), the particle swarm optimization algorithm might not have the needed ability to find the general optimum. This issue was studied by some numerical tests. Therefore, it was concluded that by decreasing the number of variables (Fixed location) and finding only the length of each fin, and also by increasing the number of particles in the sample space, the accuracy of the algorithm can be increased.}, keywords = {Natural convection,Particle swarm algorithm,Adiabatic thin fins,Aspect ratios}, title_fa = {کمینه‌سازی میزان انتقال حرارت از محفظه های مستطیلی با جابجایی آزاد در نسبت های منظری مختلف با یافتن مشخصات آرایه‌ای ازپره های نازک عایق به وسیله الگوریتم کوچ پرندگان}, abstract_fa = {در این مقاله محاسبه مشخصات بهینه پره های نازک متصل به دیوار گرم در محفظه­های بسته با جابه­جایی آزاد در نسبت­های منظری مختلف مورد بررسی قرار گرفته است. معادلات پیوستگی، ممنتوم و انرژی به وسیله روش حجم محدود، گسسته می شوند و معادلات به وسیله الگوریتم سیمپلر حل می شوند. پر هها روی دیوار گرم متصل می شوند و از الگوریتم بهینه سازی کوچ پرندگان برای بهین هسازی مکان و طول پره ها استفاده شده است. برای مدل سازی پره های با هدایت حرارتی بالا، ضرایب بدون بعد دیفیوژن معادلات ممنتوم و انرژی بی نهایت، و برای مدل سازی پره های عایق ضرایب دیفیوژن معادلات ممنتوم و انرژی به ترتیب بی نهایت و بسیار کوچک قرار داده شده است. هدف، یافتن مشخصات بهینه آرایه پره های متصل شده به دیوار گرم محفظه های مستطیلی است به نحوی که انتقال حرارت از دیوار سرد کمینه شود. برای این کار نتایج الگوریتم کوچ پرندگان با مقادیر مرجع مقایسه شده است. نتایج نشان می دهد که الگوریتم کوچ پرندگان قادر به پیدا کردن مشخصات بهینه آرای های از پره ها است که تا به حال با استفاده از روش های دیگر محاسبه نشده است. نتایج به دست آمده نشان داد که با افزایش نسبت منظری و افزایش تعداد پره ها )افزایش تعداد متغیرها( ممکن است الگوریتم کوچ پرندگان توانایی لازم جهت یافتن بهینه کلی را نداشته باشد. این موضوع با چند تست عددی مورد بررسی قرار گرفت. به این ترتیب با کاهش تعداد متغیرها )ثابت نگه داشتن مکان( و یافتن تنها طول هر یک از پره ها و همچنین افزایش تعداد ذرات در فضای نمونه مشخص شد دقت الگوریتم را می توان افزایش داد.}, keywords_fa = {جابجایی آزاد,الگوریتم کوچ پرندگان,پره‌های نازک عایق,نسبت های منظری}, url = {https://mej.aut.ac.ir/article_944.html}, eprint = {https://mej.aut.ac.ir/article_944_cb893ea18cb5a1ac0a164f70a2239a60.pdf} } @article { author = {Sheikhzadeh, G.A. and Sadripour, S. and Mollamahdi, M.}, title = {Numerical Study of the Effects of Speed and Place of Ceiling Fans on Thermal Comfort and Reducing Energy in Office Buildings}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {309-326}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2017.11849.5200}, abstract = {The main aim of the present study is to investigate the effects of speed and place of ceiling fans on thermal comfort parameters (predicted mean vote and predicted percentage of dissatisfied) and energy expenses in two different office rooms with a certain geometry in winter using district heating system. In all of the models, the regime of a flow is turbulent and governing equations are solved by finite volume method and SIMPLE algorithm. Based on the results, using ceiling fans in winter (heating system) has a considerable influence on the improvement of buildings thermal comfort and reducing consumption of energy. By using ceiling fans the effective temperature of room increases and therefore radiator energy consumption decreases. Furthermore, the results show that the location of ceiling fan does not have any effect on room effective temperature and residents’ thermal comfort. According to the results, predicted mean vote and predicted percentage of dissatisfied parameters improve by turning ceiling fans on and increasing fan normal air velocity. But, the operation of fan leads to cooling system after a certain velocity and it is not acceptable for the heating system. Finally, the CF.A case with p(x)=1.0 m, V=0.2 m/s and Tradiator=51oC, and CF.B.1 case with p(x)=2.5 m, V=0.27 m/s and Tradiator=37oC, by providing thermal comfort conditions and reducing consumption of energy about 58% and 73%, respectively are reported as optimal cases. }, keywords = {Place of ceiling fan,heat transfer,Turbulent flow,Thermal comfort,Reducing