ORIGINAL_ARTICLE
بررسی رفتار ارتعاشی و عیب یابی تیر کوتاه یکسرگیردار ترک دار تحت نیروی محوری
در این پژوهش رفتار ارتعاشی تیر کوتاه یکسرگیردار ترک دار تحت نیروی محوری مورد بررسی قرار گرفته و روشی برای عیب یابی آن بر اساس آنالیز ارتعاشی ارائه شده است. بدین منظور اثرات نیروی محوری، تغییر شکل برشی و اینرسی دورانی در نظر گرفته شده است. مقطع معیوب به صورت یک جزء انعطاف پذیر در نظر گرفته شده است که تیر را به دو قسمت تقسیم می کند. ترک بصورت فنر پیچشی مدل شده است که سفتی معادل آن از تئوری مکانیک شکست به دست می آید. پس از استخراج معادلات حاکم بر رفتار ارتعاشی تیر ترک دار، مشخصه های ارتعاشی تیر معیوب به روش مستقیم استخراج شده است. به منظور عیب یابی، به روش معکوس از مشخصه های ارتعاشی استفاده شده، و موقعیت و عمق ترک تعیین می شود. در نهایت اثرات نیروی محوری و پارامترهای ترک بر پاسخ ارتعاشی بررسی می شود. صحت نتایج به دست آمده با استفاده از نتایج تئوری و تجربی ارائه شده در ادبیات فن به اثبات رسیده است
https://mej.aut.ac.ir/article_599_2c85ce2189af8c1f285eb9e514360dfe.pdf
2016-01-21
1
12
10.22060/mej.2016.599
تیر ترک دار
نیروی محوری
تیر تیموشنکو
عیب یابی
موسی
رضائی
m_rezaee@tabrizu.ac.ir
1
دانشیار، دانشکده فنی مهندسی مکانیک، دانشگاه تبریز
LEAD_AUTHOR
حسین
جوادیان
hossein_javadian@yahoo.com
2
دانشجوی کارشناسی ارشد، دانشکده فنی مهندسی مکانیک، دانشگاه تبریز
AUTHOR
وحید
عرب ملکی
vahid_maleki@ymail.com
3
دانشجوی دکتری، دانشکده فنی مهندسی مکانیک، دانشگاه تبریز
AUTHOR
[1] S. W. Dobeling, C. R. Farrar and M. B. Prime,“A summary review of vibration-based damage identification methods”, Shock and Vibration Digest,Vol. 30, pp. 91-105, 1998.
1
[2] P. Cawly and R. D. Adams, “The locations of defects in structures from measurements of natural frequencies”, Journal of Strain Analysis, Vol. 14, pp. 49-57, 1979.
2
[3] M. I. Friswell, J. E. T. Penny and D. A. L. Wilson,“Using vibration data and statistical measures to locate
3
damage in structures”, the International Journal of Analytical and Experimental Modal Analysis, Vol. 9, pp.239-254, 1994.
4
[4] Y. Narkis, “Identification of crack location in vibrating simply supported beams”, Journal of Sound and Vibration, Vol. 172, pp. 54 9-558, 1994.
5
[5] A. K. Pandey, M. Biswas and M. M. Samman, “Damage detection from change in curvature mode shapes”, Journal of Sound and Vibration, Vol.145, pp.321-335, 1991.
6
[6] C. P. Ratcliffe, “Damage detection using a modified Laplacian operator on mode shape data”, Journal of Sound and Vibration, Vol. 204, 505-517, 1997.
7
[7] P. F. Rizos, N.Aspragathos and A. D. Dimarogonas, “Identification of crack location and magnitude in a cantilever beam”, Journal of Sound and Vibration, Vol.138, pp. 381-388, 1990.
8
[8] A. K. Pandey and M. Biswas, “Damage detection in structures using change in flexibility”, Journal of Sound and Vibration, Vol. 169, pp. 3-17, 1994.
9
[9] S. W. Doebling, L. D. Peterson and K. F. Alvin, “Estimation of reciprocal residual flexibility from experimental modal data”, American Institute of Aeronautics and Astronautics Journal, Vol. 34, pp. 1678-1685, 1996.
10
[10] T. W. Lim, “Structural damage detection using modal test data”, American Institute of Aeronautics and Astronautics Journal, Vol. 29, pp. 2271-2274, 1991.
11
[11] O. S. Salawu, “Detection of structural damage through changes in frequencies: a review”, Engineering Structures, Vol. 19, pp. 718-723, 1997.
12
[12] Adams, R. D., Cawly, P., Pye, C. J., and Stone, B. J. “Vibration Techniques for Nondestructively Assessing the Integrity”, Journal of Mechanical Engineering Science, Vol.20 No. 2, pp. 93-100, 1978.
13
[13] W.M. Ostachowicz, M. Krawczuk, “Analysis of the Cracks on the Natural Frequencies of a cantilever Beam”, Joutnal of Sound and Vibration, Vol. 150, No.2, pp. 191-201, 1991.
14
[14] Sergio H. S. Carneiro and Daniel J. Inman, “Continuous Model for the Transverse Vibration of Cracked Timoshenko Beams”, Transactions of the ASME, Vol. 124, 310-320, 2002.
15
[15] S. P. Lele and S. K. Maiti, “Modelling of Transverse Vibration of Short Beams for Crack Detection and Measurement of Crack Extension”, Journal of Sound and Vibration, Vol. 257, No. 3, pp. 559-583, 2002.
16
[16] E. Douka, G. Bamnios, A. Trochidis, “a method for determining the location and depth of cracks in double-cracked beams”, Applied Acoustics, Vol. 65,pp. 997–1008, 2004.
17
[17] B. Binici, “Vibration of beam with multiple open cracks subjected to axial force”, J. of Sound and Vibration, Vol. 287, pp. 277–295, 2005.
18
[18] J. K. Sinha, M. I. Friswell and S. Edwards, “Simplified models for the location of cracks in beam structures using measured vibration data”, Journal of Sound and vibration, Vol. 251, No. 1, pp. 13-38, 2002.
19
[19] N. Khaji, M. Shafiei, M. Jalalpour, “Closed-form solutions for crack detection problem of Timoshenko beams with various boundary conditions”, International Journal of Mechanical Sciences, No. 51, pp. 667-681,2009.
20
[20] س. اسماعیل زاده خادم و موسی رضائی،“تعیین موقعیت و عمق ترک سرتاسری در صفحات مستطیلی با استفاده از آنالیز ارتعاشی”،، مجله بین المللی علوم مهندسی، شماره دوم، جلد نهم، زمستان 1377.29- صفحه 17
21
[21] س. اسماعیل زاده خادم، م. حاجی احمدی و موسی رضائی،“ترک یابی در لوله های ضخیم به روش آنالیز ارتعاشی”، مجله بی نالمللی علوم مهندسی، شماره ششم، جلد یازدهم، زمستان 1379 ، صفحه .165-157
22
[22] C. Mei, Y. Karpenko, S. Moody, “analytical approach to free and forced vibrations of axially loaded cracked timoshenko beams”, Journal of Sound and Vibration,Vol. 291, pp. 1041-1060, 2006.
23
[23] E. E. Gdoutos, “Fracture Mechanics”, Kluwer Academic Publishers, 2004.
