Ababaf Behbahani, Mohammad Hosein Effects of air injection at rotor blade row tip region of an axial compressor on its performance under inlet distortion conditions [Volume 53, Issue 3 (Special Issue), 2021, Pages 1729-1744]
Abbasalizadeh, Majid Experimental Investigation of Thermal Performance of Pulsating Heat Pipe at Angles Close To the Horizon [Volume 53, Issue 11, 2022, Pages 5445-5460]
Abbasi, Omid Reza Numerical study of the effect of left coronary artery stenosis on vascular tissue oxygenation [Volume 53, Issue 3 (Special Issue), 2021, Pages 1767-1782]
Abbasi, sarallah Effect of blowing on flow-induced noise reduction in a rod-airfoil [Volume 53, Issue 3 (Special Issue), 2021, Pages 1783-1798]
Abbasian, Saman Reconstruction of Electrical Tomography Images based on Parameter Estimation Method in Inverse Heat Transfer [Volume 53, Issue 1 (Special Issue), 2021, Pages 483-498]
Abbasian Arani, Ali Akbar Hydrothermal performance of trapezoidal fin equipped with vortex generator and hole: Investigation of the effect of vortex generator and hole position [Volume 53, Issue 3 (Special Issue), 2021, Pages 1963-1980]
Abbasian Arani, Ali Akbar Numerical simulation of salt gradient solar pond by employing the solar radiation estimating function considering wall-shading effects [Volume 53, Issue 5 (Special Issue), 2021, Pages 3385-3400]
Abdi Aghdam, Ebrahim Investigation of the response of a multi-zone simulation code equipped with blow-by sub-model in a dual fuel spark-ignition engine [Volume 53, Issue 5, 2021, Pages 3035-3056]
Abdizadeh, Gholamreza Numerical Investigation of Hybrid Wick Structure Effect on Thermal Performance of a Thin Flat Heat Pipe [Volume 53, Issue 11, 2022, Pages 5485-5504]
Abdollahi, Hassan Increasing the Sensitivity of SiO2/Al Micro Cantilever Infrared Detector Based on Micro Electromechanical Systems Technology by Optimizing of Dimensions [Volume 53, Issue 8, 2021, Pages 4717-4728]
Abdollahi, Mohammad Experimental verification of indirect bridge mode shape identification using transmissibility of a passing vehicle [Volume 53, Issue 6, 2021, Pages 3529-2548]
Abdollah Nezhad, Qasem Thermo-Economic Evaluation of a Power and Freshwater Production System Including a Liquid Metal Magnetohydrodynamic Unit Driven By a Concentrated Solar Tower and Biogas [Volume 53, Issue 11, 2022, Pages 5551-5572]
Abdullah, Amir Experimental Study of the Effect of Initial Surface Roughness on Ball Burnishing Forces and Endurance Limit of AISI 4130 Hardened Steel [Volume 53, Issue 12, 2022, Pages 5627-5644]
Abedi Ravan, Bahram Feasibility study of single point incremental forming of aircraft canopy for polycarbonate sheet [Volume 53, Issue 4 (Special Issue), 2021, Pages 2751-2768]
Abolghasemi, Abolghasem Simulation of Effective Parameters on Desalination Water Using Capacitive Deionization Method [Volume 53, Issue 11, 2022, Pages 5595-5612]
AbouAli, Omid Numerical study of the effect of left coronary artery stenosis on vascular tissue oxygenation [Volume 53, Issue 3 (Special Issue), 2021, Pages 1767-1782]
Aboufazeli, Nima Experimental study on effective parameters on vertical axis wind turbine performance [Volume 53, Issue 5, 2021, Pages 2771-2790]
Abtahi, Mahdi Numerical analysis of chaotic dynamics in vehicle along with design of chaos controller using fuzzy fast terminal sliding mode control [Volume 53, Issue 4 (Special Issue), 2021, Pages 2539-2556]
Adibi, Hamed Experimental and Numerical Investigation of Fatigue Behavior of Polylactic acid Components Made by Additive Manufacturing Method [Volume 53, Issue 6, 2021, Pages 3703-3716]
Afkhami, Sina Numerical Analysis of Cross Section Time Variation Effects of the Supersonic Exhaust Diffuser [Volume 53, Issue 3, 2021, Pages 1469-1486]
Afrand, Masoud Numerical/Experimental Investigation of the Presence of a Protuberance in a Convergent – Divergent Nozzle in Supersonic Regime to Control the Thrust Vector [Volume 53, Issue 9, 2021, Pages 4887-4904]
Afshari, Ebrahim Investigation of the Humidifier Performance of Adding Gas Diffusion Layers Around Membrane for Fuel Cell Application [Volume 53, Issue 3, 2021, Pages 1653-1666]
Afshari, Ebrahim Numerical Simulation of Variable Conductance Heat Pipe with Cold Reservoir by Single Phase Flow Approach [Volume 53, Issue 9, 2021, Pages 4905-4924]
Afzalian, Mahdi Experimental evaluation of the effect of supply air direction on air current and temperature in a room with underfloor air distribution system [Volume 53, Issue 5, 2021, Pages 3057-3076]
Aghaei, Mohammad Numerical simulation of water hammer in various fluids due to a fast valve closure [Volume 53, Issue 7, 2021, Pages 4171-4188]
Agheli Hajiabadi, Mohammad Mahdi Study of the Motion Behavior of Soft Fiber Reinforced Actuators Based on Fiber Angle [Volume 53, Issue 8, 2021, Pages 4565-4580]
Ahanian, Ali Free vibration and flexural-torsional stability analyses of axially functionally graded tapered thin-walled beam resting on elastic foundation [Volume 53, Issue 6, 2021, Pages 3587-3614]
Ahmadi, Bahman Denoising vibration signals of rotating machines using probability density function, similarity measure and improved thresholding function [Volume 53, Issue 4 (Special Issue), 2021, Pages 2493-2512]
Ahmadi, Goodarz Investigation of the Effect of Ventilation System Inlet Location on Particle Motion in a Room Using Multi Relaxation Time-Lattice Boltzmann Method [Volume 53, Issue 3, 2021, Pages 1457-1468]
Ahmadi, Habib Kinematic Optimization of the Stirling engine for Maximum Output Work and Constraint of Occupied Space [Volume 53, Issue 7, 2021, Pages 4455-4480]
Ahmadi, Habib Superharmonic and Subharmonic Resonance Analysis of A Rectangular Hyperelastic Membrane Resting on Nonlinear Elastic Foundation Using The Method of Multiple Scales [Volume 53, Issue 8, 2021, Pages 4535-4564]
Ahmadi, Hamed Comparison of penetration process of 2-layer elastomeric composite with thermoset composite using energy absorption equations [Volume 53, Issue 6, 2021, Pages 3657-3672]
Ahmadi, Javad Actuators redundancy resolution scheme with computational time reduction purpose for parallel cable robots with considering the rupture limits of the cables [Volume 53, Issue 6, 2021, Pages 3479-3496]
Ahmadi, Mohmmad Hossein Kinematic Optimization of the Stirling engine for Maximum Output Work and Constraint of Occupied Space [Volume 53, Issue 7, 2021, Pages 4455-4480]
Ahmadi, Morteza Micro-Mechanical Damage Analysis of Al-TiC Particulate Reinforced Composites by Peridynamic Theory [Volume 53, Issue 8, 2021, Pages 4701-4716]
Ahmadi, Salman Planar Object Manipulation with Multi Fingers Robot Located on a Moving Hand Under Rolling Grasp Constrains [Volume 53, Issue 2, 2021, Pages 943-958]
Ahmadian, Bahram Response analysis of primary cilia of the cell to the oscillatory fluid flow by using fluid-structure interaction method [Volume 53, Issue 5 (Special Issue), 2021, Pages 3293-3306]
Ahmadian, Hamid Sensitivity Analysis of Rotor Dynamic Behavior to Manufacturing Tolerances Based on Global Sensitivity Analysis and Statistical Methods [Volume 53, Issue 8, 2021, Pages 4501-4516]
Ahmadi Nadooshan, Afshin Effects of Magnetic Field on Natural Convection of Non-Newtonian Fluid in a Square Enclosure with a Central Heat Source [Volume 53, Issue 1, 2021, Pages 259-278]
Ahmadi Nodoushan, Afshin Numerical simulation of mixed convection of Bingham fluid between two coaxial cylinders [Volume 53, Issue 5 (Special Issue), 2021, Pages 3417-3428]
Ahmadpour, Ali Numerical Simulation of Non-Newtonian Blood Flow in A Three-Dimensional Non-Planar Bifurcation with Stenosis [Volume 53, Issue 9, 2021, Pages 4865-4886]
Ahmadvand, Reza Modified Variable Structure Estimation and Control for Constrained Landing on Mars [Volume 53, Issue 10, 2022, Pages 5055-5068]
Ajabshirchi, Yahya Energy, Exergy and Economic Analysis of a Semi-solar Greenhouse with Experimental Validation [Volume 53, Issue 3, 2021, Pages 1677-1694]
Ajam, Hossein Evaluation of Combustion Models in a Porous Medium with Different Excess Air Ratios [Volume 53, Issue 1, 2021, Pages 65-80]
Ajori, Shahram Analyzing the effect of adsorption of Flavin Mononucleotide biomolecule on the natural frequency of biocompatible boron-nitride nanotubes [Volume 53, Issue 4 (Special Issue), 2021, Pages 2577-2588]
Akbari, Davood Non-destructive evaluation of internal cracks in glass fiber-reinforced polymers using digital shearing interferometry [Volume 53, Issue 6 (Special Issue), 2021, Pages 4063-4078]
Akbari, Sepideh Kinematic Modeling of a Spatial Soft Robot by an Improved Analytical Method Based on Serial Robots [Volume 53, Issue 2 (Special Issue), 2021, Pages 1065-1080]
Akbari kangarluei, Rostam Experimental Investigation of Thermal Performance of Pulsating Heat Pipe at Angles Close To the Horizon [Volume 53, Issue 11, 2022, Pages 5445-5460]
Akbarzadeh, Ali Experimental and Numerical Investigation of Film Cooling Effectiveness on Squealer Tip of a Turbine Blade [Volume 53, Issue 3, 2021, Pages 1521-1536]
Akbarzadeh, Saleh Transient numerical modeling and experimental investigation of the effect of surface texture on elastohydrodynamic lubrication [Volume 53, Issue 5 (Special Issue), 2021, Pages 3201-3212]
Alaeipour, Maryam Sadat Techno-Economic Feasibility of Energy Supply Systems from Renewable Sources of Solar and Biomass in Rural Areas Located In Cold and Dry Climate [Volume 53, Issue 1, 2021, Pages 81-100]
Alavi, Fatemeh Sadat Prediction of femoral fracture pattern using finite element analysis of dual-energy X-ray absorptiometry -based model [Volume 53, Issue 2 (Special Issue), 2021, Pages 1223-1236]
Alavi, Fatemeh Sadat The Prediction of Femoral Fracture Location Using Extended Finite Element Method [Volume 53, Issue 8, 2021, Pages 4595-4608]
Alavi, Seyed Mahmood Abulhasan Numerical simulation of nanofluid flow in an annulus with porous baffles based on combination of Darcy-Brinkman-Forchheimer model and two-phase mixture model [Volume 53, Issue 3 (Special Issue), 2021, Pages 1897-1914]
Alimehr, Ashkan Experimental Investigation of a High Aspect Ratio Rectangular Liquid Jet in Parallel Airflow [Volume 53, Issue 11, 2022, Pages 5429-5444]
Alinia, Yadollah Thermal stress analysis for an aluminum die cast die [Volume 53, Issue 4 (Special Issue), 2021, Pages 2687-2702]
Alipoor, Alireza Numerical Simulation of Liner Vibrations in a Laboratory Combustion Chamber [Volume 53, Issue 2, 2021, Pages 881-896]
Alipour, Alireza One-dimensional Combustion Simulation for Different Hydrogen-enriched Natural Gas Blends [Volume 53, Issue 1, 2021, Pages 53-64]
AliSadeghi, Hamed Development of Blade Element Momentum Theory for Unsteady Flow with Regard to the Dynamic Stall Phenomenon [Volume 53, Issue 3, 2021, Pages 1439-1456]
Alizadeh, Elham Mechanical Properties and Structural Behavior of Bone at Nano Scale with Cohesive Element [Volume 53, Issue 2, 2021, Pages 745-776]
Alizadeh Jajarm, Alireza Experimental investigation on MWCNTs-COOH nano fluid on 3D oscillating heat pipe [Volume 53, Issue 5 (Special Issue), 2021, Pages 3401-3416]
Allahdadi, Nazila Numerical Investigation of the Performance of Hydrogen Production Process by Production Gas Recirculation [Volume 53, Issue 1 (Special Issue), 2021, Pages 623-638]
Ameri, Mehran Thermodynamic and Thermo-Economic Analysis of the Absorption Heat Transformer, Organic Rankine Cycle, and Reverse Osmosis Desalination Combined System [Volume 53, Issue 1 (Special Issue), 2021, Pages 639-654]
Ameri, Mehran Investigation of using hybrid nanofluid-phase change material spectral splitter in photovoltaic/thermal system [Volume 53, Issue 7, 2021, Pages 4429-4454]
Ameri, Mehran Performance investigation of freezing desalination coupled with carbon dioxide refrigeration system [Volume 53, Issue 5 (Special Issue), 2021, Pages 3351-3366]
Ameri, Mehran Energy and Exergy Analysis of Organic Rankine Cycle Fed by Electric Arc Furnace Waste Heat [Volume 53, Issue 9, 2021, Pages 4999-5016]
Amini, Hassan Investigation of Crack Growth in Deposited and Perfect Titanium/Titanium Nitride Structure by Molecular Dynamic Simulation [Volume 53, Issue 2, 2021, Pages 833-850]
Amini Froshani, Javad Numerical simulation of salt gradient solar pond by employing the solar radiation estimating function considering wall-shading effects [Volume 53, Issue 5 (Special Issue), 2021, Pages 3385-3400]
Aminivida, Hamed Thermal Stress Analysis of the Carbon Nanotube Reinforced Composite Cylindrical Shells [Volume 53, Issue 10, 2022, Pages 5269-5292]
Amiri Delouei, Amin Analytical Solution of Heat Transfer in a Cone Made of Functionally Graded Material [Volume 53, Issue 1 (Special Issue), 2021, Pages 539-552]
Amiri Delouei, Amin Investigation of the Effect of Ventilation System Inlet Location on Particle Motion in a Room Using Multi Relaxation Time-Lattice Boltzmann Method [Volume 53, Issue 3, 2021, Pages 1457-1468]
Amirii, Yasaman Fluid-Structure Interactions Analysis of Tension in An Axon Using Finite Elements Modeling to Investigate Strain Related Neurological Damages [Volume 53, Issue 8, 2021, Pages 4609-4632]