consumption of energy}, title_fa = {بررسی عددی تأثیر سرعت و مکان قرارگیری فن‌سقفی بر آسایش‌حرارتی و کاهش مصرف انرژی در ساختمان‌های اداری}, abstract_fa = {هدف از مطالعه حاضر بررسی عددی تأثیر سرعت و مکان قرارگیری فن سقفی بر پارامترهای آسایش حرارتی و مصرف انرژی در دو نمونه اتاق اداری متفاوت با ابعاد مشخص در فصل زمستان با سیستم گرمایش متمرکز است. در تمامی مدل ها رژیم جریان آشفته بوده و از مدل k-ε برای مد لسازی آشفتگی استفاده شده است. بر اساس نتایج، استفاده از فن سقفی، بدون درنظرگرفتن مکان آن در یک ارتفاع مشخص، باعث کاهش مصرف انرژی می شود. با روشن کردن فن و افزایش سرعت عمودی آن، وضعیت شاخص های میانگین آراء افراد نسبت به شرایط گرمایی محیط (PMV   ) و درصد نارضایتی افراد نسبت به شرایط گرمایی محیط (  PPD  ) بهبود می یابد؛ اما از جایی به بعد کارکرد فن به سمت خنک کاری پیش رفته و دیگر برای سیستم گرمایش مناسب نیست. همچنین نتایج نشان می دهند که شاخص های آسایش حرارتی PMV و PPD تنها شرط لازم برای تأمین آسایش حرارتی انسان نیستند و شرط کافی بررسی جداگانه پارامترهای پنج گانه تشکیل دهنده شرایط آسایش حرارتی است. در پایان حالت های CF.A با p(x)=1m ، سرعت عمودی هوای فن 0/2m/s و دمای رادیاتور 51°C و CF.B.1 با m p(x)=2.5m ، سرعت عمودی هوای فن 0/27m/s و دمای رادیاتور 37°C ، با تأمین شرایط آسایش حرارتی و کاهش میزان مصرف انرژی به ترتیب در حدود 37 % و 48 % ، به عنوان مدل های بهینه در کار حاضر معرفی شده است.}, keywords_fa = {مکان قرارگیری فن سقفی,انتقال‌حرارت,جریان آشفته,آسایش حرارتی,صرفه‌جویی انرژی}, url = {https://mej.aut.ac.ir/article_981.html}, eprint = {https://mej.aut.ac.ir/article_981_503b31e121aa48abaf9b70a836c5bde0.pdf} } @article { author = {Assari, M. R. and Alipoor, A. and Nasiri, R.}, title = {Experimental Investigation of Using Phase Change Materials in Heating System of a Solar Greenhouse}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {327-336}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2016.684}, abstract = {The use of solar greenhouses has increased manifold over the last two decades and this is the main reason for thermal systems development in greenhouses. Most of the energy sources are not reliable because of the environmental problems and continuous climb in energy prices, thus using renewable and pure energies such as solar energy in the thermal systems is very important. In this paper, the use of phase change materials in the heating system of a model solar greenhouse in Dezful is analyzed and discussed experimentally. A model greenhouse with a ground area of 3 m2 has been coupled with a heating system that consists of two flat collectors and a water store that contained 18 kg paraffin wax (latent heat 190 kJ/kg and melting point 55ºC) as phase change material. Temperature variations of soil, greenhouse, and ambient were evaluated to indicate the thermal performance of this energy storage system. Results of this study indicated that the maximum average temperature of a store during energy storage is 67ºC . Over the night in the heat dissipation cycle, the rate of heat transfer and the temperature difference between inlet and outlet of the store is higher in earlier hours in comparison with later hours due to the high-temperature difference between store and greenhouse. The minimum night time temperature of greenhouse rose by 3ºC and nighttime greenhouse average temperature increased by 4ºC. Furthermore, a 6-8ºC increased in temperatures of soil in different depth was achieved.}, keywords = {Solar greenhouse,Thermal systems,Phase change material,Latent heat}, title_fa = {بررسی تجربی تاثیر استفاده از مواد تغییر فاز دهنده در سیستم گرمایشی یک گلخانه خورشیدی}, abstract_fa = {در این مقاله به بررسی تجربی تأثیر استفاده از ماده تغییر فاز دهنده در سیستم گرمایشی یک گلخانه خورشیدی آزمایشی ساخته شده در دزفول پرداخته شده است. پس از ساخت گلخانه ای به مساحت 3 متر مربع، این گلخانه به یک سیستم گرمایشی شامل یک مخزن آب حاوی 18 کیلوگرم پارافین واکس با دمای ذوب 55ºC و گرمای نهان ذوب 190kJ/kg و دو عدد کلکتور صفحه تخت تجهیز شده است. به منظور بررسی میزان تأثیر استفاده از این روش ذخیره سازی انرژی، تغییرات دمایی خاک بستر گلخانه، داخل گلخانه و همچنین محیط پیرامون آن مورد بررسی قرار گرفته است. نتایج به دست آمده نشان داد که دمای متوسط مخزن هنگام ذخیره ی انرژی به مقدار بیشینه 67ºC رسیده است. شب هنگام در طی بازیافت انرژی از مخزن، در ساعات ابتدایی به علت اختلاف دمای زیاد مخزن و گلخانه، نرخ انتقال حرارت و لذا اختلاف دمای ورودی و خروجی مخزن نسبت به ساعات انتهایی بیشتر بوده و همچنین نرخ کاهش دمای مخزن بیشتر است. کمینه دمای شبانه ی گلخانه 3ºC افزایش یافته و حدود 4ºC افزایش برای متوسط دمای شبانه حاصل شده است. همچنین 6 تا 8 درجه سانتیگراد افزایش دما در لایه های مختلف خاک حاصل شد.