24
[24] T. D. Chaudhari and S. K. Maiti, “A study of vibration of geometrically segmented beams with and without cracks”, International Journal of Solids and Structures, Vol. 37, pp. 761-779,2000.
25
[25] Young-Shin Lee, Myung-Jee Chung, “A study on crack detection using eigenfrequency test data”, Computers and Structures, No. 77, pp. 327-342, 2000.
26
ORIGINAL_ARTICLE
مطالعه تجربی- عددی خمشپذیری درکامپوزیت فلز- الیاف شیشه به منظور کاهش عیوب ناشی از فرآیند
امروزه کامپوزیتهای لایهای فلز- الیاف به دلیل دارا بودن خواص مکانیکی خوب و وزن کم بسیار مورد توجه طراحان، به ویژه صنایع هوافضا قرار گرفته اند. مواد (Fiber Metal Laminate)FML خواص بهتری نسبت به هر دو آلیاژ آلومینیوم و مواد کامپوزیتی از خود نشان میدهند. در این پژوهش، خواص خمشی این کامپوزیتها مورد بررسی عددی- تجربی قرار گرفته است. از آنجایی که این چندلایهها دارای قابلیت فرمدهی محدود میباشند و تغییرشکل الیاف الاستیک کامل است، در آنها برگشت فنری ایجاد میگردد که نوعی عیب محسوب میشود. در بخش بررسی تجربی جاری 6 مدل نمونه با زاویهی الیاف و ضخامت متفاوت از هم ساخته میشود تا مورد آزمایش خمشی قرار گیرد. به علاوه، آزمایش خمش انجام شده به روش طراحی آزمایش تاگوچی بهینه می گردد تا نتایج بدست آمده مستقل از پارامترهای قالب و پرس باشد. تأثیر پارامترهای طراحی و ساخت مانند شعاع قالب، سرعت پانچ و فشار وارد بر ورق نیز برروی برگشت فنری کامپوزیت فلزی - الیافی ساخته شده به روش لایه گذاری دستی بررسی می شود. نتایج آزمایشها نشان می دهند که اگر الیاف موازی با محور خمش باشند و ضخامت لایهی خارجی افزایش یابد کمترین شعاع خمش و زاویهی برگشتفنری ایجاد میگردد. نتایج تجربی این پژوهش با دادههای عددی بدست آمده از روش المان محدود نیز مقایسه گردیده است.
https://mej.aut.ac.ir/article_600_da4d6096ad09a2e0bd154bf9b5eaa767.pdf
2016-01-21
13
22
10.22060/mej.2016.600
کامپوزیت فلزی - الیافی
خمش
برگشتفنری
المان محدود
روش تاگوچی
سعید
امیرنژاد
saeed.amirnejad@gmail.com
1
کارشناس ارشد، مهندسی مکانیک، دانشگاه فردوسی مشهد
AUTHOR
مهران
کدخدایان
kadkhoda@um.ac.ir
2
استاد، گروه مهندسی مکانیک، دانشگاه فردوسی مشهد
LEAD_AUTHOR
[1] Borgonje, B.; Ypma, M.S.; “Long term behavior of GLARE”, Application Composite Material, vol. 10, pp.243-255, 2003.
1
[2] Burgman, Patrik. M.; “Design of experiments- The Taguchi Way”, 2nd Edition, Manufacturing Engineering, 1990.
2
[3] Carden, W.D.; Geng, L.M.; Matlock, D.K.; Wangnor,R.H.; “Measurement of spring back”, International Journal of Mechanical Sciences, vol. 44, pp. 79-101, 2002.
3
[4] Carrillo, J.G.; Cantwell, W.J.; “Scaling effects in the tensile behavior of fiber metal laminate”, International Journal of Mechanical Sciences, vol. 44, pp. 79-101, 2002.
4
[5] Chan, W.M.; Chew, H.I.; Lee, H.P.; Cheok, B.T.; “Finite element analysis of spring-back of V-bending sheet metal forming processes”, Journal of Materials Processing Technology, vol. 148, pp. 15-24, 2004.
5
[6] Huang, M.; Leu, D., “Finite-element simulation of the bending process of steel/polymer/steel laminate sheets”,Journal of Materials Processing Technology, vol. 52, pp.319-337, 1995.
6
[7] Kim, S.Y.; Choi, W.J.; Park, S.Y.; “Spring-back characteristics of fiber metal laminate (GLARE) in brake forming process”, Journal of Manufacturing Technology, vol. 32, pp. 445-451, 2007.
7
[8] Liu, Li.; Wang, Jyhwen.; “Modeling spring-back of metalpolymer- metal laminates”, Journal of manufacturing Science and Engineering, vol. 604, pp. 599-604, 2004.
8
[9] Long, A.C.; “HANDBOOK Composites forming technologies”, First Edition, Woodhead Publishing, 2007.
9
[10] Sadighi, M.; Dariushi, S.; “An experimental study on impact behavior of fiber metal laminates”, Iranian Journal of Polymer Science and Technology, vol. 21, pp. 315-327,2008.
10
[11] Sadighi, M.; Tajdari, M.; Dariushi, S.; “An investigation on tensile properties of glass fiber /aluminium laminates”,Iranian Journal of Polymer Science and Technology, vol.22, pp. 31-39, 2009.
11
[12] Sinke, J.; “Manufacturing of GLARE Parts and Structures, Applied Composite Materials”, 4th Edition,Springer, 2003.
12
[13] Standard Test Method for Tensile Properties of sheets, Annual book of ASTM Standard, D638, 2000.
13
[14] Volt, A.; Vogelesang, L.B.; De Vries, T.J.; “Towards application of fiber metal laminates in larger aircraft”,
14
Aircraft Engineering and Aerospace Technology, vol. 71,pp. 558-570, 1999.
15
[15] Wegman, R.F.; “Surface preparation techniques for adhesive bonding”, William Andrew Publishing. Noyes,1989.
16
[16] Weiss, M.; Rolfe, B.; Dingle, M.; Hodgson, P.; “The influence of interlayer thickness and properties on springback of sps- (steel/polymer/steel) laminates”, Steel Grips. Journal of Steel and Related Materials, vol. 2, pp.445-449, 2004.
17
[17] Wu, G.; Yang, J.M.; “The mechanical behavior of glare laminates for aircraft structures”, JOM. Journal in the Minerals, Metals and Materials, vol. 57, pp. 72-79, 2005.