Amjadigolpayegani, Ashkan Analysis of Density Wave Oscillations in a Boiling Channel by a New Analytical Model [Volume 53, Issue 3, 2021, Pages 1505-1520]
Amjadi Golpayegani, ashkan Modeling and parametric analysis of two-phase fluid stability in boiling process in a thermal channel [Volume 53, Issue 3 (Special Issue), 2021, Pages 1861-1882]
Amjadi Manesh, Hossian Numerical study of the effect of left coronary artery stenosis on vascular tissue oxygenation [Volume 53, Issue 3 (Special Issue), 2021, Pages 1767-1782]
Anani, Yavar Comparison of penetration process of 2-layer elastomeric composite with thermoset composite using energy absorption equations [Volume 53, Issue 6, 2021, Pages 3657-3672]
Anani, Yavar Nonlinear analysis of hyperelastic plates using first-order shear deformation plate theory and a meshless method [Volume 53, Issue 4, 2021, Pages 2331-2346]
Ansari, Mahdi Numerical Simulation of Elastoplastic Behavior and Damage Evolution at Various Stress Triaxiality [Volume 53, Issue 12, 2022, Pages 5703-5724]
Ansari, Mohammad Experimental investigation of heat transfer and pressure drop in perforated ribs in the solar air heater channel [Volume 53, Issue 3 (Special Issue), 2021, Pages 1981-2000]
Arab, Reza Free and Forced Vibration Analysis of Stiffened Cylindrical Shells under Moving Internal Pressure [Volume 53, Issue 12, 2022, Pages 5867-5886]
Arab Maleki, vahid Piezoelectric Energy Harvesting Using a Porous Beam Under Fluid-Induced Vibrations [Volume 53, Issue 8, 2021, Pages 4633-4648]
Araghchi, Masoud Effect of Graphene Sheets Aggregation on The Dislocation-Blocking Mechanism of Nanolaminated Aluminum/Graphene Composite: Molecular Dynamics Simulation Study [Volume 53, Issue 8, 2021, Pages 4649-4664]
Aramesh, Arash Thermodynamic and Thermo-Economic Analysis of the Absorption Heat Transformer, Organic Rankine Cycle, and Reverse Osmosis Desalination Combined System [Volume 53, Issue 1 (Special Issue), 2021, Pages 639-654]
Ardakani, Mohammad Ali Experimental Investigation on Flow Downstream of a Triangular Bluff Body at Different Angles [Volume 53, Issue 1 (Special Issue), 2021, Pages 427-436]
Ardekani, Ehsan Experimental Investigation on Flow Downstream of a Triangular Bluff Body at Different Angles [Volume 53, Issue 1 (Special Issue), 2021, Pages 427-436]
Arghand, Hesam Addin Prognostics of rolling element bearings using shock pulse method and vibration method records and employing feedforward neural-network [Volume 53, Issue 4 (Special Issue), 2021, Pages 2557-2576]
Arsalani, Moosa Experimental Study of the Effect of Initial Surface Roughness on Ball Burnishing Forces and Endurance Limit of AISI 4130 Hardened Steel [Volume 53, Issue 12, 2022, Pages 5627-5644]
Asadi, Abbas Variable distance interdigitated electrodes design to improve the performance of cantilever piezoelectric thin films nanogenerators [Volume 53, Issue 4, 2021, Pages 2347-2366]
Asadi, Ali Experimental Study of the Effect of Fluid Jet Swirl on Circular Hydraulic Jump [Volume 53, Issue 7, 2021, Pages 4153-4170]
Asadigorgi, Hasan Using nonlinear energy sink to improve the dynamic behavior of rectangular plate under supersonic aerodynamic flow at different angles [Volume 53, Issue 6, 2021, Pages 3511-3528]
Asefi, Amin Numerical Investigation of the Influence of Burner’s Bluff Body on Air-Fuel Mixing and Reaction [Volume 53, Issue 9, 2021, Pages 4981-4998]
Asemani, Seyedeh Samaneh Comparison of penetration process of 2-layer elastomeric composite with thermoset composite using energy absorption equations [Volume 53, Issue 6, 2021, Pages 3657-3672]
Asgari, Masood A new method for estimating the compressive strain of cellular structures using microstructure of foams based on Laguerre tessellations [Volume 53, Issue 6, 2021, Pages 3629-3644]
Asgary, Masoud Effect of Graphene Sheets Aggregation on The Dislocation-Blocking Mechanism of Nanolaminated Aluminum/Graphene Composite: Molecular Dynamics Simulation Study [Volume 53, Issue 8, 2021, Pages 4649-4664]
Asgharzadeh, Alireza Measurement of subcooled flow boiling heat transfer coefficient in vertical annulus tube [Volume 53, Issue 7, 2021, Pages 4345-4360]
Ashrafi Khorasani, Nariman Stability analysis of shear-thinning flow in narrow gap Taylor–Couette axial flow [Volume 53, Issue 3 (Special Issue), 2021, Pages 1745-1766]
Askari, Amir Reza Investigating the Influence of Higher-Order Boundary Conditions on Free Vibrations of Bi-Directional Functionally Graded Thick Conical Micro-Shells [Volume 53, Issue 10, 2022, Pages 5085-5104]
Askarifard Jahromi, Hamid Raza Numerical simulation of mixed convection of Bingham fluid between two coaxial cylinders [Volume 53, Issue 5 (Special Issue), 2021, Pages 3417-3428]
A.S. Mirzabozorg, Mohsen Investigation of Geometric Characteristics on the Non-Reaction Supersonic Flow inside the Channel with the Presence of Cavities [Volume 53, Issue 11, 2022, Pages 5409-5428]
Ayat, Amir Analyzing driving behavior based on vehicle information logging using MPU6050 [Volume 53, Issue 6 (Special Issue), 2021, Pages 3855-3874]
Ayatollahi, Majid Reza Experimental and Theoretical Assessment of Mode II Fracture Toughness for Cracked Ductile Specimens with High Strain-Hardening [Volume 53, Issue 10, 2022, Pages 5141-5158]
Ayoobi, Ahmadreza Experimental Investigation of the Performance of Trailing Edge Noise-Reducing Finlets [Volume 53, Issue 9, 2021, Pages 4827-4846]
Azadi, Mohammad Sensitivity analysis of fracture behavior in carbon-epoxy composite at different displacement rates under mode I tensile loading by regression analysis [Volume 53, Issue 4 (Special Issue), 2021, Pages 2671-2686]
Azadi, Mohammad Comparison of Support Vector Machine and K-Means Algorithms Performance in Extracting the Real Driving Cycle of Combined Tehran-Amol [Volume 53, Issue 9, 2021, Pages 5017-5036]
Azadi, Shahram Combination of active braking and semi-active suspension systems to improve the roll and yaw vehicle stability [Volume 53, Issue 6, 2021, Pages 3549-3570]
Azadi Talab, Vahid Modeling of turbulent atmospheric boundary layer and dispersion of solid pollutant particles in an urban area using large eddy simulation [Volume 53, Issue 5, 2021, Pages 2839-2856]
Azami, Behnam Transient numerical modeling and experimental investigation of the effect of surface texture on elastohydrodynamic lubrication [Volume 53, Issue 5 (Special Issue), 2021, Pages 3201-3212]
Azamirad, Ghasem Study and Optimization of Effective Parameters in The Occurrence of Blush Defect in The Plastic Injection Molding Process by Analysis of Variance [Volume 53, Issue 10, 2022, Pages 5293-5308]
Azarafza, Reza Dynamic analysis of cylindrical sandwich shell with orthogonal stiffeners using high-order theory [Volume 53, Issue 4 (Special Issue), 2021, Pages 2473-2492]
Azarkish, Hassan Design and Multi-Objective Optimization of A Magnetohydrodynamic Drug Delivery Infusion Micropump [Volume 53, Issue 10, 2022, Pages 5221-5238]
Azhdary Moghaddam, Mahdi Investigation on flow air concentration effect on distance of the chute spillway aerators [Volume 53, Issue 5 (Special Issue), 2021, Pages 3135-3150]
Azizi, Saeed Effect of Air Curtain on Occupants Thermal Comfort and Indoor Air Quality in an Athletic Swimming Pool with Spectators’ Stand [Volume 53, Issue 1, 2021, Pages 191-208]
B
Bab, Saeed Out-of-Plane Vibration Mitigation of Wind Turbine Blade Using Highly Efficient Nonlinear Energy Sink [Volume 53, Issue 12, 2022, Pages 5851-5866]
Babaei, Hashem Plastic Deformation of Reinforced Aluminum Plates with Polyurea Coating under Impulsive Loading [Volume 53, Issue 2 (Special Issue), 2021, Pages 1251-1268]
Babaei, Hashem Effect of intense impulsive loading on performance of multi-layered plates [Volume 53, Issue 4 (Special Issue), 2021, Pages 2639-2670]
Babaei, Hashem Investigation of penetration behavior of monolithic and multi-layered metallic targets subjected to a projectile impact [Volume 53, Issue 4, 2021, Pages 2309-2330]
Babaei, Hashem Experimental investigation and mathematical modeling of the response of circular metallic plates under successive intense dynamic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 4023-4050]
Badri Ghavifekr, Habib Design and simulation of a biosensor based on a microelectromechanical resonator array [Volume 53, Issue 6 (Special Issue), 2021, Pages 3841-3854]
Bafekr, Sajed Hadi The Effect of Non-Newtonian Behavior on the Transport of Low Density Lipoprotein Particles in the Vortex Region in the Human Carotid Artery [Volume 53, Issue 9, 2021, Pages 4789-4806]
Baghani, Mostafa Finite Element Modeling of a Novel Magnetic Shape Memory Alloy Based Energy Harvester Using a Corrugated Beam and Investigating the Effective Parameters [Volume 53, Issue 2, 2021, Pages 799-814]
Baghani, Mostafa Finite element modeling of shape memory alloy stent insertion in the vessel with consideration of vessel damage [Volume 53, Issue 2 (Special Issue), 2021, Pages 1211-1222]
Bagheri, Ahmad Denoising vibration signals of rotating machines using probability density function, similarity measure and improved thresholding function [Volume 53, Issue 4 (Special Issue), 2021, Pages 2493-2512]
Bagheri-Esfeh, Hamed Comparison of natural and synthetic carotid arteries in the normal and occluded cases considering the effect of blood on elastic wall of artery [Volume 53, Issue 5, 2021, Pages 2821-2838]
Baheri Islami, Sima Energy, Exergy and Economic Analysis of a Semi-solar Greenhouse with Experimental Validation [Volume 53, Issue 3, 2021, Pages 1677-1694]
Baheri Islami, Sima Experimental study on the enhancement of the thermal efficiency of a household gas water heater [Volume 53, Issue 3 (Special Issue), 2021, Pages 2013-2030]
Bahmani, Ehsan One-dimensional Combustion Simulation for Different Hydrogen-enriched Natural Gas Blends [Volume 53, Issue 1, 2021, Pages 53-64]
Bahoosh Kazerooni, Reza Investigation of Heat Transfer of Non-Newtonian Pseudo-Plastic Fluids in Porous Heat Exchangers [Volume 53, Issue 1, 2021, Pages 241-258]
Bahrami, Mohammad Amin A study on the synergistic influence of reduced graphene oxide and MWCNTs on the mechanical properties of epoxy nanocomposite [Volume 53, Issue 6 (Special Issue), 2021, Pages 3971-3986]
Bahrami Joo, Behzad Designing Optimum Multi-Domain System by Integrating Bond Graph and Genetic Programming [Volume 53, Issue 2, 2021, Pages 1015-1038]
Bajalan, Sima Simulation of Two-Phase Flow and Heat Transfer in a Channel and around a Tube by Lattice-Boltzmann Method [Volume 53, Issue 1 (Special Issue), 2021, Pages 499-516]
Bakhsheshy, Ali The effect of accuracy of the length scale parameter on natural frequencies of porous rectangular microplate [Volume 53, Issue 2 (Special Issue), 2021, Pages 1179-1196]
Baniasad Askari, Ighball Thermodynamic and Thermo-Economic Analysis of the Absorption Heat Transformer, Organic Rankine Cycle, and Reverse Osmosis Desalination Combined System [Volume 53, Issue 1 (Special Issue), 2021, Pages 639-654]
Barati, Amir Hossein Fault detection and isolation based on robust Kalman filter for discrete-time systems with stochastic and norm-bounded uncertainties [Volume 53, Issue 6 (Special Issue), 2021, Pages 3825-3840]
Barati, Ebrahim Numerical simulation simultaneous use of longitudinal ventilation and smoke extraction from the ceiling in fires inside tunnels [Volume 53, Issue 7, 2021, Pages 4411-4428]
Barimani Varandi, Abozar Feasibility study of single point incremental forming of aircraft canopy for polycarbonate sheet [Volume 53, Issue 4 (Special Issue), 2021, Pages 2751-2768]
Barzegari, Mohammad Mahdi Numerical and Experimental Modal Analysis of a 400 W Polymer Electrolyte Membrane Fuel Cell [Volume 53, Issue 1, 2021, Pages 101-116]
Barzegari, Mohammad Mahdi Experimental and numerical investigation of the plastic deformation of metallic bipolar plates with serpentine flow filed [Volume 53, Issue 6, 2021, Pages 3717-3732]
Bashirnezhad, kazem Experimental investigation on MWCNTs-COOH nano fluid on 3D oscillating heat pipe [Volume 53, Issue 5 (Special Issue), 2021, Pages 3401-3416]
Basti, Ali Analysis of Forming Limit of Sheet Metals Considering Vertex Localized Necking and Ductile Damage Criterion [Volume 53, Issue 2 (Special Issue), 2021, Pages 1307-1320]
Bavarsad, Anna Nonlinear optimal control of an active transfemoral prosthesis using state dependent Riccati equation approach [Volume 53, Issue 4, 2021, Pages 2117-2136]
Bazargan, Majid Experimental investigation of heat transfer and pressure drop in perforated ribs in the solar air heater channel [Volume 53, Issue 3 (Special Issue), 2021, Pages 1981-2000]
Bazargan lari, Yousef Control of the Amount of Oncolytic Virus Injection by Considering Time Delay [Volume 53, Issue 2 (Special Issue), 2021, Pages 1125-1136]
Bedram, Ahmad Analytical-Numerical Investigation of Unequal Sized Droplets of Dilatants' Fluid in T-Junction with Unequal Length Branches [Volume 53, Issue 3, 2021, Pages 1417-1438]
