@article { author = {hosseini baghdad abadi, seyyed mehdi and Zirak, Saadat and Rajabi Zargarabadi, Mehran}, title = {Numerical Investigation of the Effect of Coolant Injection Angle on the Pulsed Film Cooling Effectiveness of Square Wave Flow on Flat Plate}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {52}, number = {6}, pages = {1641-1658}, year = {2018}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2018.14746.5928}, abstract = {The effect of the angle of injection on the film cooling effectiveness with square wave pulsation is investigated at various frequencies. Four angles of injection are selected at 20, 25, 30 and 35 degrees. Film cooling is used to cool turbine blades and extend the life of blade. The pulsed flow is investigated at three frequencies of 2, 50 and 500 Hz. Finite volume method is used to solve the flow governing equations. The shear stress transport k-ω model is used to model the turbulence. The obtained results showed that the injection angle of 20 to 25 degrees had the most film cooling effectiveness for all frequencies. In higher frequency, 500 Hz, it is observed an increase in the effectiveness of the film cooling in close distances after the injection holes. At far distances, the lower frequency, 2 Hz, produces the most effectiveness. The largest difference in centerline effectiveness is achieved at 500 Hz for hole angles of 20 to 35 degrees with a value of 64.3%. This value is 98.9% for lateral effectiveness. As the frequency increases, the cooling mass flow interruptions are reduced, and as a result, the instantaneous effectiveness shows a slower variation than the lower frequencies. The blowing ratio of 0.5 had the most value in comparison with the blowing ratio of 0.75 and 1 in all angles and frequencies. The maximum difference in effectiveness is 187.4% for blowing ratio of 0.5, in comparison with the other two blowing ratios.}, keywords = {Pulse film cooling؛ square wave flow؛ angle of injection؛ Shear stress transport k-ω turbu- lence model,Frequency}, title_fa = {بررسی عددی تاثیر زاویه سوراخ تزریق خنک کننده بر اثربخشی خنک کاری لایه ای جریان نوسانی موج مربعی صفحه تخت}, abstract_fa = {در این مقاله اثر تغییر زاویه تزریق بر اثربخشی خنک­کاری لایهای صفحه تخت با نوسان موج مربعی در فرکانس­های مختلف بررسی می­شود. خنک­کاری لایه­ای برای سرد کردن پره­های توربین و افزایش عمر پره استفاده می­شود. چهار زاویه تزریق 20 ،25 ،30 و 35 درجه انتخاب شده­اند. جریان نوسانی در سه فرکانس 2 ،50 و 500 هرتز و سیکل کاری 0/5 مورد بررسی قرار می­گیرد. از روش حجم محدود برای حل معادلات جریان استفاده گردید. از مدل انتقال تنش برشی کی-امگا جهت مدل­سازی آشفتگی استفاده گردید. نتایج نشان داد زاویه تزریق بین 20 تا 25 درجه در سه فرکانس مورد بررسی بیشترین اثربخشی خنک­کاری لایه­ای خط مرکزی و جانبی را به خصوص در نواحی دور از لبه سوراخ تزریق داشت. فرکانسهای باالتر )500 هرتز( افزایش اثربخشی خنک کاری لایه ای در فواصل ابتدایی پایین دست سوراخ را به­دنبال دارد. در فواصل دوردست، فرکانس پایین­تر )2 هرتز( بیشترین اثربخشی را داشت. بیشترین تفاوت اثربخشی خط مرکزی در فرکانس 500 هرتز و بین زاویه 20 و 35 درجه به دست آمد و برابر 64/3 %بود. این مقدار برای اثربخشی جانبی 98/9 %بود. نسبت دمش 0/5در مقایسه با نسبت دمش0/75 و 1 در تمامی زوایا و فرکانس­ها بیشترین اثربخشی را داشت. حداکثر تفاوت مقدار اثربخشی در نسبت دمش 5/0 در مقایسه با دو نسبت دمش دیگر برابر 187/4 %بود.}, keywords_fa = {خنک کاری لایه ای نوسانی,جریان موج مربعی,زاویه تزریق,مدل توربولانسی SST k-ω,فرکانس}, url = {https://mej.aut.ac.ir/article_3201.html}, eprint = {https://mej.aut.ac.ir/article_3201_15a77df5df965b565d78150e697a89fd.pdf} }