18
ORIGINAL_ARTICLE
تحلیل اثر متغیرهای خشنکاری وایرکات بر پهنای شیار و گپ ماشینکاری مسیر مستقیم و قوس گوشه
از مهمترین مشکلات فرآیند ماشینکاری تخلیه الکتریکی سیمی (وایرکات)، دقیقنبودن هندسهی برش گوشه و قوس گوشه است. دستیابی به شکل هندسی صحیح و دقت ابعادی بالا میتواند برتری این فرآیند را استوار نماید. مطالعهی شیار برش میتواند به تحلیل و پیشبینی خطا در برش وایرکات کمک نماید. در این تحقیق، شکاف واقعی برش روی مسیر مستقیم و قوس گوشه در مرحلهی خشنکاری بررسی شده است. آزمایشها بر اساس سه متغیر فرکانس تخلیه، کشش سیم و شعاع قوس توسط روش فاکتوریل کامل طراحی شدهاند. به کمک تحلیلهای آماری اثر این متغیرها بر پهنای شیار برش روی مسیر مستقیم و قوس گوشه ارزیابی شدهاست. مقادیر تجربی گپ ماشینکاری روی مسیر مستقیم و گپ متوسط ماشینکاری روی قوس گوشه برای شرایط مختلف آزمون به دست آمدهاند. تقعر دیوارهی قوس داخلی و تحدب دیوارهی قوس بیرونی مسیر در روی قوس گوشه، در اندازهگیری پهنای شیار خطا ایجاد مینماید. در محل خروج سیم از مسیر قوس انباشتگی مواد دیده میشود. با توجه به آزمایشها و محاسبهی گپ متغیر ماشینکاری روی قوس گوشه، مقادیر تجربی انحراف سیم و خطای ماشینکاری قوس محدب گوشه محاسبه میشوند.
https://mej.aut.ac.ir/article_601_5964aa5eba45a4253f22bfa61991de09.pdf
2016-01-21
23
34
10.22060/mej.2016.601
ماشینکاری وایرکات
خطای ماشینکای
قوس گوشه
پهنای شیار
انحراف سیم
حمید
آبیار فیروزآبادی
1
کارشناس ارشد، دانشکده مهندسی مکانیک، دانشگاه یزد
AUTHOR
امیر
عبداله
amirah@aut.ac.ir
2
دانشیار، دانشکده مهندسی مکانیک، دانشگاه صنعتی امیرکبیر
AUTHOR
جمشید
پرویزیان
jparvizian@gmail.com
3
دانشیار، دانشکده مهندسی مکانیک، دانشگاه صنعتی اصفهان
LEAD_AUTHOR
[1] Obara, H., Kawai, T., Ohsumi, T., Hatano, M.,“Combined power and path control method to improve corner accuracy of rough cuts by wire EDM (1streport)”, Int J Elect Machining, Vol 8: pp.27–32, 2003.
1
[2] Obara, H., Kawai, T., Ohsumi, T., Hatano, M.,“Combined power and path control method to improve corner accuracy of rough cuts by wire EDM (2nd report)”, Int J Elect Machining, Vol 8: pp.33–8, 2003.
2
[3] Dekeyser, W. L., Snoeys, R., “Geometrical accuracy of wire-EDM”, 9th Int. Symp. on ElectroMachining (ISEM-9), pp. 226–232, Japan, 1989.
3
[4] Dodun, O., Gonçalves-Coelho, A. M., Slătineanu, L.,Nagîţ, G., “Using wire electrical discharge machining for improved corner cutting accuracy of thin parts”,Int J Adv Manuf Technol, DOI 10.1007/s00170-008-1531-4
4
[5] Hsue, W. J., Liao, Y. S., Lu, S. S., “A study of Corner Control Strategy of Wire-EDM Based on Quantitative MRR Analysis”, Int J Elect Machining, No.4, pp. 33-39, 1999.
5
[6] Sanchez, J. A., De Lacalle, L. N. L., Lamikiz, A., “A computer aided system for the optimization of the accuracy of the wire electro-discharge machining process”, Int J of Comp Integrated Manufact, Vol 17,No. 5, pp. 413–420, 2004.
6
[7] Mingqi, L., Minghui, L., Guangyao, X., “Study on the Variations of Form and Position of the Wire Electrode in WEDM-HS”, Int J Adv Manuf Technol, Vol 25: pp.929–934, 2005.
7
[8] Sanchez, J. A., Rodil, J. L., Herrero, A., De Lacalle, L. N. L., Lamikiz, A., “on the influence of cutting speed limitation on the accuracy of wire-EDM cornercutting”,J Mater Process Technol, Vol 182, No. 1–2:pp. 574–579, 2007.
8
[9] Han, F., Zhang, J., Soichiro, I., “Corner error simulation of rough cutting in wire EDM”, Precis Eng, Vol 31,No. 4: pp. 331–336, 2007.
9
[10] Han, F., Cheng, G., Feng, Z., Isago, S., “Thermomechanical analysis and optimal tension control of micro wire electrode”, Int J Mach Tools Manuf, Vol 48, pp. 922–931, 2008.
10
[11] Tosun, N., Cogun, C., Tosun, G., “A study on kerf and material removal rate in wire electrical discharge machining based on Taguchi method”, Journal of Materials Processing Technology, Vol 152, pp. 316–322, 2004.
11
[12] Yang, C. T., Song, S. L., Yan, B. H., Huang, F.Y., “Improving machining performance of wire electrochemical discharge machining by adding SiC abrasive to electrolyte”, International Journal of Machine Tools & Manufacture, Vol 46, pp. 2044–2050, 2006.
12
[13] Shichun, D., Xuyang, C., Dongbo, W., Zhenlong, W., Guanxin, C., Yuan, L., “Analysis of kerf width in micro-WEDM”, International Journal of Machine Tools & Manufacture, Vol 49, pp. 788–792, 2009.
13
[14] ASM Handbook Committee, ASM Handbook Volume 4 Heat Treating, 1991.
14
[15] User manual ROBOFIL 200, Charmilles Technologies, Switzerland, 1989.
15
[16] Montgomery, D. C., Design and analysis of experiments, Wiley, New York, 5th Ed. 2001.
16
[17] Chelladurai, H., Jain, V. K., Vyas, N. S., “Development of a cutting tool condition monitoring system for high speed turning operation by vibration and strain analysis”, Int J Adv Manuf Technol, Vol 37, pp. 471– 485, 2008.
17
[18] Pradhan, M. K., Biswas, C. K., “Neuro-fuzzy and neural network-based prediction of various responses in electrical discharge machining of AISI D2 steel”, Int J Adv Manuf Technol, Vol 50, pp. 591–610, 2010.
18
[19] Jain, V. K., Mote, R. G., “On the temperature and specific energy during electro discharge diamond grinding (EDDG)”, Int J Adv Manuf Technol, Vol 26,pp. 56–67, 2005.
19
ORIGINAL_ARTICLE
بدست آوردن روابطی برای پیش بینی مقادیر بازگشت فنری و شعاع انحنای دیواره در خمکاری U شکل ورق هایی از جنس فولاد دو فازی DP600
مهمترین محدودیت در شکل دهی مطلوب ورق های فلزی، پدیده بازیابی کشسان در طول باربرداری است که منجر به بازگشت فنری و انحنای دیواره جانبی می گردد. بنابراین پیش بینی بازگشت فنری و انحنای دیواره جانبی برای تولید محصولات دقیق ضروری است. در این تحقیق، اثر نیروی ورقگیر، ضریب اصطکاک، ضخامت ورق و استحکام تسلیم ورق بر میزان بازگشت فنری و انحنای دیواره جانبی در فرایند خمکاری U شکل ورق هایی از جنس فولاد دو فازی DP600 مورد بررسی قرار گرفته است. جهت بررسی این عوامل از نرم افزار اجزای محدود آباکوس استفاده شده و نتایج حاصل از این نرم افزار با نتایج آزمایش های عملی مورد مقایسه قرار گرفته اند. نتایج بدست آمده از آزمایش های عملی، نتایج حاصل از شبیه سازی را تصدیق می کنند. در نهایت با استفاده از نرم افزار آماری مینی تب، نتایج شبیه سازی اجزای محدود تجزیه و تحلیل شده و معادلاتی برای پیش بینی مقادیر بازگشت فنری و شعاع انحنای دیواره جانبی با استفاده از مقادیر ضریب اصطکاک، نیروی ورقگیر، ضخامت و استحکام تسلیم ورق بدست آورده شده است.