Behmounesi, Seyed Amir Theoretical comparison of thermal and electrical performance of different models of sheet and tube type solar photovoltaic - thermal water collector [Volume 53, Issue 5, 2021, Pages 2903-2920]
Behzad, Mehdi Prognostics of rolling element bearings using shock pulse method and vibration method records and employing feedforward neural-network [Volume 53, Issue 4 (Special Issue), 2021, Pages 2557-2576]
Beigpour, Reza Thermal Stress Analysis of the Carbon Nanotube Reinforced Composite Cylindrical Shells [Volume 53, Issue 10, 2022, Pages 5269-5292]
Bidabadi, Mahdi Analytical model for the non-premixed combustion of the titanium dust cloud in counter-flow geometry [Volume 53, Issue 5 (Special Issue), 2021, Pages 3307-3316]
Biglari, FaridReza Micromechanical Damage Model for Plasticity of Metals to Predict Failure under Shear Loads [Volume 53, Issue 12, 2022, Pages 5679-5702]
Biglari, Hamed Employing of shunt damping method to reduce edgewise vibration of small size wind turbine blade with considering the effect of vibration coupling [Volume 53, Issue 4, 2021, Pages 2073-2088]
Bostani, Hadis An Experimental Investigation on the Convective Heat Transfer Coefficient and Nusselt Number in Water/Carbon Nanofluid [Volume 53, Issue 1, 2021, Pages 209-220]
Bozorgmehrian, Maryam An Experimental Investigation on the Convective Heat Transfer Coefficient and Nusselt Number in Water/Carbon Nanofluid [Volume 53, Issue 1, 2021, Pages 209-220]
C
Chahardowli, Mohammad Modeling of Drilling Cuttings Transport by Foam in Horizontal Well Condition Using Computational Fluid Dynamics [Volume 53, Issue 1 (Special Issue), 2021, Pages 357-374]
Chehardoli, Hossein Control of heterogeneous traffic flows in presence of pocket loss, time-varying communication delay and actuator lag [Volume 53, Issue 4, 2021, Pages 2155-2170]
Cheloee Darabi, Ali Investigation of the micromechanical behavior of ferritic-martensitic steel under complex loading [Volume 53, Issue 6, 2021, Pages 3689-3702]
Chidan, Adel Numerical Study of Natural Convection Heat Transfer inside a Triangular Cavity with Flexible Sidewalls Containing a Cylindrical Heat Source [Volume 53, Issue 11, 2022, Pages 5461-5484]
Choobdar Rahim, Farzad Investigation of Thermo-Hydraulic Parameters of Reactor Containment due to Cold-Leg Break Accident [Volume 53, Issue 3, 2021, Pages 1591-1606]
D
Dadashi, َAmin Experimental Study of Effects of Hydrogen Embrittlement and Residual Stress on Mechanical Properties of GTD450 [Volume 53, Issue 12, 2022, Pages 5659-5678]
Dadvand, Abdolrahman Numerical simulation of droplet formation in a T-shape microchannel using two-phase level-set method [Volume 53, Issue 3 (Special Issue), 2021, Pages 1815-1838]
Daghighi, Maziyar Out-of-Plane Vibration Mitigation of Wind Turbine Blade Using Highly Efficient Nonlinear Energy Sink [Volume 53, Issue 12, 2022, Pages 5851-5866]
DANANDEH OSKUEI, HOJJAT Investigating the Fluid-Solid Interaction in Incompressible Flow and The Effect of Oscillation Amplitude on Heat Transfer [Volume 53, Issue 9, 2021, Pages 4747-4772]
Daneshmand, Hamid Effect of Graphene Sheets Aggregation on The Dislocation-Blocking Mechanism of Nanolaminated Aluminum/Graphene Composite: Molecular Dynamics Simulation Study [Volume 53, Issue 8, 2021, Pages 4649-4664]
Darmohammadi, Anis Study of the Motion Behavior of Soft Fiber Reinforced Actuators Based on Fiber Angle [Volume 53, Issue 8, 2021, Pages 4565-4580]
Dashti, Isar Numerical Simulation of Variable Conductance Heat Pipe with Cold Reservoir by Single Phase Flow Approach [Volume 53, Issue 9, 2021, Pages 4905-4924]
Dashti Rahmat Abadi, Vahideh Investigation of Geometric Characteristics on the Non-Reaction Supersonic Flow inside the Channel with the Presence of Cavities [Volume 53, Issue 11, 2022, Pages 5409-5428]
Davoodabadi, Ali Prognostics of rolling element bearings using shock pulse method and vibration method records and employing feedforward neural-network [Volume 53, Issue 4 (Special Issue), 2021, Pages 2557-2576]
Davoodi, Farzin Effect of Gender and Body Fitness on the Thermal Sensation of Sleeping Occupants Under Task-Ambient Air Conditioning System [Volume 53, Issue 1 (Special Issue), 2021, Pages 453-466]
Dehestani, Mehdi Mechanical Properties and Structural Behavior of Bone at Nano Scale with Cohesive Element [Volume 53, Issue 2, 2021, Pages 745-776]
Dehghan, Ali Akbar Numerical Analysis of Parameters Affecting Turbulent Boundary Layer Trailing-Edge Noise [Volume 53, Issue 1 (Special Issue), 2021, Pages 437-452]
Dehghan, Ali Akbar Experimental Investigation of the Performance of Trailing Edge Noise-Reducing Finlets [Volume 53, Issue 9, 2021, Pages 4827-4846]
Dehghani Mohammadabadi, Mostafa The Feasibility Study of a Night Sky Radiative Cooling System for Cooling the Intake Air of a Gas Turbine [Volume 53, Issue 1, 2021, Pages 155-172]
E
Ebrahimi, Masood Techno-Economic Feasibility of Energy Supply Systems from Renewable Sources of Solar and Biomass in Rural Areas Located In Cold and Dry Climate [Volume 53, Issue 1, 2021, Pages 81-100]
Ebrahimi, Tina Numerical Investigation of Scour Around a Cylindrical Pier in Laboratory Scale Using Euler-Lagrange Approach [Volume 53, Issue 1 (Special Issue), 2021, Pages 411-426]
Ebrahimi Naghani, Peyman Experimental investigation of personalized ventilation effects on temperature, velocity, and draught discomfort distribution in an office [Volume 53, Issue 7, 2021, Pages 4397-4410]
Edalati, Saeed Energy and Exergy Analysis of Organic Rankine Cycle Fed by Electric Arc Furnace Waste Heat [Volume 53, Issue 9, 2021, Pages 4999-5016]
Eftekhari, Malihe Stability and bifurcation of a rotating blade with varying speed [Volume 53, Issue 4 (Special Issue), 2021, Pages 2459-2472]
Eftekhari, Mojtaba Stability and bifurcation of a rotating blade with varying speed [Volume 53, Issue 4 (Special Issue), 2021, Pages 2459-2472]
Eghbali, MohammadReza Free vibration of axially functionally graded nanobeam with an attached mass based on nonlocal strain gradient theory via new ADM numerical method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1159-1178]
Ehsani, Mohammad Modeling of vibro-acoustic modulation induced by non-linear contact in the Euler-Bernoulli beam using the Fourier spectral element [Volume 53, Issue 6 (Special Issue), 2021, Pages 3809-3824]
Ehsaniseresht, Abbas Stability analysis and snap-through evaluation of the cable-driven continuum robots [Volume 53, Issue 4, 2021, Pages 2089-2104]
Ehyaei, Amir Farhad Double Hyperbolic Sliding Mode Control Based on Unscented Kalman Filter for Three-legged Mobile manipulator [Volume 53, Issue 4, 2021, Pages 2105-2116]
Einolghozati, Mona Effect of microstructure features on the mechanical properties of spheroidized steel by crystal plasticity method. [Volume 53, Issue 6 (Special Issue), 2021, Pages 4079-4094]
Emamian, Amin Analytical Solution of Heat Transfer in a Cone Made of Functionally Graded Material [Volume 53, Issue 1 (Special Issue), 2021, Pages 539-552]
Esfahanian, Vahid Investigation of vehicle energy demand considering the modified tire power loss [Volume 53, Issue 6, 2021, Pages 3615-3628]
E. Torkanpouri, Kaveh Global sensitivity analysis of nanomachining parameters by using dynamic scanning thermal microscope [Volume 53, Issue 4, 2021, Pages 2367-2384]
Ettefagh, Mir Mohammad Identification and damage detection of beam-like structure using vibration signals based on simulated model, real healthy state and deep convolutional neural network [Volume 53, Issue 4, 2021, Pages 2193-2216]
Ettefagh, Mir Mohammad Damage detection of offshore jacket structure using dynamic responses based on simulated model, intact state of real model and deep auto-encoder neural network [Volume 53, Issue 6 (Special Issue), 2021, Pages 3783-3808]
Ettehadi, Hossein Development of Blade Element Momentum Theory for Unsteady Flow with Regard to the Dynamic Stall Phenomenon [Volume 53, Issue 3, 2021, Pages 1439-1456]
Ezzatneshan, Eslam Studying of droplet impingement on hydrophilic and hydrophobic curved surfaces by lattice Boltzmann method based on Allen-Cahn equation [Volume 53, Issue 5, 2021, Pages 2869-2886]
Ezzatneshan, Eslam Study of cavitation inception using multiphase lattice Boltzmann method with incorporating equations of state [Volume 53, Issue 5 (Special Issue), 2021, Pages 3151-3170]
F
Fahimi Farzam, Maziar Experimental and numerical study of energy harvesting from sloshing of a liquid and its performance on shaper machine [Volume 53, Issue 6 (Special Issue), 2021, Pages 3911-3924]
Fahmideh, Vahid Thermal performance evaluation of a greenhouse solar dryer equipped with photovoltaic cells and phase change material [Volume 53, Issue 5 (Special Issue), 2021, Pages 3367-3384]
Fakhari, Mohammad Mahdi Numerical analysis of distinction boundary of surface roughness and wall blocks in laminar pressure-driven flow within the rugged microchannels [Volume 53, Issue 5 (Special Issue), 2021, Pages 3241-3256]
Fakhari, Vahid Employing of shunt damping method to reduce edgewise vibration of small size wind turbine blade with considering the effect of vibration coupling [Volume 53, Issue 4, 2021, Pages 2073-2088]
Fakharian, Ahmad Nonlinear optimal control of an active transfemoral prosthesis using state dependent Riccati equation approach [Volume 53, Issue 4, 2021, Pages 2117-2136]
Fallah, Mohsen Advanced exergy and thermoeconomic analysis of the supercritical carbon dioxide recompression cycle: A comparative study [Volume 53, Issue 5, 2021, Pages 2967-2982]
Fallah, Mohsen Piezoelectric Energy Harvesting Using a Porous Beam Under Fluid-Induced Vibrations [Volume 53, Issue 8, 2021, Pages 4633-4648]
Fanaei Sheikholeslami, Tahereh Fabrication and characterization of a flexible nanogenerator using reverse electrowetting concept [Volume 53, Issue 5, 2021, Pages 3023-3034]
Fanaei Sheikholeslami, Tahereh Design and Multi-Objective Optimization of A Magnetohydrodynamic Drug Delivery Infusion Micropump [Volume 53, Issue 10, 2022, Pages 5221-5238]
Farahani, Mohammadreza Condition monitoring of defective single lap adhesive joint using carbon nanotubes [Volume 53, Issue 2 (Special Issue), 2021, Pages 1321-1330]
Farahani, Somayeh Real Time Solution for Inverse Heat Conduction Problem in One-Dimensional Plate Utilizing Fuzzy- Proportional–Integral–Derivative Controller [Volume 53, Issue 1, 2021, Pages 303-316]
Farahat, Said The Feasibility Study of a Night Sky Radiative Cooling System for Cooling the Intake Air of a Gas Turbine [Volume 53, Issue 1, 2021, Pages 155-172]
Farahat, Said Numerical study and investigation of the effect of magnetic field on fluid hydrodynamic behavior [Volume 53, Issue 5, 2021, Pages 2857-2868]
Farahnakian, Masoud Experimental investigation of the infeed method and machining parameters on the tool wear during thread milling [Volume 53, Issue 2 (Special Issue), 2021, Pages 1345-1356]
Fardi, Amirhossein Improving the power coefficient of the Darrieus vertical axis wind turbine with the aid of morphing airfoils [Volume 53, Issue 5 (Special Issue), 2021, Pages 3227-3240]
Fardi, Amirhossein Improvement of aerodynamic coefficients of the airfoil with free form deformation with the aid of Artificial Neural Networks and Genetic Algorithm [Volume 53, Issue 7, 2021, Pages 4113-4132]
Faridzadeh, Maryam Laser Cladding of TiC/316LSS and Analysis of Input Parameters using Response Surface Method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1269-1286]
Farmahini farahani, Moein Analytical model for the non-premixed combustion of the titanium dust cloud in counter-flow geometry [Volume 53, Issue 5 (Special Issue), 2021, Pages 3307-3316]
Farrokhi, Navid Experimental Study of the Effects of Fluid Physical Properties and Working Temperature on Heat Transfer in Conduction Pump [Volume 53, Issue 3, 2021, Pages 1607-1620]
Farshchi, Mohammad Influence of Pseudo-Boiling Phenomenon and the Mass Flux Ratio on the Dynamics of Transcritical Shear Flame [Volume 53, Issue 9, 2021, Pages 4961-4980]
Farsi, Mohammad Ali Fatigue crack growth analysis via Wiener degradation model with random effects [Volume 53, Issue 4, 2021, Pages 2271-2286]
Farsi, Mohammad Ali Reliability analysis of rectangular plate under in-plane tensile loading using continuum damage mechanics theory [Volume 53, Issue 6, 2021, Pages 3645-3656]
Fatahi, Laleh Numerical Simulation of Liner Vibrations in a Laboratory Combustion Chamber [Volume 53, Issue 2, 2021, Pages 881-896]
Fathian, Ashkan Study of the Motion Behavior of Soft Fiber Reinforced Actuators Based on Fiber Angle [Volume 53, Issue 8, 2021, Pages 4565-4580]
Fattahi, Ayoub Studying of droplet impingement on hydrophilic and hydrophobic curved surfaces by lattice Boltzmann method based on Allen-Cahn equation [Volume 53, Issue 5, 2021, Pages 2869-2886]
Fazelzadeh Haghighi, S. Ahmad Modeling and Flutter Analysis of a Three Dimensional Box-Wing using Wagner Unsteady Aerodynamic Model [Volume 53, Issue 12, 2022, Pages 5809-5830]