}, keywords_fa = {گلخانه خورشیدی,سیستم‌های حرارتی,ماده تغییر فاز دهنده,گرمای نهان}, url = {https://mej.aut.ac.ir/article_684.html}, eprint = {https://mej.aut.ac.ir/article_684_13d7144f2bb52b717e8c50d7696b7549.pdf} } @article { author = {Saeedi, A. and Khadem, J. and Raznahan, H.}, title = {Study the Effects of Uniform Magnetic Fields and Pressures on the Concentration of Main Species of Methane Combustion}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {337-346}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2017.12194.5279}, abstract = {The effects of magnetic fields on combustion to control and optimize the flame deformation and the flame brightness is a well-known fact. The kinetics and equilibrium properties of chemical reactions of combustion are influenced by the magnetic force exerted on paramagnetic species. In this study, the numerical consideration of the effects of the uniform magnetic fields on one stage methane combustion reaction has been taken. With respect to this fact that NO, OH, and O2 are paramagnetic species and other species and methane have diamagnetic behavior, the effects of the uniform magnetic field at different pressures on 10 methane combustion main product species are studied by minimizing the Gibbs free energy. The results show that the uniform magnetic field at 1 atm pressure has considerable effects on paramagnetic species and their production is influenced dramatically. Also, the role of uniform magnetic fields on product species decreases by increasing the pressure. The results also indicate that uniform magnetic fields decreases the mole fraction of NO simultaneously with the increase in the temperature. Furthermore, applying uniform magnetic field and increasing the pressure reduce NO and CO pollutants and increase the temperature.}, keywords = {Uniform magnetic field,Combustion,Methane,Chemical species,Pollutants}, title_fa = {مطالعه تغییرات غلظت گونه‏های اصلی احتراق متان در اثر فشار و میدان مغناطیسی یکنواخت}, abstract_fa = {تأثیر میدان های مغناطیسی بر احتراق جهت کنترل و بهینه سازی و حتی تغییر شکل و درخشندگی شعله موضوع شناخته شده ای است. نیروی حجمی مغناطیسی وارد بر گونه های مواد پارامغناطیس باعث تغییر رفتار طبیعی آن­ها شده و بر سینتیک و رفتار تعادلی واکنش­های شیمیایی احتراق نیز مؤثر است. در تحقیق حاضر بررسی عددی تأثیر میدان مغناطیسی یکنواخت بر واکنش یک مرحله ای احتراق متان انجام شده است. با توجه به اینکه در بین گونه­های تولید شده، OH ،NO وO2 به عنوان ماده پارامغناطیس و سایر گونه­های احتراق و متان دارای رفتار دیامغناطیس هستند، اثر اعمال میدان مغناطیسی یکنواخت در فشارهای مختلف بر 10 گونه تولید شده در فرآیند احتراق متان با کمینه سازی انرژی آزاد گیبس ارزیابی گردیده است. نتایج نشان می­دهد اثر میدان مغناطیسی یکنواخت در فشار یک اتمسفر بر گونه­های تولید شده پارامغناطیس در مقایسه با سایر گونه­ها قابل توجه تر بوده و برای تمام گونه­ها تأثیر میدان مغناطیسی یکنواخت با افزایش فشار کاهش می یابد. همچنین می­توان به کمک میدان مغناطیسی یکنواخت، تولید آلاینده NO را همزمان با افزایش دما کاهش داد. علاوه بر این با اعمال میدان مغناطیسی یکنواخت و افزایش فشار می­توان کاهش آلاینده­هایNO وCO را به طور همزمان با افزایش دما ایجاد نمود.}, keywords_fa = {میدان مغناطیسی یکنواخت,احتراق,گونه‏ های شیمیایی}, url = {https://mej.aut.ac.ir/article_982.html}, eprint = {https://mej.aut.ac.ir/article_982_f2c8f0e415cec19f9d0cbec1043a2d01.pdf} } @article { author = {Nazari, M. and Maleki-Delarestaghi1, S. and Shakeri, A.}, title = {Experimental Investigation of the Forced Convection Heat Transfer of Nanofluids in Curved Tubes}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {50}, number = {2}, pages = {347-358}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2017.12450.5340}, abstract = {In this paper, the forced convective heat transfer of Alumina/water nanofluid is experimentally investigated in uniform-temperature curved tubes in the range of 0