https://mej.aut.ac.ir/article_378_2c959d0f333a6b1a7e2208d9efbb467b.pdf
2016-01-21
35
44
10.22060/mej.2016.378
شکل دهی
U شکل
برگشت فنری
شعاع انحنای دیواره جانبی
فولاد دو فازی
محمد
شفیعی علویجه
mohammadshafiee2000@yahoo.com
1
دانشجوی دکتری، دانشکده مکانیک، دانشگاه بیرجند
AUTHOR
حسین
ترابیان
hssntorabian@gmail.com
2
استادیار، دانشکده مکانیک، دانشگاه آزاد اسلامی واحد تهران مرکزی
LEAD_AUTHOR
حسین
امیرآبادی
hoamirabadi@gmail.com
3
دانشیار، دانشکده مکانیک، دانشگاه بیرجند
AUTHOR
[1] Gardiner, F.J., “The springback of metals”, Trans.ASME, Vol. 79 No.1: pp. 1- 9, 1957.
1
[2] Gau, J.T. and Kinzel, G.L., “An experimental investigation of the influence of the Bauschinger effect on springback prediction”, Journal of Materials Processing Technology,Vol 108, No. 3: pp. 369- 375, 2001.
2
[3] Hama, T., Nagata, T., Teodosiu, C., Makinouchi, A. and Takuda, H., “Finite element simulation of springback
3
in sheet metal forming using local interpolation for tool surfaces”, International Journal of Mechanical Sciences, Vol 50, No.2: pp. 175- 192, 2008.
4
[4] Johnson, W. and Yu, T.X., “On springback after the pure bending of beams and plates of elastic work hardening
5
materials”, International Journal of Mechanical Sciences, Vol. 23,No.11: pp. 687- 695, 1981.
6
[5] Kim, H.S. and Koç, M., “Numerical investigations on springback characteristics of aluminum sheet metal alloys in warm forming conditions”, Journal of Materials Processing Technology, Vol 204: pp. 370-383, 2008.
7
[6] Leu, D.K., “A simplified approach for evaluating bendability and springback in plastic bending of anisotropic sheet metals”, Journal of Materials Processing Technology, Vol 66: pp. 9- 17, 1997.
8
[7] Li, G.Y., Tan, M.J. and Liew, K.M., “Springback analysis for sheet forming processes by explicit finite
9
element method in conjunction with the orthogonal regression analysis”, International Journal of Solids and Structures, Vol. 36, No.30: pp. 4653- 4668, 1999.
10
[8] Liu, G., Lin, Z., Xu, W. and Bao, Y., “Variable blankholder force in U-shaped part forming for eliminating springback error”, Journal of Materials Processing Technology, Vol. 120: pp. 259- 264, 2002.
11
[9] Liu, G., Lin, Z. and Bao, Y., “Improving dimensional accuracy of a U-shaped part through an orthogonal
12
design experiment”, Finite Elements in Analysis and Design, Vol 39, No. 2: pp. 107- 118, 2002.
13
[10] Pourboghrat, F., Karabin, M.E., Becker, R.C. and Chung, K., “A hybrid membrane/shell method for
14
calculating springback of anisotropic sheet metals undergoing axisymmetric loading”, International Journal of Plasticity, Vol 16, No. 6: pp. 677- 700, 2000.
15
[11] Pourboghrat, F. and Chu, E., “Springback in plane strain stretch/draw sheet forming”, International
16
Journal of Mechanical Sciences, Vol. 36, No. 3: pp.327- 341, 1995.
17
[12] Pourboghrat, F. and Chu, E., “Prediction of springback and side-wall curl in 2-D draw bending”, Journal
18
of Materials Processing Technology, Vol. 50: pp. 361-374, 1995.
19
[13] Ragai, I., Lazim, D. and Nemes, J.A., “Anisotropy and springback in draw-bending of stainless steel 410: experimental and numerical study”, Journal of Materials Processing Technology, Vol. 166: pp. 116- 127, 2005.
20
[14] Samuel, M., “Experimental and numerical prediction of springback and side wall curl in U-bending of
21
anisotropic sheet metals”, Journal of Materials Processing Technology, Vol. 105, No. 3: pp. 382- 393,2000.
22
[15] Siriam, S. and Wagoner, R.H., “Adding bending stiffness to 3-D membrane FEM programs”,International Journal of Mechanical Sciences, Vol 42,No. 9: pp. 1753- 1782, 2000.
23
[16] Yu, T.X. and Johnson, W., “Influence of axial force on the elastic-plastic bending and springback of a beam”,
24
Journal of Mechanical Working Technology, Vol. 6: pp.5- 21, 1982.
25
[17] Yuen, W.Y.D., “A generalised solution for the prediction of springback in laminated strip”, Journal
26
of Materials Processing Technology, Vol. 61, No. 3:pp. 254- 264, 1996.
27
[18] Zhang, Z.T. and Hu, S.J., “Stress and residual stress distributions in plane strain bending”, International
28
Journal of Mechanical Sciences, Vol. 40, No. 6: pp.533- 543, 1998.
29
[19] Zhou, D., “Bending and springback analysis using membrane elements”, Engineering Systems Design
30
and Analysis, Vol. 3: pp. 135- 142, 1996.
31
ORIGINAL_ARTICLE
بررسی رفتار الاستیک- پلاستیک مخازن کروی از جنس مواد تابعمند تحت بارگذاری فشار داخلی و اختلاف دما
با توجه به استفادهی مواد هدفمند با غیر یکنواختی های فضایی، در محیط های دمایی بالا، در کار حاضر از آن ها در مخازن کروی جدار نازک و ضخیم تحت فشار که کاربرد گسترده ای در صنعت دارند؛ استفاده شده است. براساس معادلات حاکمه، معادله دیفرانسیل تنشها در حالت پلاستیک بهدست آمده است که میتواند کاربرد گستردهای در بررسی رفتار مخازن در حالت الاستوپلاستیک داشته باشد. روی توزیع دما و روابط تنش – کرنش در این مخازن، تحت بارگذاری فشار داخلی و اختلاف دما، بحث شده است. خصوصیات این گونه مواد به صورت پارامترهایی با توابعی متغیر نسبت به شعاع در نظر گرفته شدهاند. همچنین در این کار اثر این پارامترها بر موقعیت شروع ناحیهی پلاستیک و دماهای تسلیم و روند تغییرات تنشها در طول ضخامت مخزن بررسی شده است. همچنین نشان داده شده است که با انتخاب پارامترهای مناسب میتوان ساختار مخزن را بهینه کرد.
https://mej.aut.ac.ir/article_375_23bb6b6e1cf6f263206964351abbd5cb.pdf
2016-01-21
45
52
10.22060/mej.2016.375
سختی سینماتیک خطی – مواد تابعمند – مدل پراگر – مخزن کروی– سطح تسلیم
سعید
انصاری صدرآبادی
saeid.ansari@modares.ac.ir
1
دانشجوی دکترا، دانشکده مکانیک، دانشگاه تربیت مدرس
LEAD_AUTHOR
علی
نایبی
nayebi@shirazu.ac.ir
2
دانشیار، دانشکده مکانیک، دانشگاه شیراز
AUTHOR
غلامحسین
رحیمی شعرباف
rahimi_gh@modarec.ac.ir
3
استاد،دانشکده مکانیک، دانشگاه تربیت مدرس
AUTHOR
[1] Gamer. U, “The expansion of the elastic-plastic spherical shell with nonlinear hardening”, Int. J. Mech.