Fazli, Mohamad An Improved Failure Modes and Effects Analysis as a New Framework to perform the Function Analysis Phase of products in the Value Engineering [Volume 53, Issue 8, 2021, Pages 4665-4690]
Felegari, Ali Haidar Actuators redundancy resolution scheme with computational time reduction purpose for parallel cable robots with considering the rupture limits of the cables [Volume 53, Issue 6, 2021, Pages 3479-3496]
Feli, Saeid A study on the synergistic influence of reduced graphene oxide and MWCNTs on the mechanical properties of epoxy nanocomposite [Volume 53, Issue 6 (Special Issue), 2021, Pages 3971-3986]
Ferasat, Reza Stability Analysis of Predictive Control in Networked Control System Using Switching Control [Volume 53, Issue 10, 2022, Pages 5039-5054]
Fili, Milad Design and evaluation of a novel bi-evaporator combined power and refrigeration cycle working with various zeotropic mixtures [Volume 53, Issue 5, 2021, Pages 3003-3022]
Firoozzadeh, Mohammad An Experimental Investigation on the Convective Heat Transfer Coefficient and Nusselt Number in Water/Carbon Nanofluid [Volume 53, Issue 1, 2021, Pages 209-220]
Foadaddini, Ali Effect of Gender and Body Fitness on the Thermal Sensation of Sleeping Occupants Under Task-Ambient Air Conditioning System [Volume 53, Issue 1 (Special Issue), 2021, Pages 453-466]
Foadaddini, Ali Developing an alternating direction explicit-implicit domain-decomposition approach to solve heat transfer equation on graphics processing unit [Volume 53, Issue 3 (Special Issue), 2021, Pages 1915-1936]
Foroutan, Kamran Superharmonic and Subharmonic Resonance Analysis of A Rectangular Hyperelastic Membrane Resting on Nonlinear Elastic Foundation Using The Method of Multiple Scales [Volume 53, Issue 8, 2021, Pages 4535-4564]
Fouladi, Nematollah Numerical Analysis of Cross Section Time Variation Effects of the Supersonic Exhaust Diffuser [Volume 53, Issue 3, 2021, Pages 1469-1486]
G
Gandomkar, mohammad Variable distance interdigitated electrodes design to improve the performance of cantilever piezoelectric thin films nanogenerators [Volume 53, Issue 4, 2021, Pages 2347-2366]
Gandomkar, Mohammad Numerical simulation of salt gradient solar pond by employing the solar radiation estimating function considering wall-shading effects [Volume 53, Issue 5 (Special Issue), 2021, Pages 3385-3400]
Ganjiani, Seyed Mahdi Numerical Simulation of Elastoplastic Behavior and Damage Evolution at Various Stress Triaxiality [Volume 53, Issue 12, 2022, Pages 5703-5724]
Garousi, Leili Energy, Exergy and Economic Analysis of a Semi-solar Greenhouse with Experimental Validation [Volume 53, Issue 3, 2021, Pages 1677-1694]
Gavagsaz-ghoachani, Roghayeh Experimental study on effective parameters on vertical axis wind turbine performance [Volume 53, Issue 5, 2021, Pages 2771-2790]
Ghader, Sarmad Diagnostical and observational analysis of clear air turbulence over the middle east and Iran [Volume 53, Issue 7, 2021, Pages 4203-4220]
Ghaderi, Seyed Hadi Crystal Plasticity Finite Element Study of Necking Behavior of Aluminum Alloy Sheet Subject to Thickness-Stress [Volume 53, Issue 12, 2022, Pages 5755-5768]
Ghadimi, Zahra Accurate Calculation of Nodal Vectors in Isogeometric Analysis of Shell Structures Using Greville Points [Volume 53, Issue 10, 2022, Pages 5185-5202]
Ghaebi, Hadi Design and evaluation of a novel bi-evaporator combined power and refrigeration cycle working with various zeotropic mixtures [Volume 53, Issue 5, 2021, Pages 3003-3022]
Ghaedamini, Morteza Investigation of the Humidifier Performance of Adding Gas Diffusion Layers Around Membrane for Fuel Cell Application [Volume 53, Issue 3, 2021, Pages 1653-1666]
Ghafarirad, Hamed Kinematic Modeling of a Spatial Soft Robot by an Improved Analytical Method Based on Serial Robots [Volume 53, Issue 2 (Special Issue), 2021, Pages 1065-1080]
Ghaf-Ghanbari, Pegah Kinematic and dynamic performance evaluation of a four degrees of freedom parallel robot [Volume 53, Issue 4, 2021, Pages 2055-2072]
Ghafouri, Ashkan Numerical simulation of heat transfer and pressure drop of pseudo-plastic fluid in a pipe heat exchanger equipped with a modified twisted tape [Volume 53, Issue 5, 2021, Pages 3077-3098]
Ghafurian, Mohammad Mustafa Steam generation via solar energy and localizing the light on the pinewood surface [Volume 53, Issue 3 (Special Issue), 2021, Pages 2001-2012]
Ghalambaz, Mohammad Investigation of Heat Transfer of Non-Newtonian Pseudo-Plastic Fluids in Porous Heat Exchangers [Volume 53, Issue 1, 2021, Pages 241-258]
Ghannad, Mahdi 2-Dimensional Electroelastic Analysis of Piezoelectric Cylinders Using First-Order Shear Deformation and First-Order Electric Potential Theories [Volume 53, Issue 2, 2021, Pages 815-832]
Ghannad, Mehdi Effect of adding carbon nanotubes into the matrix material on the buckling behavior of glass/epoxy composite plates: An experimental study [Volume 53, Issue 4 (Special Issue), 2021, Pages 2613-2628]
Ghasemi, Ali Attitude Stabilization of Quadrotor Using Adaptive Fuzzy Proportional Integral Derivative Controller [Volume 53, Issue 2 (Special Issue), 2021, Pages 1081-1094]
Ghasemi, behzad Numerical Study of Natural Convection Heat Transfer inside a Triangular Cavity with Flexible Sidewalls Containing a Cylindrical Heat Source [Volume 53, Issue 11, 2022, Pages 5461-5484]
Ghasemikaram, Amirhossein Modeling and Flutter Analysis of a Three Dimensional Box-Wing using Wagner Unsteady Aerodynamic Model [Volume 53, Issue 12, 2022, Pages 5809-5830]
Ghasemi Kordlar, Amir Vertical growth of titanium dioxide nanorods on nebulizer fluorine doped tin oxide deposited on silicon microarrays [Volume 53, Issue 6 (Special Issue), 2021, Pages 4051-4062]
Ghasemzadeh Moghadam, Mojtaba Numerical Investigation of the Effect of Shell Material and Thickness on the Mechanics of Motorcycle Helmets Impact [Volume 53, Issue 2, 2021, Pages 687-708]
Ghasimi, Seyed Danial Fluid-Structure Interactions Analysis of Tension in An Axon Using Finite Elements Modeling to Investigate Strain Related Neurological Damages [Volume 53, Issue 8, 2021, Pages 4609-4632]
Ghiasvand, Amir Numerical investigation and prediction of grain size in different friction stir welding areas of AA6061 aluminum alloy [Volume 53, Issue 6, 2021, Pages 3751-3760]
Ghoddosian, Ali Torque minimization of 2-DOF parallel robot using counterweights and trajectory planning [Volume 53, Issue 4 (Special Issue), 2021, Pages 2409-2422]
Ghoddosian, Ali A new optimal structural boundary modification algorithm in the multi-objective topology optimization of microgripper [Volume 53, Issue 4, 2021, Pages 2261-2270]
Ghogha, hamid Experimental investigation of the infeed method and machining parameters on the tool wear during thread milling [Volume 53, Issue 2 (Special Issue), 2021, Pages 1345-1356]
Gholami, Peyman Fatigue crack growth analysis via Wiener degradation model with random effects [Volume 53, Issue 4, 2021, Pages 2271-2286]
Gholami, Peyman Reliability analysis of rectangular plate under in-plane tensile loading using continuum damage mechanics theory [Volume 53, Issue 6, 2021, Pages 3645-3656]
Gholipour, Hamed Network Modeling to Investigate the Effect of Coupling the Transport Phenomena on Water Distribution in Gas Diffusion Layer [Volume 53, Issue 11, 2022, Pages 5505-5528]
Ghoolipour, Hamed Micromechanical Damage Model for Plasticity of Metals to Predict Failure under Shear Loads [Volume 53, Issue 12, 2022, Pages 5679-5702]
Ghoreishi, Seyyed Alireza Double Hyperbolic Sliding Mode Control Based on Unscented Kalman Filter for Three-legged Mobile manipulator [Volume 53, Issue 4, 2021, Pages 2105-2116]
Golaghapour Kami, Meysam Dynamic analysis of cylindrical sandwich shell with orthogonal stiffeners using high-order theory [Volume 53, Issue 4 (Special Issue), 2021, Pages 2473-2492]
Golzari, Masoud Sound Transmission Loss of Truncated Conical Shells with Porous Materials [Volume 53, Issue 2, 2021, Pages 923-942]
Goodarzi, Mohmmadreza Effects of air injection at rotor blade row tip region of an axial compressor on its performance under inlet distortion conditions [Volume 53, Issue 3 (Special Issue), 2021, Pages 1729-1744]
Gorji, Mohammad-Mahdi Numerical Simulation of Variable Conductance Heat Pipe with Cold Reservoir by Single Phase Flow Approach [Volume 53, Issue 9, 2021, Pages 4905-4924]
Goshayeshi, Hamidreza Experimental investigation on MWCNTs-COOH nano fluid on 3D oscillating heat pipe [Volume 53, Issue 5 (Special Issue), 2021, Pages 3401-3416]
Goudarzi, Masoud Experimental and Numerical Looseness Detection and Assessment in Flanged Joints Using Vibro-Acoustic Modulation Method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1331-1344]
H
Habibnejad korayem, Moharam Path Design and Control of a Moving Social Robot in an Environment with Moving Obstacles in Order to Reach a Moving Target through Fuzzy Control [Volume 53, Issue 2, 2021, Pages 993-1014]
Habibnezhad Ledari, Behnam Experimental Investigation on the Thermal Resistance of Straight Heat Pipes with Double-Ended Cooling and Middle-Heating at Different Tilt Angles [Volume 53, Issue 1, 2021, Pages 279-302]
Haghani, Seyyed Omid Numerical simulation simultaneous use of longitudinal ventilation and smoke extraction from the ceiling in fires inside tunnels [Volume 53, Issue 7, 2021, Pages 4411-4428]
Haghi, Seyed Behzad Investigation of hydrogen production process by partial oxidation of natural gas in a large non-catalytic reformer and comparison with methane steam reforming process in a small catalytic reformer [Volume 53, Issue 5 (Special Issue), 2021, Pages 3275-3292]
Hajiahmadi, Farima Dynamic modeling and control of cleaning robot for agro-photovoltaic [Volume 53, Issue 6, 2021, Pages 3465-3478]
Hajlotfalian, Mostafa Three-dimensional surface capture from the back anatomy to quantify three-dimensional vertebral column curvatures without using anatomical markers [Volume 53, Issue 4 (Special Issue), 2021, Pages 2629-2638]
Hakkaki-Fard, Ali Comparison of long-term performance and the initial cost of the horizontal ground source heat pump with the air source heat pump in hot regions [Volume 53, Issue 5 (Special Issue), 2021, Pages 3317-3334]
Hamed, Mohammad Ali Control of Vehicle’s Mixed Longitudinal and Lateral Stability with Engine Dynamics Using Super Twisting Control Algorithm [Volume 53, Issue 2, 2021, Pages 959-978]
Hamedi, Mohammad Hosein Image-based numerical model for drug delivery to solid tumors [Volume 53, Issue 5 (Special Issue), 2021, Pages 3187-3200]
Hamidi, Mehdi Numerical Investigation of Scour Around a Cylindrical Pier in Laboratory Scale Using Euler-Lagrange Approach [Volume 53, Issue 1 (Special Issue), 2021, Pages 411-426]
Hasanabadi, Ehsan A new optimal structural boundary modification algorithm in the multi-objective topology optimization of microgripper [Volume 53, Issue 4, 2021, Pages 2261-2270]
Hasanvand, Nima Analytical model for the non-premixed combustion of the titanium dust cloud in counter-flow geometry [Volume 53, Issue 5 (Special Issue), 2021, Pages 3307-3316]
Hashemi, Seyed mohammad rezs Experimental and Numerical Investigation of Fatigue Behavior of Polylactic acid Components Made by Additive Manufacturing Method [Volume 53, Issue 6, 2021, Pages 3703-3716]
Hashemian, Seyed Ali Numerical Investigation of the Effect of Shell Material and Thickness on the Mechanics of Motorcycle Helmets Impact [Volume 53, Issue 2, 2021, Pages 687-708]
Hasheminasab, Mohammadreza Simulation, manufacturing and test of a transparent proton-exchange membrane fuel cell [Volume 53, Issue 3 (Special Issue), 2021, Pages 2031-2052]
Hashemi-Pour Moosavi, Shahin Stability analysis and snap-through evaluation of the cable-driven continuum robots [Volume 53, Issue 4, 2021, Pages 2089-2104]
Hashemi Tari, Pooyan Experimental study on effective parameters on vertical axis wind turbine performance [Volume 53, Issue 5, 2021, Pages 2771-2790]
Hashemi Tari, Pooyan Wind simulation in a complex terrain by numerical weather prediction method using large eddy simulation [Volume 53, Issue 7, 2021, Pages 4221-4240]
Hassanbeigi, Reza Dynamic modeling and control of cleaning robot for agro-photovoltaic [Volume 53, Issue 6, 2021, Pages 3465-3478]
Hassani, Behrouz Accurate Calculation of Nodal Vectors in Isogeometric Analysis of Shell Structures Using Greville Points [Volume 53, Issue 10, 2022, Pages 5185-5202]
Hassani, Maryam Two-dimensional simulation of nucleation pool boiling and investigation of phase change mechanism at low heat fluxes [Volume 53, Issue 3 (Special Issue), 2021, Pages 1883-1896]
Hassanzadeh, Hasan Effect of Gender and Body Fitness on the Thermal Sensation of Sleeping Occupants Under Task-Ambient Air Conditioning System [Volume 53, Issue 1 (Special Issue), 2021, Pages 453-466]
Hassanzadeh, Rahim Investigation of the effect of free-wind velocity on the performance of small-scale vertical axis wind turbine [Volume 53, Issue 3 (Special Issue), 2021, Pages 1709-1728]
