@article { author = {Soltani, ali and shakeri, mohsen and nourouzi, salman and Jamshidi, HAMED}, title = {Effect of friction stir welding parameters on mechanical properties of aluminum alloy to austenitic stainless steel lap joint}, journal = {Amirkabir Journal of Mechanical Engineering}, volume = {46}, number = {2}, pages = {35-43}, year = {2015}, publisher = {Amirkabir University of Technology}, issn = {2008-6032}, eissn = {2476-3446}, doi = {10.22060/mej.2015.348}, abstract = {Friction stir welding is a solid state welding processes due to the low temperature in the welding zone, prevent formation of defect that can occur during fusion welding. In this paper, the effects of three important parameters of rotational speed, welding speed and tool tilt angle on mechanical properties lap joint of aluminum alloy to austenitic stainless steel have been studied. The results showed that higher increasing the rotational speed or decreasing the welding speed can be cause the creation of defects such as created flash around the weld zone, cavity and sheet thinning defect which will strongly affect on the mechanical properties of the joint, So that maximum fracture load was obtained 7750N in the rotational and welding speed,1000rpm and 80mm/min, respectively which the rotational speed to 2000rpm led to reduce the fracture load of joint to 3350N. It also became clear that strength of the joint increases and then decreases with increasing tool tilt angle. Therefore, that with increases tool tilt angle from 1.5 to 2.5 degree, fracture strength reduce from 7750N to 4180N. Which due to increase of the heat input, create flash around the weld zone reducing the volume of material under the tool shoulder, and finally the formation of defects in the joint.}, keywords = {LAP JOINT,ALUMINUM ALLOY,STAINLESS STEEL,Friction Stir Welding,TILT ANGLE}, title_fa = {تاثیر پارامترهای جوشکاری اصطکاکی اغتشاشی بر خواص مکانیکی اتصال لبه رویهم آلیاژ آلومینیم به فولاد زنگ نزن آستنیتی}, abstract_fa = {جوشکاری اصطکاکی اغتشاشی یکی از فرآیندهای جوشکاری در حالت جامد است که بدلیل دمای پایین در موضع جوش مانع ایجاد عیوبی می شود که در جوشکاری ذوبی اتفاق می افتد. در این مقاله اثرات سه پارامتر مهم سرعت دورانی، سرعت پیشروی و زاویه انحراف ابزار بر استحکام اتصال لبه رویهم آلیاژ آلومینیم به فولاد زنگ نزن آستنیتی مورد بررسی قرار گرفته است. نتایج نشان می دهد که افزایش بیش از حد سرعت دورانی یا کاهش سرعت پیشروی می تواند باعث پدید آمدن عیوبی همچون تشکیل پلیسه، حفرات و کاهش ضخامت موثر ورق در ناحیه اتصال شود که خواص مکانیکی اتصال را به شدت تحت تاثیر قرار خواهد داد، بطوریکه حداکثر نیروی شکست در سرعت دورانی 1000 دور بر دقیقه و سرعت پیشروی 80 میلیمتر بر دقیقه، N7750 بوده که با افزایش سرعت دورانی به 2000 دور بر دقیقه به N3350 کاهش می یابد. همچنین مشخص شد که با افزایش زاویه انحراف، استحکام اتصال ابتدا افزایش و سپس کاهش می یابد بطوریکه با افزایش زاویه انحراف از 5/1 به 5/2 درجه، نیروی شکست از N7750 بهN4180 کاهش می یابد که از جمله علل آن می تواند افزایش حرارت ورودی، ایجاد پلیسه وکاهش حجم مواد در زیر شانه ابزار و درنهایت شکل گیری عیوب در ناحیه اتصال باشد.}, keywords_fa = {اتصال لبه رویهم,آلیاژ آلومینیم,فولاد زنگ نزن,جوشکاری اصطکاکی اغتشاشی,زاویه انحراف}, url = {https://mej.aut.ac.ir/article_348.html}, eprint = {https://mej.aut.ac.ir/article_348_ba9f1d42da5348cd244fc8bcbc696a1e.pdf} }