1
Sci, No. 30(6), pp. 415- 26, 1988
2
[2] You. L. H , Zhang. J. J , You. X. Y, “Elastic analysis of internally pressurized thick-walled spherical pressure
3
vessels of functionally graded materials”, Int. J.pressure vessels and piping, No. 82, pp. 347- 54, 2005.
4
[3] Ahmet. N, Eraslan , Akis. T, “Plane strain analytical solutions for a functionally graded elastic-plastic
5
pressurized tube”, Int. J. pressure vessels and piping, No. 83, pp. 635- 44, 2006.
6
[4] Cheung. J. B, Chen. T. S, Thirumalai. K, “Transient thermal stresses in a sphere by local heating”, Int.
7
ASME. J. Appl. Mech, No. 41(4), pp. 930- 4, 1974.
8
[5] Takeuti. Y, Tanigawa. Y, “Transient thermal stresses of a hollow sphere due to rotating heat source”. Int. J.
9
Thermal stresses, No. 5, pp. 283- 9, 1982.
10
[6] Ootao. Y, Tanigawa. Y, “Three-dimensional transient thermal stress analysis of a nonhomogeneous hollow
11
sphere with respect to a rotating heat source”, Jpn.Soc. Mech. Eng, No. 460, pp. 2273- 9, 1994.
12
[7] Tutuncu. N, Ozturk. M, “The exact solution for stresses in functionally graded pressure vessels”, Compos. Part
13
B. Eng, No. 32(8), pp. 683- 6, 2001.
14
[8] Akis. T, “Elastoplastic analysis of functionally graded spherical pressure vessels”, Int. J. comput. mater. Sci,
15
No. 46, pp. 545- 54, 2009.
16
[9] Poultangari. R, Jabbari. M, Eslami. M. R, “Functionally graded hollow spheres under non-axisymmetric
17
thermo-mechanical loads, Int. J. pressure vessels and piping, No. 85, pp. 295- 305, 2008.
18
[10] Jabbari. M, Bahtui. A, Eslami. M. R, “Axisymmetric mechanical and thermal stresses in thick short length
19
FGM cylinders”, Int. J. pressure vessels and piping, No. 86, pp. 296- 306, 2009.
20
[11] Akhtar. S. Khan, Sujian Huang, Continuum Theory of Plasticity, John Wiely & Sons, Inc 1995.
21
[12] Lemaitre, J. L. and Chaboche, J. L., Mécanique des matériaux solides, Dunod, Paris, 1996.
22
[13] Loghman. A, Aleayoub. S.M.A, Hasani Sadi. M, “Time-dependent magnetothermoelastic creep
23
modeling of FGM spheres using method of successive elastic solution”, Applied Mathematical Modelling, No. 36, pp. 836– 845, 2012.
24
ORIGINAL_ARTICLE
بکارگیری تئوری الاستیسیته گرادیان کرنشی در بررسی اثر اندازه بر خواص الاستیک نانولوله تک جداره کربنی
در این مقاله تأثیر اثر اندازه روی خواص الاستیک نانولولههای تکجداره کربنی با استفاده از تئوری الاستیسیته گرادیان کرنشی مورد بررسی قرار گرفت. بدین منظور از مدلهای مکانیکی نظیر میله تحت کشش، نیز تیر اویلر-برنولی ومیله تحت پیچش استفاده گردید. مدل میله تحت کشش در تحقیق حاضر پایهگذاری گردید. مدل تیر اویلر-برنولی از منابع موجود استخراج و شرایط مرزی حاکم بر تیر فوق در تحقیق حاضر اصلاح گردید. ضمنا" مدل میله تحت پیچش در تحقیق حاضر پایهگذاری گردید. در تحقیق حاضر معادله ساختاری برای حالت یکبعدی کاهش یافته و استخراج گردید. معادلات حاکم و شرایط مرزی با استفاده از روش انرژی و حساب تغییرات استخراج شد. سپس از معادلات ساختاری تئوری الاستیسیته گرادیان کرنشی استفاده شد تا خواص الاستیک وابسته به اندازه، بر اساس تنش مؤثر محاسبه گردند. نتایج حکایت از آن دارد که طول نانولوله کربن روی میزان مدول یانگ در مقایسه با مدول برشی تأثیر بیشتری دارد و با کاهش طول نانولوله مدول یانگ نیز کاهش مییابد.
https://mej.aut.ac.ir/article_406_2d466ea65a5279d23dfe7ee30add40d7.pdf
2016-01-21
53
62
10.22060/mej.2016.406
تئوری الاستیسیته گرادیان کرنشی
نانولوله تکجداره کربن
اثرات اندازه
خواص الاستیک
محمود
شکریه
shokrieh@iust.ac.ir
1
استاد، دانشکده مهندسی مکانیک، دانشگاه علم و صنعت ایران
LEAD_AUTHOR
ایمان
زیبایی
iman_zibaei@mecheng.iust.ac.ir
2
کارشناس ارشد، مهندسی مکانیک، دانشگاه علم و صنعت ایران
AUTHOR
[1] Iijima S., “Helical microtubules of graphitic carbon”,Nature, Vol 354, pp. 56- 58, 1991.
1
[2] Lau K. T., “Interfacial bonding characteristics of nanotube/polymer composites”, Chem. Phys. Lett.,Vol 370, pp. 399- 405, 2003.
2
[3] Morales R. L. F., Toxvaerd, S., “Computer Simulation of a Phase Transition at Constant Temperature and
3
Pressure”, Physical Review A, Vol 34, pp. 1495- 1498,1986.
4
[4] Mindlin R. D., “Micro-structure in linear elasticity”,Archive for Rational Mechanics and Analysis, Vol 16, pp.
5
51- 78, 1964.
6
[5] Kröner E., “On the physical reality of torque stresses in continuum mechanics”, International Journal of Engineering Science, Vol 1, pp. 261- 278, 1963.
7
[6] Mindlin, R. D., Eshel, N. N., “On First Strain-Gradient theories in Linear Elasticty”, International Journal of
8
Solids and Structures, Vol 4, pp. 109- 124, 1968.
9
[7] Askes, H., Aifantis E. C., “Gradient elasticity and flexural wave dispersion in carbon nanotubes”, Physical Review B, Vol 80, pp. 195412- 195418, 2009.
10
[8] Wang L., “Wave propagation of fluid-conveying single-walled carbon nanotubes”, Computational Materials Science, Vol 49, pp. 761- 766, 2010.