Hataminasab, Mohsen Numerical Analysis of Cross Section Time Variation Effects of the Supersonic Exhaust Diffuser [Volume 53, Issue 3, 2021, Pages 1469-1486]
Hayeri Yazdi, Mohammad Reza Investigation of vehicle energy demand considering the modified tire power loss [Volume 53, Issue 6, 2021, Pages 3615-3628]
Hayeri Yazdi, Mohammad Reza Investigation of wave propagation in architected uniform triangle mass center fractal nano-bio-filters based on microtubules [Volume 53, Issue 6 (Special Issue), 2021, Pages 3939-3952]
Hedayatizadeh, Mahdi Thermal performance evaluation of a greenhouse solar dryer equipped with photovoltaic cells and phase change material [Volume 53, Issue 5 (Special Issue), 2021, Pages 3367-3384]
Heidarinejad, Ghassem The Effect of Inner Walls Reflection on Microorganisms Inactivation in Water Ultraviolet Reactor using computational fluid dynamics [Volume 53, Issue 1 (Special Issue), 2021, Pages 375-392]
Heidarinejad, Ghassem Dynamic Simulation of Desiccant Cooling System with Simultaneously Using Solar and Ground Renewable Energies in Hot-Humid Regions [Volume 53, Issue 3, 2021, Pages 1549-1572]
Heidarinejad, Ghassem Temporal analysis of the fistula at three anastomosis angles of 45, 90, and 135 degrees [Volume 53, Issue 3 (Special Issue), 2021, Pages 1799-1814]
Heidarinejad, Ghassem Numerical investigation of compartment fire under maximum and minimum of natural ventilation using flamelet generated manifold combustion model [Volume 53, Issue 5 (Special Issue), 2021, Pages 3335-3350]
Heidari Soreshjani, Masoud A numerical investigation on the effect of blade tip shapes on power generation of a horizontal axis wind turbine [Volume 53, Issue 5, 2021, Pages 2791-2806]
Heinrich, Martin Circumferential Casing Treatment in a Transonic Fan [Volume 53, Issue 7, 2021, Pages 4189-4202]
Heinrich, Martin A Theory for Predicting Stall Cell Transient Behavior [Volume 53, Issue 9, 2021, Pages 4773-4788]
Heshmati, Mahmood A study on the synergistic influence of reduced graphene oxide and MWCNTs on the mechanical properties of epoxy nanocomposite [Volume 53, Issue 6 (Special Issue), 2021, Pages 3971-3986]
Heydari, Mohammad Hosein Fractional calculus approach for bending of viscoelastic plate using two-variable refined plate theory [Volume 53, Issue 4, 2021, Pages 2287-2308]
Hojaji, Mohammad Numerical/Experimental Investigation of the Presence of a Protuberance in a Convergent – Divergent Nozzle in Supersonic Regime to Control the Thrust Vector [Volume 53, Issue 9, 2021, Pages 4887-4904]
Honarvar, Mohammad Hadi Three-dimensional surface capture from the back anatomy to quantify three-dimensional vertebral column curvatures without using anatomical markers [Volume 53, Issue 4 (Special Issue), 2021, Pages 2629-2638]
Hooshmand, Seyed Mohammad Effect of Air Curtain on Occupants Thermal Comfort and Indoor Air Quality in an Athletic Swimming Pool with Spectators’ Stand [Volume 53, Issue 1, 2021, Pages 191-208]
Hooshmand, Seyed Mohammad Effect of Gender and Body Fitness on the Thermal Sensation of Sleeping Occupants Under Task-Ambient Air Conditioning System [Volume 53, Issue 1 (Special Issue), 2021, Pages 453-466]
Hooshmand, Seyed Mohammad Experimental evaluation of the effect of supply air direction on air current and temperature in a room with underfloor air distribution system [Volume 53, Issue 5, 2021, Pages 3057-3076]
Hossein Farrash, Seyed Mahdi Effect of adding carbon nanotubes into the matrix material on the buckling behavior of glass/epoxy composite plates: An experimental study [Volume 53, Issue 4 (Special Issue), 2021, Pages 2613-2628]
Hossein Farrash, Seyed Mahdi An experimental investigation of the effect of the type of nanostructured reinforcements on the mechanical and tribological properties of epoxy based nanocomposites [Volume 53, Issue 6 (Special Issue), 2021, Pages 4009-4022]
Hosseini, Seyyed Amirhosein Free vibration of axially functionally graded nanobeam with an attached mass based on nonlocal strain gradient theory via new ADM numerical method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1159-1178]
Hosseini, Shahram Nonlinear analysis of hyperelastic plates using first-order shear deformation plate theory and a meshless method [Volume 53, Issue 4, 2021, Pages 2331-2346]
Hosseini Mansoub, Farid Analysis of Forming Limit of Sheet Metals Considering Vertex Localized Necking and Ductile Damage Criterion [Volume 53, Issue 2 (Special Issue), 2021, Pages 1307-1320]
Hosseini-Toudeshky, Hossein Micro-Mechanical Damage Analysis of Al-TiC Particulate Reinforced Composites by Peridynamic Theory [Volume 53, Issue 8, 2021, Pages 4701-4716]
Houshfar, Ehsan Investigation on the effect of addition of nano-titanium oxide particles to phase change material in a hybrid system for battery cooling under constant heat flux [Volume 53, Issue 7, 2021, Pages 4379-4396]
I
Irani, Saeid Investigation of Nonlinear Vibrations of A Cantilever Beam with A Transverse Fatigue Crack [Volume 53, Issue 10, 2022, Pages 5069-5084]
J
Jaafarian Kafshgary, Naghmeh Fault Detection of journal bearings and Simulation of Major Occurred Fault using Failure Mode and Effect Analysis Method to Evaluate its Effects [Volume 53, Issue 8, 2021, Pages 4581-4594]
Jaberi, Amin Experimental Investigation of a High Aspect Ratio Rectangular Liquid Jet in Parallel Airflow [Volume 53, Issue 11, 2022, Pages 5429-5444]
Jadidi, Amir Mohammad Investigating the Effects of Loung Chair Fire in a Cinema Hall Using Displacement, Impingement Jet and Stratum Ventilation Systems [Volume 53, Issue 11, 2022, Pages 5573-5594]
Jafari, Hamid Investigation of wave propagation in architected uniform triangle mass center fractal nano-bio-filters based on microtubules [Volume 53, Issue 6 (Special Issue), 2021, Pages 3939-3952]
Jafari, Mohammad An experimental investigation of the effect of the type of nanostructured reinforcements on the mechanical and tribological properties of epoxy based nanocomposites [Volume 53, Issue 6 (Special Issue), 2021, Pages 4009-4022]
Jafari, Moharram Thermodynamic Analysis of Power Generation System Based on Solid Oxide Fuel Cell With External Reforming [Volume 53, Issue 1 (Special Issue), 2021, Pages 605-622]
Jafari, Moharram Experimental Study of the Effects of Fluid Physical Properties and Working Temperature on Heat Transfer in Conduction Pump [Volume 53, Issue 3, 2021, Pages 1607-1620]
Jafarkazemi, Farzad Theoretical comparison of thermal and electrical performance of different models of sheet and tube type solar photovoltaic - thermal water collector [Volume 53, Issue 5, 2021, Pages 2903-2920]
Jafarmadar, Samad Thermo-Economic Evaluation of a Power and Freshwater Production System Including a Liquid Metal Magnetohydrodynamic Unit Driven By a Concentrated Solar Tower and Biogas [Volume 53, Issue 11, 2022, Pages 5551-5572]
Jahanbakhshi, Akram Effects of Magnetic Field on Natural Convection of Non-Newtonian Fluid in a Square Enclosure with a Central Heat Source [Volume 53, Issue 1, 2021, Pages 259-278]
Jahangirian, Alireza A numerical investigation on the effect of blade tip shapes on power generation of a horizontal axis wind turbine [Volume 53, Issue 5, 2021, Pages 2791-2806]
Jahanshahi Javaran, ٍEbrahim Thermodynamic and Thermo-Economic Analysis of the Absorption Heat Transformer, Organic Rankine Cycle, and Reverse Osmosis Desalination Combined System [Volume 53, Issue 1 (Special Issue), 2021, Pages 639-654]
Jalaly, Maisam A Study on the Ballistic Behavior of Kevlar Fabric Impregnated with Shear Thickening Fluid Containing Graphene Oxide Additive [Volume 53, Issue 12, 2022, Pages 5725-5738]
Jamali, Ali Designing Optimum Multi-Domain System by Integrating Bond Graph and Genetic Programming [Volume 53, Issue 2, 2021, Pages 1015-1038]
Jamialahmadi, Amir Ahmad Experimental study of CuO/Water nanofluid pool boiling on the copper flat surface and measurement of the critical heat flux [Volume 53, Issue 5, 2021, Pages 3099-3114]
Jamshidi, Kamal A comparison study of deep neural controllers and classic controllers in self-driving car application [Volume 53, Issue 4 (Special Issue), 2021, Pages 2439-2458]
Javadi, Aliyar Simulation of a Photocatalytic Reactor Using Finite Volume and Discrete Ordinate Method: A Parametric Study [Volume 53, Issue 1 (Special Issue), 2021, Pages 573-588]
Javadi, Seyed Mohammad Numerical study and investigation of the effect of magnetic field on fluid hydrodynamic behavior [Volume 53, Issue 5, 2021, Pages 2857-2868]
Javaherdeh, Kourosh Numerical Simulation of Heat Transfer Turbulent Flow for Non-Newtonian Nanofluid in a Double Pipe Helical Heat Exchanger [Volume 53, Issue 1, 2021, Pages 221-240]
JavanNezhad, Reza Diagnostical and observational analysis of clear air turbulence over the middle east and Iran [Volume 53, Issue 7, 2021, Pages 4203-4220]
Jodat, Amin Experimental Study of Injecting Water Vapor and Oil Compounds by Nebulizer on the Efficiency and Natural Gas Flame Pollution [Volume 53, Issue 1, 2021, Pages 31-40]
K
Kadkhodapour, Javad Investigation of the micromechanical behavior of ferritic-martensitic steel under complex loading [Volume 53, Issue 6, 2021, Pages 3689-3702]
Kadkhodayan, Mehran Theoretical Analysis of Equal Channel Angular Pressing Process by Upper Bound Method and Its Experimental Investigation in Condition of Circular Cross-Section Channel [Volume 53, Issue 8, 2021, Pages 4729-4744]
Kamari, Djavad Implementation of Continuous Blowing and Synthetic Jet Actuators to Control the Flow Separation over a Fully Stalled Airfoil [Volume 53, Issue 9, 2021, Pages 4847-4864]
Kargar Daroonkolaee, Mohammadreza Crystal Plasticity Finite Element Study of Necking Behavior of Aluminum Alloy Sheet Subject to Thickness-Stress [Volume 53, Issue 12, 2022, Pages 5755-5768]
Karimi, meysam Effect of Graphene Sheets Aggregation on The Dislocation-Blocking Mechanism of Nanolaminated Aluminum/Graphene Composite: Molecular Dynamics Simulation Study [Volume 53, Issue 8, 2021, Pages 4649-4664]
Karimi, Sina Superharmonic and Subharmonic Resonance Analysis of A Rectangular Hyperelastic Membrane Resting on Nonlinear Elastic Foundation Using The Method of Multiple Scales [Volume 53, Issue 8, 2021, Pages 4535-4564]
Karimi Rastehkenari, Zohreh Denoising vibration signals of rotating machines using probability density function, similarity measure and improved thresholding function [Volume 53, Issue 4 (Special Issue), 2021, Pages 2493-2512]
Karimnejad, Sajjad Analytical Solution of Heat Transfer in a Cone Made of Functionally Graded Material [Volume 53, Issue 1 (Special Issue), 2021, Pages 539-552]
KARIMPOUR, morad Effect of 3D-Printing and Compression Molding on Anisotropy of Acrylonitrile Butadiene Styrene Micro Specimen: A Comparative Study Based on Digital Image Correlation [Volume 53, Issue 12, 2022, Pages 5645-5658]
Kashaniasl, Shahram Experimental study on the enhancement of the thermal efficiency of a household gas water heater [Volume 53, Issue 3 (Special Issue), 2021, Pages 2013-2030]
Kashi Parpinchi, Mohsen Simulation and Optimization of Rankine Power Generation Cycle Purposing the Efficiency of Liquefied Natural Gas Cold Exergy [Volume 53, Issue 1, 2021, Pages 117-134]
Kayhani, Mohammad Hasan Experimental study of CuO/Water nanofluid pool boiling on the copper flat surface and measurement of the critical heat flux [Volume 53, Issue 5, 2021, Pages 3099-3114]
Kayhani, Mohammad Hassan Manufacturing and Testing of an Optimized Magneto-Rheological Fluid and Modelling of a Twin Tube Magneto-Rheological Damper Using a Modified Non-Newtonian Model Using Analytical Quasi-Static, Analytical Unsteady, Numerical and Experimental Methods [Volume 53, Issue 3, 2021, Pages 1373-1400]
Kazemi, Mahdi Investigation of the effect of welding path on residual stresses and deformations in peripheral welding of steel pipe [Volume 53, Issue 4 (Special Issue), 2021, Pages 2735-2750]
Kazemi, Mahdi Numerical investigation and prediction of grain size in different friction stir welding areas of AA6061 aluminum alloy [Volume 53, Issue 6, 2021, Pages 3751-3760]
Kazemi, Mohsen Improving the power coefficient of the Darrieus vertical axis wind turbine with the aid of morphing airfoils [Volume 53, Issue 5 (Special Issue), 2021, Pages 3227-3240]
Kazemi, Mohsen Improvement of aerodynamic coefficients of the airfoil with free form deformation with the aid of Artificial Neural Networks and Genetic Algorithm [Volume 53, Issue 7, 2021, Pages 4113-4132]
Kazemi, Mostafa Optimization of The Slotted Gurney-Flap Geometry Applied to NACA 0012 Airfoil for Aerodynamic Performance Improvement [Volume 53, Issue 11, 2022, Pages 5331-5348]
Kazemzadeh-Parsi, Mohammad Javad Application of Nonconforming Quadtree Grids in the Finite Element Method [Volume 53, Issue 2, 2021, Pages 673-686]
Kazemzadeh-Parsi, Mohammad Javad Analytical Study on Effect of Loosening on Nonlinear Vibration Behavior of Bolted Joints [Volume 53, Issue 12, 2022, Pages 5739-5754]