11
[9] Wang B. L., Hoffman M.; Yu A. B., “Mechanics of Materials Buckling analysis of embedded nanotubes
12
using gradient continuum theory”, Mechanics of Materials, Vol 45, pp. 52- 60, 2012.
13
[10] Ansari R., Gholami R., Rouhi H., “Various gradient elasticity theories in predicting vibrational response
14
of single-walled carbon nanotubes with arbitrary boundary conditions”, Journal of Vibration and Control Vol 19, No.5, pp. 708- 719, 2012.
15
[11] Aifantis E. C., “On the role of gradients in the localization of deformation and fracture” International
16
Journal of Engineering Science, Vol 30, pp. 1279-1299, 1992.
17
[12] Muhlhaus H. B., Oka F., “Dispersion and wave propagation in discrete and continuous models for granular materials”, International Journal of Solids and Structures,Vol 33, No. 19, pp. 2841- 2858, 1996.
18
[13] Sundararaghavan V., and Waas A., “Non-local continuum modeling of carbon nanotubes: Physical
19
interpretation of non-local kernels using atomistic simulations”, Journal of the Mechanics and Physics of
20
Solids, Vol 59, No. 6, pp. 1191- 1203, 2011.
21
[14] Hu N., Fukunaga H., Lu C., Kameyama M., Yan B., and A P. R. S., “Prediction of elastic properties of carbon nanotube reinforced composites Prediction of elastic properties of carbon nanotube reinforced composites”, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, pp.1685- 1710, 2005.
22
[15] K.A. Lazopoulos, A.K. Lazopoulos, “Bending and buckling of thin strain gradient elastic beams”, European Journal of Mechanics - A/Solids Vol 29, No.5, pp. 837- 843, 2010.
23
ORIGINAL_ARTICLE
محاسبه تأثیر پارامتر جرم افزوده بر روی فرکانس سازه در سیال توسط حل عددی، تحلیلی و نتایج آزمایشگاهی
فرکانسهای طبیعی یک سازه در آب کمتر از فرکانسهای طبیعی آن در خلا می باشد و این به دلیل اثر جرم افزوده در آب می باشد[1]. در این مقاله با انجام بررسیهای تحلیلی ، ارتعاشات طبیعی ورق تقویت شده در آب بر اساس تئوری ورقهای ارتوتروپ استخراج خواهد شد و سپس یک ورق تقویت شده نمونه ساخته، تست و توسط نرم افزار ABAQUS تحلیل عددی خواهد شد. سیال مورد بررسی به صورت غیر قابل تراکم، غیر چرخشی و غیر لزج در نظر گرفته شده است.در نهایت نتایج حاصل ازحل تئوری بدست آمده ، تست و تحلیل عددی، با هم مقایسه و درصد خطا در روشهای عددی و تحلیلی بررسی می گردد و میزان اثر جرم افزوده بر روی فرکانس سازه در آب بدست می آید. و در نهایت این موضوع مشخص می گردد که فرمول تحلیلی بدست آمده با توجه به فرضیات در نظر گرفته شده برای سیال، جواب قابل قبولی می دهد.
https://mej.aut.ac.ir/article_376_71fa1da149b907c0cd76bf14e81a8b65.pdf
2016-01-21
63
72
10.22060/mej.2016.376
صفحه ارتوتروپیک
تئوری ریلی
Abaqus
جرم افزوده
فرکانس طبیعی
سید ساعد
رضوانی
saedrezvani@gmail.com
1
دانشجوی دکتری، دانشکده مهندسی دریا، دانشگاه صنعتی امیرکبیر
LEAD_AUTHOR
حمید
فاضلی
saed_troy@yahoo.com
2
استادیار، دانشکده مکانیک، دانشگاه صنعتی مالک اشتر تهران
AUTHOR
مهدی سعید
کیاست
kiasat@aut.ac.ir
3
استادیار، دانشکده مهندسی دریا، دانشگاه صنعتی امیرکبیر
AUTHOR
قاسم
حاجی هاشمی
gh.hajihashemi@gmail.com
4
کارشناسی ارشد، دانشکده مهندسی دریا، دانشگاه صنعتی مالک اشتر اصفهان
AUTHOR
[1] ا.سی.یوگورال؛ ترجمه دکتر غلامحسین رحیمی شعرباف؛ "تنش در ورقها و پوسته ها"، انتشارات دانشگاه تربیت مدرس، 1375
1
[2] Robinson N.J; palmer S.C; “A modal analysis of rectangular plate floating on an incompressible liquid”journal of sound and vibration, Vol. 142, No.3, pp-.435- 460, 1990.
2
[3] Kwak M.K; “hydro elastic vibration of rectangular plate”, Transaction of the American Society of Mechanical Engineering, Journal of Applied Mechanics, Vol. 63, No. 1,pp-.110- 115,1996.
3
[4] Haddara M.R; Cao S; “A study of the dynamic response of submerged rectangular flate plates”,Marine Structure, Vol. 9, No.10, PP-.913- 933, 1996.
4
[5] Zhou D; Cheung Y.K; “Vibration of vertical rectangular plate in contact with water on one side” Earthquake Engineering and Structural Dynamics, Vol. 29, No.5,pp-.693- 710, 2000.
5
[6] Liang C.C; Liao C.C; Tai Y.S; Lai W.H; “The free vibration analysis of submerged cantilever plates” Ocean Engineering, Vol. 28, No.9, pp-.1225- 1245,2001.
6
[7] Yadykin Y; Tenetov V; Levin D; “The added mass of a flexible plate oscillating in a fluid”, Journal of fluid and structures, vol. 17, No.1, pp-.115- 123, 2003.
7
[8] Jeong K.H; Yoo G.H; Lee S.C; “Hydroelastic vibration of two identical rectangular plates”, Journal of Sound and Vibration, vol. 272, No.3-5, pp-.539- 555, 2003.
8
[9] Ergin A; Ugurlu B; “Linear vibration analysis of cantilever plates partially submerged in fluid”, Journal of Fluid and Structures, vol. 17, No. 7, pp-. 927- 939, 2003.
9
[10] Zhou D; Liu W; “Hydroelastic vibration of flexible rectangular tanks partially with liquid”, international journal for numerical method in engineering, vol. 71,No. 2, pp-.149- 174, 2007.
10
[11] Davies H. G; “low frequency random excitation of water- loaded rectangular plates”, Journal of sound and vibration, vol. 15, pp- 107- 126, 1971.
11
[12] Y, Kerboua; “Vibration analysis of rectangular plates coupled with fluid”, Applied Mathematical Modelling,Vol, 32, pp- 2570– 2586, 2008.
12
[13] Kundu, P.K; “Fluid mechanic”, Academic Press Inc, 1990.
13
[14] Chakraverty,S; “vibration of plates”,Taylor and Francis group Boca Raton London New York, 2008.
14
ORIGINAL_ARTICLE
تحلیل عددی و تجربی ارتعاشات آزاد تیر کمانه شده
در این پژوهش ارتعاشات آزاد تیر کمانهشده به کمک روش کوادراتور دیفرانسیلی و تحلیل مودال تجربی بررسی شده است. ابتدا معادلات حاکم بر مسئله ارتعاشات تیر کمانهشده در مختصات مماسی بدست آمدهاند. این معادلات یک دستگاه معادلات دیفرانسیلی غیرخطی را تشکیل داده که پاسخ آن، مجموع پاسخهای استاتیکی و دینامیکی است. به منظور حل دستگاه معادلات دیفرانسیل غیرخطی استاتیکی ابتدا معادلات با روش کوادراتور دیفرانسیلی گسسته شده، سپس دستگاه معادلات جبری غیرخطی با استفاده از روش طول قوس حل میشوند. همچنین با توجه به کوچکتر بودن دامنه حرکت ارتعاشات آزاد تیر نسبت به دامنه حرکت استاتیکی، معادلات ارتعاشی خطی شدهاند. برای حل دستگاه معادلات دیفرانسیل ارتعاشی خطی شده، معادلات با روش کوادراتور دیفرانسیلی گسسته شده و مقادیر بدست آمده از حل معادلات استاتیکی در دستگاه معادلات گسسته شده دینامیکی جایگذاری شده است. در پایان با حل مسئله مقدار ویژه استاندارد، فرکانسهای طبیعی و شکل مودهای تیر کمانهشده بدست آمده، برای بررسی درستی روش ارائه شده، نتایج حاصل با نتایج بدست آمده از روش اجزاء محدود (به کمک نرم افزار ANSYS) و دادههای تجربی حاصل از انجام تعدادی آزمایش بر روی تیر کمانهشده ساخته شده از پی وی سی مقایسه شدند. نتایج بدست آمده نشاندهنده دقت قابل قبول و کارایی روش پیشنهادی است.
https://mej.aut.ac.ir/article_355_624ea2f7351d2a7c712a76c3a19ebf37.pdf
2016-01-21
73
84
10.22060/mej.2016.355
ارتعاشات تیر
پسکمانش
روش کوادراتور دیفرانسیلی
آنالیز مودال تجربی
پیمان
جمشیدی مقدم
p.jamshidimoghadam@gmail.com
1
کارشناس ارشد مهندسی مکانیک، شرکت آب جنوب شرق خوزستان
AUTHOR
شاپور
مرادی
moradis@scu.ac.ir
2
دانشیار، گروه مکانیک، دانشکده مهندسی، دانشگاه شهید چمران اهواز
LEAD_AUTHOR
[1] A. H. Nayfeh; W. Kreider; T.J. Anderson, “Investigation of natural frequencies and mode shapes of buckled
1
beams”, AIAA J., 33, Vol. 6, pp.1121-1126, 1995.
2
[2] B. P. Patel; M. Ganapathi; M. Touratier, “Nonlinear free flexural vibrations/post-buckling analysis of laminated
3
orthotropic beams/columns on a two parameter elastic foundation”, Composite structures, Vol 46, pp. 189-196, 1999.
4
[3] W. Lestari; S. Hanagud, “Nonlinear vibration of buckled beams: some exact solutions”, J. of solids and
5
structures, Vol 38, pp. 4741-4757, 2001.
6
[4] S. T. Santillan; L. N. Virgin; R. H. Plaut, “Post-buckling and vibration of heavy Beam on horizontal or inclined
7
rigid foundation”, J. of applied mechanics, Vol 73, pp.664-671, 2006.
8
[5] S. Neukirch; J. Frelat; A. Goriely; C. Maurini,“Vibrations of post-buckled rods: The singular inextensible limit”, J. of Sound and Vibrations,Vol 331, pp. 704-720, 2012.
9
[6] E. Reissner, “On one-dimensional finite-strain beam theory: the plane problem”, J. of Applied Mathematics
10
and Physics, Vol 23, pp. 795-804, 1972.
11
[7] Y. J. Hua; Y. Y. Zhu; C. J. Cheng, “DQEM for large deformation analysis of structures with discontinuity
12
conditions and initial displacements”, J. of Engineering Structures, Vol 30, pp. 1473-1487, 2008.
13
[8] C. Shu, Application of differential quadrature and its application in engineering, 1st edition, Verlage London, Springer, 2000.
14
[9] J. R. Quan; C. T. Chang, “New insights in solving distributed system of equations by quadraturemethod”,
15
J. of Compute Chem. Engng., Vol 13, pp.1017-1024, 1989.
16
[10] B.W.R. Forde; S.F. Stiemer, “Improved Arc Length Orthogonality Methods For Nonlinear Finite Element
17
Analysis”, J. Of Computers & Structures, Vol 27, No.5, pp. 625-630, 1987.
18
[11] S.N. Al-rasby, “Solution techniques in nonlinear structural analysis”, J. of Computers & Structures, Vol
19
40, No. 4, 985-993, 1991.
20
[12] S. Moradi; F. Taheri, “Postbuckling analysis of delaminated composite beams by differential quadrature method”, J. of Composite Structures, Vol 46, pp. 33-39, 1999.
21
ORIGINAL_ARTICLE
مقایسه روشهای شبکه عصبی مصنوعی در مدلسازی فرایند تراش کاری ماده مرکب زمینه پلیمری
در این تحقیق ماده مرکب زمینه اپوکسی پرشده با ذرات آلومینیم تهیه گردیده و با تغییر شرایط مختلف تراشکاری شامل: سرعت برش، کسر وزنی ذرات، عمق برش و نرخ پیشروی از قطعات مواد مرکب برادهبرداری صورت گرفته است. سپس زبری سطح قطعات اندازهگیری شده و برای پیشبینی اثر چهار عامل تراشکاری بر زبری سطح قطعات، با استفاده از دو نوع شبکه عصبی شامل: شبکه عصبی چند لایه پرسپترون و شبکه عصبی با تابع پایه شعاعی، مدلسازی انجام شده است. ضرایب همبستگی بین دادههای خروجی مدلها و دادههای تجربی نشان داده است که شبکه چند لایه پروسپترون نسبت به شبکه با تابع پایه شعاعی انطباق بهتری با نتایج آزمایشگاهی نشان میدهد (ضریب همبستگی 835/0 برای شبکه چند لایه پرسپترون و 524/0 برای شبکه با تابع پایه شعاعی). به علت دارا بودن ضریب همبستگی بالاتر در شبکه عصبی چند لایه پرسپترون، این شبکه برای مدلسازی تاثیر عوامل تراشکاری بر زبری سطح پیشنهاد شده است.