Kazerooni, Mehrdad An Improved Failure Modes and Effects Analysis as a New Framework to perform the Function Analysis Phase of products in the Value Engineering [Volume 53, Issue 8, 2021, Pages 4665-4690]
Kermani, Mohammad J. Simulation, manufacturing and test of a transparent proton-exchange membrane fuel cell [Volume 53, Issue 3 (Special Issue), 2021, Pages 2031-2052]
Kermani, Mohammad J. Network Modeling to Investigate the Effect of Coupling the Transport Phenomena on Water Distribution in Gas Diffusion Layer [Volume 53, Issue 11, 2022, Pages 5505-5528]
Keymasi Khalaji, Ali Tracking control of quadrotors in the presence of obstacles based on potential field method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1095-1110]
Khajehzadeh, Mohsen Experimental study of machining residual stresses in plasma-assisted turning process [Volume 53, Issue 4, 2021, Pages 2385-2406]
Khajehzadeh, Mohsen Experimental Study of the Effect of Initial Surface Roughness on Ball Burnishing Forces and Endurance Limit of AISI 4130 Hardened Steel [Volume 53, Issue 12, 2022, Pages 5627-5644]
Khalafi, Vahid Flutter reliability analysis of laminated composite plates [Volume 53, Issue 6 (Special Issue), 2021, Pages 3925-3938]
Khalati, Parvaneh Removal of Lead Heavy Metal from Wastewater by Crystallization Process and Investigation of the Effective Parameters [Volume 53, Issue 11, 2022, Pages 5349-5366]
Khaleghi, Hassan Numerical investigation of ethanol and acetone spray injection into gaseous environment [Volume 53, Issue 5 (Special Issue), 2021, Pages 3213-3226]
Khaleghi, Hosein Circumferential Casing Treatment in a Transonic Fan [Volume 53, Issue 7, 2021, Pages 4189-4202]
Khaleghi, Hossein A Theory for Predicting Stall Cell Transient Behavior [Volume 53, Issue 9, 2021, Pages 4773-4788]
Khalilarya, Shahram Thermodynamic Analysis of a Novel Power, Cooling, Hydrogen and Oxygen Multi-Generation Combined Cycle Based on the Sabalan Geothermal Wells [Volume 53, Issue 1, 2021, Pages 135-154]
Khalilarya, Shahram Thermodynamic analysis and comparison of two new tri-generation (hydrogen, power, heating) systems using geothermal energy [Volume 53, Issue 5, 2021, Pages 2983-3002]
Khalilarya, Shahram Thermo-Economic Evaluation of a Power and Freshwater Production System Including a Liquid Metal Magnetohydrodynamic Unit Driven By a Concentrated Solar Tower and Biogas [Volume 53, Issue 11, 2022, Pages 5551-5572]
Khanaki, Mansour Simulation and Optimization of Rankine Power Generation Cycle Purposing the Efficiency of Liquefied Natural Gas Cold Exergy [Volume 53, Issue 1, 2021, Pages 117-134]
Khanaki, Mansour Techno-Economic Feasibility of Energy Supply Systems from Renewable Sources of Solar and Biomass in Rural Areas Located In Cold and Dry Climate [Volume 53, Issue 1, 2021, Pages 81-100]
Kharazan, Masoud Investigation of Nonlinear Vibrations of A Cantilever Beam with A Transverse Fatigue Crack [Volume 53, Issue 10, 2022, Pages 5069-5084]
Khatibi, Mohammad Mahdi Experimental verification of indirect bridge mode shape identification using transmissibility of a passing vehicle [Volume 53, Issue 6, 2021, Pages 3529-2548]
Khavasi, Ehsan Numerical Investigation of Scour Around a Cylindrical Pier in Laboratory Scale Using Euler-Lagrange Approach [Volume 53, Issue 1 (Special Issue), 2021, Pages 411-426]
Khavasi, Ehsan Numerical simulation of Holmboe waves in intrusive gravity current using LES method [Volume 53, Issue 7, 2021, Pages 4261-4278]
Khavasi, Ehsan Studying Wind Effect on the Hydrodynamic Behavior of Lock-Exchange Density Current [Volume 53, Issue 9, 2021, Pages 4807-4826]
Khayyati, HamidReza Thermal stress analysis for an aluminum die cast die [Volume 53, Issue 4 (Special Issue), 2021, Pages 2687-2702]
Khazaee, Mostafa Modeling, design and investigation of seat suspension based on negative stiffness structure to improve the vibration environment for helicopter pilots [Volume 53, Issue 4 (Special Issue), 2021, Pages 2513-2538]
Kheradmand, Saeed Investigation of Geometric Characteristics on the Non-Reaction Supersonic Flow inside the Channel with the Presence of Cavities [Volume 53, Issue 11, 2022, Pages 5409-5428]
Khodadadi, Amin Comparison of penetration process of 2-layer elastomeric composite with thermoset composite using energy absorption equations [Volume 53, Issue 6, 2021, Pages 3657-3672]
Khodarahmi, Hossein Experimental investigation and mathematical modeling of the response of circular metallic plates under successive intense dynamic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 4023-4050]
Khoramishad, Hadi A Study on the Ballistic Behavior of Kevlar Fabric Impregnated with Shear Thickening Fluid Containing Graphene Oxide Additive [Volume 53, Issue 12, 2022, Pages 5725-5738]
Khorasanizadeh, Hossein Numerical Simulation of Magnetic Field Effect on Thermal and Thermo-Hydraulic Performance and Entropy Generation of a Silicon Microchannel Heat Sink Under Uniform Heat Flux [Volume 53, Issue 1 (Special Issue), 2021, Pages 517-538]
Khorshidian, Majid Experimental Investigation of Integrated Power System of Dead-End Proton Exchange Membrane Fuel Cell H2/O2 Stack with Large Active Area and Internal Humidifier [Volume 53, Issue 3, 2021, Pages 1667-1676]
Khoshbakhti Saray, Rahim Effect of Start of Injection Timing on Waste Heat Recovery Capacity in a Reactivity Controlled Compression Ignition Engine [Volume 53, Issue 1, 2021, Pages 3-16]
Khoshnejad, Ali Effects of air injection at rotor blade row tip region of an axial compressor on its performance under inlet distortion conditions [Volume 53, Issue 3 (Special Issue), 2021, Pages 1729-1744]
Khoshnevis, Arman Numerical Simulation of Non-Newtonian Blood Flow in A Three-Dimensional Non-Planar Bifurcation with Stenosis [Volume 53, Issue 9, 2021, Pages 4865-4886]
Khosravi Enjedani, Zahra Approximate Torsional Analysis of Arbitrary Trapezoidal Bars by Kantorovich Method [Volume 53, Issue 10, 2022, Pages 5203-5220]
Khosravifard, Seyed Amir Nonlinear Transient Heat Transfer Analysis Using Two Integration Methods with Different Distributions of Integration Points in the Domain in a Meshless Formulation [Volume 53, Issue 1 (Special Issue), 2021, Pages 553-572]
Khosroabadi, Aliasghar Studying of droplet impingement on hydrophilic and hydrophobic curved surfaces by lattice Boltzmann method based on Allen-Cahn equation [Volume 53, Issue 5, 2021, Pages 2869-2886]
Khosrodad, masoud Experimental investigation on MWCNTs-COOH nano fluid on 3D oscillating heat pipe [Volume 53, Issue 5 (Special Issue), 2021, Pages 3401-3416]
Kiani, Maryam Modified Variable Structure Estimation and Control for Constrained Landing on Mars [Volume 53, Issue 10, 2022, Pages 5055-5068]
Koohsorkhi, Javad Vertical growth of titanium dioxide nanorods on nebulizer fluorine doped tin oxide deposited on silicon microarrays [Volume 53, Issue 6 (Special Issue), 2021, Pages 4051-4062]
Kosari, Farshad Reconstruction of Electrical Tomography Images based on Parameter Estimation Method in Inverse Heat Transfer [Volume 53, Issue 1 (Special Issue), 2021, Pages 483-498]
Kouhi Kamali, Ramin Simulation of Two-Phase Flow and Heat Transfer in a Channel and around a Tube by Lattice-Boltzmann Method [Volume 53, Issue 1 (Special Issue), 2021, Pages 499-516]
Kouhi Kamali, Ramin Performance Evaluation of a Fluidized Bed Reactor by Studying the Hydrodynamics and Thermal Properties of Different Solid Particles [Volume 53, Issue 3, 2021, Pages 1573-1590]
Kouhi Kamali, Ramin Two-dimensional simulation of nucleation pool boiling and investigation of phase change mechanism at low heat fluxes [Volume 53, Issue 3 (Special Issue), 2021, Pages 1883-1896]
Kousheshi, navid Investigation of Performance and Emission Characteristic of a Reactivity Controlled Compression Ignition Engine Fueled By a Mixture of Diesel and Syngas Derived From Biomass Gasification [Volume 53, Issue 1, 2021, Pages 17-30]
Kowsari, Farshad Solution of the Isotropic Heat Equation Using the Finite Volume Monte Carlo Method [Volume 53, Issue 1 (Special Issue), 2021, Pages 467-482]
L
Lalegani Dezakia, Amin Numerical Simulation of Elastoplastic Behavior and Damage Evolution at Various Stress Triaxiality [Volume 53, Issue 12, 2022, Pages 5703-5724]
Lashgari, Mohammad Modeling and linearization of longitudinal dynamics for a flapping wing micro aerial vehicle dragonfly-like with active rigid tail [Volume 53, Issue 6, 2021, Pages 3445-3464]
Lexian, Hosein Free and Forced Vibration Analysis of Stiffened Cylindrical Shells under Moving Internal Pressure [Volume 53, Issue 12, 2022, Pages 5867-5886]
Liaghat, gholamhossain Comparison of penetration process of 2-layer elastomeric composite with thermoset composite using energy absorption equations [Volume 53, Issue 6, 2021, Pages 3657-3672]
Liaghat, gholamhossain Numerical analysis of shaped charge jet penetration into discrete concrete targets using LS-DYNA and ANSYS-AUTODYN [Volume 53, Issue 6 (Special Issue), 2021, Pages 3953-3970]
Lopez-Crespo, Pablo Sensitivity analysis of fracture behavior in carbon-epoxy composite at different displacement rates under mode I tensile loading by regression analysis [Volume 53, Issue 4 (Special Issue), 2021, Pages 2671-2686]
M
Maani Miandoab, Ehsan CubeSat antenna vibration control using piezoelectric bender considering system requirements [Volume 53, Issue 4, 2021, Pages 2217-2238]
Madadi, Ali Optimization of The Slotted Gurney-Flap Geometry Applied to NACA 0012 Airfoil for Aerodynamic Performance Improvement [Volume 53, Issue 11, 2022, Pages 5331-5348]
Maddahian, Reza Reconstruction of Electrical Tomography Images based on Parameter Estimation Method in Inverse Heat Transfer [Volume 53, Issue 1 (Special Issue), 2021, Pages 483-498]
Maddahian, Reza Tips on Application of Natural Ventilation in Prevalent Buildings in Iran [Volume 53, Issue 3, 2021, Pages 1621-1636]
Maerefat, Mehdi Tips on Application of Natural Ventilation in Prevalent Buildings in Iran [Volume 53, Issue 3, 2021, Pages 1621-1636]
Maerefat, Mehdi Experimental investigation of personalized ventilation effects on temperature, velocity, and draught discomfort distribution in an office [Volume 53, Issue 7, 2021, Pages 4397-4410]
Mafi, Mostafa Techno-Economic Feasibility of Energy Supply Systems from Renewable Sources of Solar and Biomass in Rural Areas Located In Cold and Dry Climate [Volume 53, Issue 1, 2021, Pages 81-100]
Maghrebi, Mohammad Javad Improving the power coefficient of the Darrieus vertical axis wind turbine with the aid of morphing airfoils [Volume 53, Issue 5 (Special Issue), 2021, Pages 3227-3240]
Maghrebi, Mohammad Javad Improvement of aerodynamic coefficients of the airfoil with free form deformation with the aid of Artificial Neural Networks and Genetic Algorithm [Volume 53, Issue 7, 2021, Pages 4113-4132]
Mahbadi, Hossein The effect of accuracy of the length scale parameter on natural frequencies of porous rectangular microplate [Volume 53, Issue 2 (Special Issue), 2021, Pages 1179-1196]
Mahdavi, Ali Approximate Torsional Analysis of Arbitrary Trapezoidal Bars by Kantorovich Method [Volume 53, Issue 10, 2022, Pages 5203-5220]
Mahdavi, Amir Experimental study of manufacturing and characterization of a flow-focusing microchannel to produce thermoresponsive microparticles for on-demand smart drug delivery [Volume 53, Issue 5 (Special Issue), 2021, Pages 3257-3274]
Mahdavi, Amir Control of droplet size in a two-phase microchannel using PID controller: A novel experimental study [Volume 53, Issue 7, 2021, Pages 4279-4292]
Mahdipour Jalilian, Maziar Numerical investigation and prediction of grain size in different friction stir welding areas of AA6061 aluminum alloy [Volume 53, Issue 6, 2021, Pages 3751-3760]
Mahmoodi Darian, Hossein Developing an alternating direction explicit-implicit domain-decomposition approach to solve heat transfer equation on graphics processing unit [Volume 53, Issue 3 (Special Issue), 2021, Pages 1915-1936]
Mahmoudimehr, Javad Numerical Investigation of the Influence of Burner’s Bluff Body on Air-Fuel Mixing and Reaction [Volume 53, Issue 9, 2021, Pages 4981-4998]
Malek Jafarian, Seyyed Majid Experimental Study of the Effect of Fluid Jet Swirl on Circular Hydraulic Jump [Volume 53, Issue 7, 2021, Pages 4153-4170]
Malek Mohamadi, Shokoufeh Wind simulation in a complex terrain by numerical weather prediction method using large eddy simulation [Volume 53, Issue 7, 2021, Pages 4221-4240]
Malekzadeh Fard, Keramat Analysis of dynamic instability in sandwich thick beams with flexible functional core subjected to a follower force [Volume 53, Issue 2, 2021, Pages 863-880]
Malekzadeh Fard, Keramat Dynamic analysis of cylindrical sandwich shell with orthogonal stiffeners using high-order theory [Volume 53, Issue 4 (Special Issue), 2021, Pages 2473-2492]
Malmir Chegini, Yahya Numerical investigation of the effect of thermophysical properties of nanofluid on fluid flow and heat transfer in a tube in presence of magnetic field [Volume 53, Issue 7, 2021, Pages 4329-4344]