https://mej.aut.ac.ir/article_493_9a79fda03f9ba6e481e0bd3ffc526d9b.pdf
2016-01-21
85
100
10.22060/mej.2016.493
تراشکاری
ماده مرکب زمینه پلیمری
زبری سطح
شبکه عصبی چند لایه پرسپترون
شبکه عصبی با تابع پایه شعاعی
محمدرضا
دشت بیاض
dashtebayazi@yahoo.com
1
استادیار، گروه مهندسی مکانیک، دانشکده فنی و مهندسی، دانشگاه شهید باهنر کرمان
LEAD_AUTHOR
مهدی
قنبریان
ghanbarian_1362@yahoo.com
2
کارشناس ارشد، مهندسی مکانیک، هنرستان شهید چمران قائن
AUTHOR
[1] فضلی، محمد؛ رضاعی، سید مهدی؛ زارعی نژاد، محمد؛"بررسی،آزمایش و بهبود عملکرد عملگرمیکرونی در سنگ زنی دقیق بکمک شبکه عصبی"، نشریه علمی پژوهشی امیرکبیر 104 ، زمستان - )مهندسی مکانیک(، دوره 45 ، شماره 2، صفح 87 .1392
1
[2] قریشی، مجید؛ عصارزاده، سعید؛ "پی شبینی نرخ براده برداری و زبری سطح در فرایند ماشینکاری تخلیه الکتریکی بر اساس مدلهای شبکه عصبی"، مهندسی مکانیک مدرس، دوره 6، شماره 1، صفحه . 102-87 ، شهریور 1385
2
[3] مهدوی نژاد، رمضانعلی؛ تمیمی، کامران؛ "پیش بینی زبری سطح در ترا شکاری خشک به کمک شبک ههای فازی- عصبی - تطبیقی"، نشریه دانشکده فنی، دوره 43 ، شماره 1، صفحه 110. 103 ، بهار 1388
3
[4] Teti, R.; “Machining of Composite Materials”, CIRP Annals - Manufacturing Technology, Vol. 51: pp 611-634, 2002.
4
[5] Bishay, I.K.; Abd-El-Messieh, S.L.; Mansour, S.H.;“Electrical, mechanical and thermal properties of polyvinyl chloride composites filled with aluminum powder“, Materials and Design, Vol. 32: pp 62-68, 2011.
5
[6] Choi, S.; Kim, J.; “Thermal conductivity of epoxy composites with a binary-particle system of aluminum
6
oxide and aluminum nitride fillers”, Composites Part B: Engineering, Vol. 51: pp 140-147, 2013.
7
[7] Zhou, W.; Wang, C.; Ai, T.; Wu, K.; Zhao, F.; Gu, H.;“A novel fiber-reinforced polyethylene composite with
8
added silicon nitride particles for enhanced thermal conductivity”, Composites Part A: Applied Science and Manufacturing, Vol. 40: pp 830-836, 2009.
9
[8] Basavarajappa, S.; Ellangovan, S.; “Dry sliding wear characteristics of glass–epoxy composite filled with
10
silicon carbide and graphiteparticles”, Wear, Vol. 296:pp 491-496, 2012.
11
[9] Fu, S.Y.; Feng, X.Q.; Lauke, B.; Mai, Y.W.; “Effects of particle size, particle/matrix interface adhesion
12
and particle loading on mechanical properties of particulate–polymer composites”, Composites Part B:Engineering, Vol. 39: pp 933-961, 2008.
13
[10] Kim, H.J.; Jung, D.H.; Jung, I.H.; Cifuentes, J.I.;Rhee, K.Y.; Hui, D.; “Enhancement of Mechanical Properties of Aluminium/Epoxy Composites with Silane Functionalization of Aluminium Powder”,Composites Part B: Engineering, Vol. 43: pp. 1743-1748, 2012.
14
[11] Chung, S.; Im, Y.; Kim, H.; Park, S.; Jeong, H.;“Evaluation for Micro Scale Structures Fabricated Using Epoxy-Aluminum Particle Composite and Its Application”, Journal of Materials Processing Technology, Vol. 160: pp 168-173, 2005.
15
[12] Goyanes, S.; Rubiolo, G.; Marzocca, A.; Salgueiro, W.; Somoza, A.; Consolati, G. I.; Mondragon, G.; “Yield and internal stresses in aluminum filled epoxy resin. A compression test and positron annihilation analysis”, olymer, Vol. 44: pp 3193-3199, 2003.
16
[13] Miko, E.; Nowakowski, Ł.; “Analysis and Verification of Surface Roughness Constitution Model After Machining Process“, Procedia Engineering, Vol.39: pp 395-404, 2012.
17
[14] Benardos, P.G.; Vosniakos, G.C.; “Predicting surface roughness in machining: a review”, International Journal of Machine Tools and Manufacture, Vol. 43: pp 833-844, 2003.
18
[15] Dandekar, C.R.; Shin, Y.C.; “Modeling of machining of composite materials: A review”, International
19
Journal of Machine Tools and Manufacture, Vol. 57:pp 102-121, 2012.
20
[16] Raj, K.H.; Sharma, R.S.; Srivastava, S.; Patvardhan, C.; “Modeling of manufacturing processes with ANNs
21
for intelligent manufacturing”, International Journal of Machine Tools and Manufacture, Vol. 40: pp 851-868,
22
[17] Gururaja, S.; Ramulu, M.; Pedersen, W.; “Machining of MMCs a Review”, Machining Science and
23
Technology, Vol. 17: pp 41–73, 2013.
24
[18] Zhang, Z.; Friedrich, K.; “Artificial neural networks applied to polymer composites: a review”, Composites
25
Science and Technology, Vol. 63: pp 2029-2044, 2003.
26
[19] http://www.pmpcompany.ir.
27
[20] DIN EN ISO 4287:2010-07, Geometrical Product Specifications (GPS) - Surface texture: Profile method
28
- Terms, definitions and surface texture parameters (ISO 4287:1997).
29
[21] Sheikh-Ahmad, G.Y.; “Machining of Polymer Composites”, Springer Science, New York, USA,2009.
30
[22] Xiao, K.Q.; Zhang, L.C.; “The Role of Viscous Deformation in the Machining of Polymers”.International Journal of Mechancial Sciences, Vol. 44:pp 2317–2336, 2002.
31
[23] El-Sonbaty, I.; Khashaba, U.A.; Machaly, T.;“Factors Affecting the Machinability of GFR/Epoxy Composites”, Composite Structures, Vol. 63: pp 329-338, 2004.
32
[24] Zunjarrao, S.C.; Singh, R.P.; “Characterization of the Fracture Behavior of Epoxy Reinforced with Nanometer and Micrometer Sized Aluminum Particles”, Composites Science and Technology, Vol.66: pp 2296-2305, 2006.
33
[25] Pendse, D.M.; Joshi, S.S.; “Modeling and Optimization of Machining Process in Discontinuously Reinforced
34
Aluminum Matrix Composites”, Machining Science and Technology: An International Journal, Vol. 8: pp 85–102, 2004.
35
[26] Basheer, A.C.; Dabade, U.A.; Joshi, S.S.;Bhanuprasad, V.V.; Gadre, V.M.; “Modeling of Surface Roughness in Precision Machining of Metal Matrix Composites Using ANN”, Journal of Materials Processing Technology, Vol. 197: pp 439-444, 2008.
36
[27] An, S.-O.; Lee, E.-S.; Noh, S.-L.; “A Study on the Cutting Characteristics of Glass Fiber Reinforced Plastics with Respect to Tool Materials and Geometries”, Vol. 68: pp 60-67, 1997.
37
[28] Carr. J.W.; Feger, C.; “Ultraprecision Machining of Polymers”, Precision Engineering. Vol. 15: pp 221–237, 1993.
38
[29] Hagan, M.T.; Demuth, H.B.; Beale, M.H.; “Neural Network Design”, PWS Publishing, Boston, 1996.
39
[30] The Math Works Inc., Product, Neural Network Toolbox Version 7.6 MATLAB® 7.6 Release 14 Service Pack 3, 2008.
40