Mani, Mahmoud Experimental investigation of the effect of flapping on the lift and thrust forces of 3D-wing [Volume 53, Issue 3 (Special Issue), 2021, Pages 1697-1708]
Mani, Mahmoud Optimization of The Slotted Gurney-Flap Geometry Applied to NACA 0012 Airfoil for Aerodynamic Performance Improvement [Volume 53, Issue 11, 2022, Pages 5331-5348]
Mansouri, Nematollah Investigate of Hydrodynamic and Mass Transfer in the Spacer-Filled Channel of Reverse Osmosis Module [Volume 53, Issue 1 (Special Issue), 2021, Pages 393-410]
Marashi, SeyedMaziar Experimental verification of indirect bridge mode shape identification using transmissibility of a passing vehicle [Volume 53, Issue 6, 2021, Pages 3529-2548]
Maroofiazar, Rasool Experimental and numerical study of energy harvesting from sloshing of a liquid and its performance on shaper machine [Volume 53, Issue 6 (Special Issue), 2021, Pages 3911-3924]
Maroofiazar, Rasool Passive Control of Vibrations of High-Rise Structure Using Tuned Liquid Damper under Wind and Earthquake Excitations [Volume 53, Issue 11, 2022, Pages 5367-5388]
Masrouri Saadat, Sayed Hossein Experimental Investigation of Integrated Power System of Dead-End Proton Exchange Membrane Fuel Cell H2/O2 Stack with Large Active Area and Internal Humidifier [Volume 53, Issue 3, 2021, Pages 1667-1676]
Mazaheri, Kiumars One-dimensional Combustion Simulation for Different Hydrogen-enriched Natural Gas Blends [Volume 53, Issue 1, 2021, Pages 53-64]
Mazidi, Abbas Modeling and Flutter Analysis of a Three Dimensional Box-Wing using Wagner Unsteady Aerodynamic Model [Volume 53, Issue 12, 2022, Pages 5809-5830]
Mazloum, Jalil Numerical analysis of mechanical micropump using membrane-based check-valves for microfluidic applications [Volume 53, Issue 5 (Special Issue), 2021, Pages 3171-3186]
Mazloum, Jalil Increasing the Sensitivity of SiO2/Al Micro Cantilever Infrared Detector Based on Micro Electromechanical Systems Technology by Optimizing of Dimensions [Volume 53, Issue 8, 2021, Pages 4717-4728]
Mehdipoor, Mahnaz Design and simulation of a biosensor based on a microelectromechanical resonator array [Volume 53, Issue 6 (Special Issue), 2021, Pages 3841-3854]
Mehmannavaz, Hossein Numerical analysis of shaped charge jet penetration into discrete concrete targets using LS-DYNA and ANSYS-AUTODYN [Volume 53, Issue 6 (Special Issue), 2021, Pages 3953-3970]
Mehrdoost, Zahra Multiscale simulation of flow in fractured porous media using unstructured grids [Volume 53, Issue 7, 2021, Pages 4133-4152]
Menhaj, Mohammad Bagher Nonlinear optimal control of an active transfemoral prosthesis using state dependent Riccati equation approach [Volume 53, Issue 4, 2021, Pages 2117-2136]
Mirali, Faraz Experimental investigation of heat transfer and pressure drop in perforated ribs in the solar air heater channel [Volume 53, Issue 3 (Special Issue), 2021, Pages 1981-2000]
Miralinaghi, ئشاسشسشیشف Plastic Deformation of Reinforced Aluminum Plates with Polyurea Coating under Impulsive Loading [Volume 53, Issue 2 (Special Issue), 2021, Pages 1251-1268]
Mirbozorgi, Seyed Ali Numerical analysis of distinction boundary of surface roughness and wall blocks in laminar pressure-driven flow within the rugged microchannels [Volume 53, Issue 5 (Special Issue), 2021, Pages 3241-3256]
Miri-Aliabad, Ghasem Design and Multi-Objective Optimization of A Magnetohydrodynamic Drug Delivery Infusion Micropump [Volume 53, Issue 10, 2022, Pages 5221-5238]
Mirmohammadsadeghi, Sayed Ehsan Mechanistic modeling of cutting forces in milling process by end milling with cutting edges with adjustment angle of 45 degree [Volume 53, Issue 4 (Special Issue), 2021, Pages 2703-2718]
Mirzababaie Mostofi, Tohid Plastic Deformation of Reinforced Aluminum Plates with Polyurea Coating under Impulsive Loading [Volume 53, Issue 2 (Special Issue), 2021, Pages 1251-1268]
Mirzababaie Mostofi, Tohid Effect of intense impulsive loading on performance of multi-layered plates [Volume 53, Issue 4 (Special Issue), 2021, Pages 2639-2670]
Mirzababaie Mostofi, Tohid Investigation of penetration behavior of monolithic and multi-layered metallic targets subjected to a projectile impact [Volume 53, Issue 4, 2021, Pages 2309-2330]
Mirzababaie Mostofi, Tohid Experimental investigation and mathematical modeling of the response of circular metallic plates under successive intense dynamic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 4023-4050]
Mirzaee, Iraj Investigation of the effect of free-wind velocity on the performance of small-scale vertical axis wind turbine [Volume 53, Issue 3 (Special Issue), 2021, Pages 1709-1728]
Mirzaee, Iraj The Effect of Non-Newtonian Behavior on the Transport of Low Density Lipoprotein Particles in the Vortex Region in the Human Carotid Artery [Volume 53, Issue 9, 2021, Pages 4789-4806]
Mirzaee, Majid The Prediction of Femoral Fracture Location Using Extended Finite Element Method [Volume 53, Issue 8, 2021, Pages 4595-4608]
Mirzaluo, Mahdi Experimental Extraction of Young's Modulus of MCF-7 Breast Cancer Cell Using Spherical Contact Models [Volume 53, Issue 12, 2022, Pages 5769-5784]
Mirzanejad, Hossein Study of the Motion Behavior of Soft Fiber Reinforced Actuators Based on Fiber Angle [Volume 53, Issue 8, 2021, Pages 4565-4580]
Moayedi, Hesam Numerical Analysis of Secondary Flow Strength Induced by Electrohydrodynamic Actuator Through a Smooth Channel [Volume 53, Issue 3, 2021, Pages 1401-1416]
Moayedi, Hesam Numerical analysis of the effect of baffle on heat transfer enhancement nanofluid flow over a backward facing step: A correlation for the average Nusselt number [Volume 53, Issue 7, 2021, Pages 4309-4328]
Moayyedi, Mohammad Kazem Development of parametric and time dependent reduced order model for diffusion and convection-diffusion problems based on proper orthogonal decomposition method [Volume 53, Issue 7, 2021, Pages 4241-4260]
Moayyedi, Mohammad Kazem Modeling of turbulent atmospheric boundary layer and dispersion of solid pollutant particles in an urban area using large eddy simulation [Volume 53, Issue 5, 2021, Pages 2839-2856]
Mobadersani, Farrokh Numerical analysis of flow and natural convection heat transfer in a circular enclosure heated from bottom utilizing porous layer [Volume 53, Issue 3 (Special Issue), 2021, Pages 1937-1962]
Mobini Bidgoli, Maryam Modeling of the pilot's depth perception algorithm to avoid collisions with obstacles for commercial aircraft landing [Volume 53, Issue 6, 2021, Pages 3497-3510]
Moghimi, Mahdi Investigate of Hydrodynamic and Mass Transfer in the Spacer-Filled Channel of Reverse Osmosis Module [Volume 53, Issue 1 (Special Issue), 2021, Pages 393-410]
Mohaddes Deylami, Hamed Numerical Analysis of Secondary Flow Strength Induced by Electrohydrodynamic Actuator Through a Smooth Channel [Volume 53, Issue 3, 2021, Pages 1401-1416]
Mohammadi, Abbas A comparison study of deep neural controllers and classic controllers in self-driving car application [Volume 53, Issue 4 (Special Issue), 2021, Pages 2439-2458]
Mohammadi, Abolfazl Experimental Study of Injecting Water Vapor and Oil Compounds by Nebulizer on the Efficiency and Natural Gas Flame Pollution [Volume 53, Issue 1, 2021, Pages 31-40]
Mohammadi, Behzad Energy, Exergy and Economic Analysis of a Semi-solar Greenhouse with Experimental Validation [Volume 53, Issue 3, 2021, Pages 1677-1694]
Mohammadi, Elham Experimental investigation of heat transfer and pressure drop in perforated ribs in the solar air heater channel [Volume 53, Issue 3 (Special Issue), 2021, Pages 1981-2000]
Mohammadi, Hadi Effect of 3D-Printing and Compression Molding on Anisotropy of Acrylonitrile Butadiene Styrene Micro Specimen: A Comparative Study Based on Digital Image Correlation [Volume 53, Issue 12, 2022, Pages 5645-5658]
Mohammadi, Hassan Free vibration analysis of functionally graded carbon nanotubes reinforced composite skew folded plates using the isogeometric approach [Volume 53, Issue 4, 2021, Pages 2239-2260]
Mohammadi, Kamal Experimental Investigation of Water Level Control System of Liquid-Gas Separator in the Fuel Cell [Volume 53, Issue 1 (Special Issue), 2021, Pages 589-604]
Mohammadi, Mehrdad Analytical Study on Effect of Loosening on Nonlinear Vibration Behavior of Bolted Joints [Volume 53, Issue 12, 2022, Pages 5739-5754]
Mohammadi, Mohammad Mahdi Numerical and Experimental Modal Analysis of a 400 W Polymer Electrolyte Membrane Fuel Cell [Volume 53, Issue 1, 2021, Pages 101-116]
Mohammadi, Rafat Numerical simulation of water hammer in various fluids due to a fast valve closure [Volume 53, Issue 7, 2021, Pages 4171-4188]
Mohammadi, Zahra Advanced exergy and thermoeconomic analysis of the supercritical carbon dioxide recompression cycle: A comparative study [Volume 53, Issue 5, 2021, Pages 2967-2982]
Mohammadi, Zeinab Prediction of femoral fracture pattern using finite element analysis of dual-energy X-ray absorptiometry -based model [Volume 53, Issue 2 (Special Issue), 2021, Pages 1223-1236]
Mohammadkari, Behroz Tips on Application of Natural Ventilation in Prevalent Buildings in Iran [Volume 53, Issue 3, 2021, Pages 1621-1636]
Mohammadkhani, Farzad Thermodynamic Analysis of a Novel Power, Cooling, Hydrogen and Oxygen Multi-Generation Combined Cycle Based on the Sabalan Geothermal Wells [Volume 53, Issue 1, 2021, Pages 135-154]
Mohammadpourfard, Mousa Modeling the calcium looping process with an emphasis on the bed hydrodynamics and sorbent characteristics [Volume 53, Issue 5, 2021, Pages 2807-2820]
Mohammad Sadeghiazad, Mohammad Bagher Investigation of Thermo-Hydraulic Parameters of Reactor Containment due to Cold-Leg Break Accident [Volume 53, Issue 3, 2021, Pages 1591-1606]
Mohsenzadeh, Rasool Experimental Studies on The Tribology Behavior of Ultra-High Molecular Weight Polyethylene /Zeolite Nanocomposite [Volume 53, Issue 10, 2022, Pages 5159-5168]
Mokhtari, Davood Numerical/Experimental Investigation of the Presence of a Protuberance in a Convergent – Divergent Nozzle in Supersonic Regime to Control the Thrust Vector [Volume 53, Issue 9, 2021, Pages 4887-4904]
Mokhtari Shirazabad, Mehdi Sensitivity analysis of fracture behavior in carbon-epoxy composite at different displacement rates under mode I tensile loading by regression analysis [Volume 53, Issue 4 (Special Issue), 2021, Pages 2671-2686]
Mollaei, Alireza Study and Optimization of Effective Parameters in The Occurrence of Blush Defect in The Plastic Injection Molding Process by Analysis of Variance [Volume 53, Issue 10, 2022, Pages 5293-5308]
Mollahoseini, Zahra Computational Fluid Dynamics Analysis of Effects of Housing Expansion Angle, Stroke Volume and Path Length of the Fiber Bundles on Function of the Artificial Lung [Volume 53, Issue 11, 2022, Pages 5389-5408]
Mollapour, Yousef Simulation of Pitting Corrosion on Gas Turbine Compressor Blade [Volume 53, Issue 10, 2022, Pages 5123-5140]
Momeni Movahed, Ali Comparison of Support Vector Machine and K-Means Algorithms Performance in Extracting the Real Driving Cycle of Combined Tehran-Amol [Volume 53, Issue 9, 2021, Pages 5017-5036]
Moosavi, Ali Numerical Study of the Dynamics of Non-Newtonian Carreau Droplets under Electrowetting Phenomenon [Volume 53, Issue 1 (Special Issue), 2021, Pages 319-338]
Moosavian, Seyed Ali Akbar Dynamic modeling and control of cleaning robot for agro-photovoltaic [Volume 53, Issue 6, 2021, Pages 3465-3478]
Moosavian, Seyed Ashkan Comparison of Support Vector Machine and K-Means Algorithms Performance in Extracting the Real Driving Cycle of Combined Tehran-Amol [Volume 53, Issue 9, 2021, Pages 5017-5036]
Moqaddas Khorasani, Mahdi Steam generation via solar energy and localizing the light on the pinewood surface [Volume 53, Issue 3 (Special Issue), 2021, Pages 2001-2012]
Moradi, Mahmoud Statistical analysis and optimization of tensile strength of Al7075 butt joint produced by friction stir welding and submerged friction stir welding via response surface methodology and desirability approach [Volume 53, Issue 4 (Special Issue), 2021, Pages 2719-2734]
Moradi Kashkooli, Farshad Image-based numerical model for drug delivery to solid tumors [Volume 53, Issue 5 (Special Issue), 2021, Pages 3187-3200]
Mosavi, Seyed Ali Experimental investigation of the infeed method and machining parameters on the tool wear during thread milling [Volume 53, Issue 2 (Special Issue), 2021, Pages 1345-1356]
Mosharaf Dehkordi, Mahdi Numerical Simulation of Variable Conductance Heat Pipe with Cold Reservoir by Single Phase Flow Approach [Volume 53, Issue 9, 2021, Pages 4905-4924]
Mottaghi, Sina Control of droplet size in a two-phase microchannel using PID controller: A novel experimental study [Volume 53, Issue 7, 2021, Pages 4279-4292]
Mousavi, Fateme Comparison of axial and radial soil temperature distribution in U-tube and coaxial borehole heat exchangers [Volume 53, Issue 7, 2021, Pages 4361-4378]
Mousavian, seyed amir Tips on Application of Natural Ventilation in Prevalent Buildings in Iran [Volume 53, Issue 3, 2021, Pages 1621-1636]
Movahedin, Mansoureh Numerical Study on the Complete Separation of Blood Cells using the Integrated Dielectrophoretic-Photophoretic Method in a New Microchannel [Volume 53, Issue 1 (Special Issue), 2021, Pages 655-670]
Mozafarie, Seyed Shahab Numerical Simulation of Heat Transfer Turbulent Flow for Non-Newtonian Nanofluid in a Double Pipe Helical Heat Exchanger [Volume 53, Issue 1, 2021, Pages 221-240]
N
Nabakhteh, Mohammad Amin Numerical analysis of shaped charge jet penetration into discrete concrete targets using LS-DYNA and ANSYS-AUTODYN [Volume 53, Issue 6 (Special Issue), 2021, Pages 3953-3970]
Naeimi, Hooman Solution of the Isotropic Heat Equation Using the Finite Volume Monte Carlo Method [Volume 53, Issue 1 (Special Issue), 2021, Pages 467-482]
Naghash, Abolghasem Modeling and linearization of longitudinal dynamics for a flapping wing micro aerial vehicle dragonfly-like with active rigid tail [Volume 53, Issue 6, 2021, Pages 3445-3464]
Naghash, Abolghasem A Fast Warehouse Inventory Micro Aerial Vehicle System Equipped with Visual Guidance and Navigation Algorithm [Volume 53, Issue 12, 2022, Pages 5785-5808]
Naghizadeh, Amirhosein A Study on the Ballistic Behavior of Kevlar Fabric Impregnated with Shear Thickening Fluid Containing Graphene Oxide Additive [Volume 53, Issue 12, 2022, Pages 5725-5738]
Najafian, Mojtaba Experimental Study of Injecting Water Vapor and Oil Compounds by Nebulizer on the Efficiency and Natural Gas Flame Pollution [Volume 53, Issue 1, 2021, Pages 31-40]
Nakhaei Zeinali, Elham Investigation on flow air concentration effect on distance of the chute spillway aerators [Volume 53, Issue 5 (Special Issue), 2021, Pages 3135-3150]
Namadchian, Hosein Numerical simulation of nanofluid flow in an annulus with porous baffles based on combination of Darcy-Brinkman-Forchheimer model and two-phase mixture model [Volume 53, Issue 3 (Special Issue), 2021, Pages 1897-1914]
Namdari, Sina Control of Vehicle’s Mixed Longitudinal and Lateral Stability with Engine Dynamics Using Super Twisting Control Algorithm [Volume 53, Issue 2, 2021, Pages 959-978]
Nariman-zadeh, Nader Designing Optimum Multi-Domain System by Integrating Bond Graph and Genetic Programming [Volume 53, Issue 2, 2021, Pages 1015-1038]
Naseri, Reza Theoretical Analysis of Equal Channel Angular Pressing Process by Upper Bound Method and Its Experimental Investigation in Condition of Circular Cross-Section Channel [Volume 53, Issue 8, 2021, Pages 4729-4744]
Nasiri, Mostafa Time-delay compensation for networked hardware-in-the-loop simulation of a flight control system using polynomial prediction [Volume 53, Issue 2 (Special Issue), 2021, Pages 1111-1124]
Nasiri, Mostafa Stability Analysis of Predictive Control in Networked Control System Using Switching Control [Volume 53, Issue 10, 2022, Pages 5039-5054]
Navabi, M. Unstable Aircraft Flight Control Based on Linear Matrix Inequality with Consideration of Control and Saturation Constraints [Volume 53, Issue 2, 2021, Pages 979-992]
Navidbakhsh, Mahdi Design, Fabrication and Experimental Study of Spiral Microchannel Particle Separator on Centrifugal Microfluidic Platforms [Volume 53, Issue 3, 2021, Pages 1359-1372]
Nayebi, Elahe Fractional calculus approach for bending of viscoelastic plate using two-variable refined plate theory [Volume 53, Issue 4, 2021, Pages 2287-2308]
Nayebi, Peyman Investigation on Mechanical Properties of Polyoxymethylene Reinforced by Carbon Nanotube Using Molecular Dynamics [Volume 53, Issue 8, 2021, Pages 4691-4700]
Nazari, Ahmad Experimental study of CuO/Water nanofluid pool boiling on the copper flat surface and measurement of the critical heat flux [Volume 53, Issue 5, 2021, Pages 3099-3114]
Nazari, Mohsen Experimental Study of Surfactant Type Effects on the Foam Stability and Mobility With the Approach of Enhancing Oil Recovery [Volume 53, Issue 1 (Special Issue), 2021, Pages 339-356]
Nazari, Mohsen Measurement of subcooled flow boiling heat transfer coefficient in vertical annulus tube [Volume 53, Issue 7, 2021, Pages 4345-4360]
Nazari, Mohsen Experimental study of manufacturing and characterization of a flow-focusing microchannel to produce thermoresponsive microparticles for on-demand smart drug delivery [Volume 53, Issue 5 (Special Issue), 2021, Pages 3257-3274]
Nazari, Mohsen Control of droplet size in a two-phase microchannel using PID controller: A novel experimental study [Volume 53, Issue 7, 2021, Pages 4279-4292]
Nazari, Mohsen Convection Heat transfer Fe3O4/Water in a Square microchannel Under Uniform Heat Flux and Magnetic Field [Volume 53, Issue 9, 2021, Pages 4925-4942]
Nazari, Mostafa Control of droplet size in a two-phase microchannel using PID controller: A novel experimental study [Volume 53, Issue 7, 2021, Pages 4279-4292]
Nazari-Onlaghi, Sina Effect of 3D-Printing and Compression Molding on Anisotropy of Acrylonitrile Butadiene Styrene Micro Specimen: A Comparative Study Based on Digital Image Correlation [Volume 53, Issue 12, 2022, Pages 5645-5658]
Nazemian, Mehrdad Effect of Start of Injection Timing on Waste Heat Recovery Capacity in a Reactivity Controlled Compression Ignition Engine [Volume 53, Issue 1, 2021, Pages 3-16]
Nazmi, Parsa Numerical simulation of Holmboe waves in intrusive gravity current using LES method [Volume 53, Issue 7, 2021, Pages 4261-4278]
Nazmi, Parsa Studying Wind Effect on the Hydrodynamic Behavior of Lock-Exchange Density Current [Volume 53, Issue 9, 2021, Pages 4807-4826]
Negahban.B, Ali Experimental Investigation of the Performance of Trailing Edge Noise-Reducing Finlets [Volume 53, Issue 9, 2021, Pages 4827-4846]
Neshat, Elahe Effect of Start of Injection Timing on Waste Heat Recovery Capacity in a Reactivity Controlled Compression Ignition Engine [Volume 53, Issue 1, 2021, Pages 3-16]
Neshat, Elahe Investigation on Effects of Water Addition on Performance and Emissions of an n-heptane Fueled Homogeneous Charge Compression Ignition Engine [Volume 53, Issue 3, 2021, Pages 1637-1652]
Nezamivand Chegini, Saeed Denoising vibration signals of rotating machines using probability density function, similarity measure and improved thresholding function [Volume 53, Issue 4 (Special Issue), 2021, Pages 2493-2512]
Niazmand, Hamid Steam generation via solar energy and localizing the light on the pinewood surface [Volume 53, Issue 3 (Special Issue), 2021, Pages 2001-2012]
Nikaeen, Golbarg Study of the Motion Behavior of Soft Fiber Reinforced Actuators Based on Fiber Angle [Volume 53, Issue 8, 2021, Pages 4565-4580]
Nikbin, Kamran Micromechanical Damage Model for Plasticity of Metals to Predict Failure under Shear Loads [Volume 53, Issue 12, 2022, Pages 5679-5702]
Nikoobin, Amin Torque minimization of 2-DOF parallel robot using counterweights and trajectory planning [Volume 53, Issue 4 (Special Issue), 2021, Pages 2409-2422]
Nikoobin, Amin A new optimal structural boundary modification algorithm in the multi-objective topology optimization of microgripper [Volume 53, Issue 4, 2021, Pages 2261-2270]
Nilforooshan Dardashti, Behnam Convection Heat transfer Fe3O4/Water in a Square microchannel Under Uniform Heat Flux and Magnetic Field [Volume 53, Issue 9, 2021, Pages 4925-4942]
Noghreabadi, Amin Reza Investigation of Heat Transfer of Non-Newtonian Pseudo-Plastic Fluids in Porous Heat Exchangers [Volume 53, Issue 1, 2021, Pages 241-258]
Noorian, Mohammad Ali Investigation of Nonlinear Vibrations of A Cantilever Beam with A Transverse Fatigue Crack [Volume 53, Issue 10, 2022, Pages 5069-5084]
Norouzi, Mahmood Experimental Study of Surfactant Type Effects on the Foam Stability and Mobility With the Approach of Enhancing Oil Recovery [Volume 53, Issue 1 (Special Issue), 2021, Pages 339-356]
Norouzi, Mahmood Manufacturing and Testing of an Optimized Magneto-Rheological Fluid and Modelling of a Twin Tube Magneto-Rheological Damper Using a Modified Non-Newtonian Model Using Analytical Quasi-Static, Analytical Unsteady, Numerical and Experimental Methods [Volume 53, Issue 3, 2021, Pages 1373-1400]
Nourazar, Seyed Salman Simulation, manufacturing and test of a transparent proton-exchange membrane fuel cell [Volume 53, Issue 3 (Special Issue), 2021, Pages 2031-2052]
Nourizade, Majede Simulation of a Photocatalytic Reactor Using Finite Volume and Discrete Ordinate Method: A Parametric Study [Volume 53, Issue 1 (Special Issue), 2021, Pages 573-588]
Nourollahi Golouje, Yavar Numerical analysis of chaotic dynamics in vehicle along with design of chaos controller using fuzzy fast terminal sliding mode control [Volume 53, Issue 4 (Special Issue), 2021, Pages 2539-2556]
N. Toossi, Shahin Global sensitivity analysis of nanomachining parameters by using dynamic scanning thermal microscope [Volume 53, Issue 4, 2021, Pages 2367-2384]
O
Ojaghnezhad, Farzaneh Spherical Lame-Type Problem in Second Strain Gradient Theory [Volume 53, Issue 2, 2021, Pages 709-728]
Orumiyeh-e, Aida Energy and Exergy Analysis of Organic Rankine Cycle Fed by Electric Arc Furnace Waste Heat [Volume 53, Issue 9, 2021, Pages 4999-5016]
P
Pahlevaninejad, Nadia The effect of hole on the rectangular vortex generator on thermal-hydrodynamic performance of the minichannel [Volume 53, Issue 7, 2021, Pages 4293-4308]
Pakravan, Hossein Ali Numerical study of the effect of left coronary artery stenosis on vascular tissue oxygenation [Volume 53, Issue 3 (Special Issue), 2021, Pages 1767-1782]
Panahizadeh, Valiollah Optimization of Additive Manufactured Part Made by Ti6Al4V Alloy to Achieve Best Relative Density and Surface Roughness [Volume 53, Issue 10, 2022, Pages 5169-5184]
Parhizkar Yaghoobi, Mohammad 2-Dimensional Electroelastic Analysis of Piezoelectric Cylinders Using First-Order Shear Deformation and First-Order Electric Potential Theories [Volume 53, Issue 2, 2021, Pages 815-832]
Pasdarshahri, Hadi Experimental Investigation of Combustion Species Radiation to Evaluate Equivalence Ratio in a Surface Flame Burner [Volume 53, Issue 1, 2021, Pages 41-52]
Pasdarshahri, Hadi Accurate and faster than real-time simulation of indoor airflow by using fast fluid dynamics [Volume 53, Issue 3 (Special Issue), 2021, Pages 1839-1860]
PasdarShahri, Hadi Dynamic Simulation of Desiccant Cooling System with Simultaneously Using Solar and Ground Renewable Energies in Hot-Humid Regions [Volume 53, Issue 3, 2021, Pages 1549-1572]
PasdarShahri, Hadi Comparison study of compartment fire simulation with steady laminar flamelet and eddy dissipation model [Volume 53, Issue 5, 2021, Pages 2953-2966]
PasdarShahri, Hadi Numerical investigation of compartment fire under maximum and minimum of natural ventilation using flamelet generated manifold combustion model [Volume 53, Issue 5 (Special Issue), 2021, Pages 3335-3350]
Pashaei, Mohammad Hadi Experimental verification of indirect bridge mode shape identification using transmissibility of a passing vehicle [Volume 53, Issue 6, 2021, Pages 3529-2548]
Pashaei, Naser Experimental and numerical study of energy harvesting from sloshing of a liquid and its performance on shaper machine [Volume 53, Issue 6 (Special Issue), 2021, Pages 3911-3924]
Payganeh, Gholamhasan Analysis of dynamic instability in sandwich thick beams with flexible functional core subjected to a follower force [Volume 53, Issue 2, 2021, Pages 863-880]
Peighambarsoust, Seyed Jamaledin Removal of Lead Heavy Metal from Wastewater by Crystallization Process and Investigation of the Effective Parameters [Volume 53, Issue 11, 2022, Pages 5349-5366]
Peikani, Pantheia Experimental and Numerical Investigation of Film Cooling Effectiveness on Squealer Tip of a Turbine Blade [Volume 53, Issue 3, 2021, Pages 1521-1536]
Pirdayr, Abouzar Analytical Study on Effect of Loosening on Nonlinear Vibration Behavior of Bolted Joints [Volume 53, Issue 12, 2022, Pages 5739-5754]
Pirhadi, Ebrahim Experimental and theoretical investigation of the critical load of U-notched laminated composite specimens under in-plane shear loading [Volume 53, Issue 6, 2021, Pages 3673-3688]
Pormahmod Hesar, Nader The Effect of Non-Newtonian Behavior on the Transport of Low Density Lipoprotein Particles in the Vortex Region in the Human Carotid Artery [Volume 53, Issue 9, 2021, Pages 4789-4806]
Pourgholi, Mehdi Modeling, design and investigation of seat suspension based on negative stiffness structure to improve the vibration environment for helicopter pilots [Volume 53, Issue 4 (Special Issue), 2021, Pages 2513-2538]
Pourkamali Anaraki, Ali Investigation of the micromechanical behavior of ferritic-martensitic steel under complex loading [Volume 53, Issue 6, 2021, Pages 3689-3702]
Pourmoayed, Alireza Dynamic analysis of cylindrical sandwich shell with orthogonal stiffeners using high-order theory [Volume 53, Issue 4 (Special Issue), 2021, Pages 2473-2492]
Poursaeidi, Esmaeil Investigation of Crack Growth in Deposited and Perfect Titanium/Titanium Nitride Structure by Molecular Dynamic Simulation [Volume 53, Issue 2, 2021, Pages 833-850]
Poursaeidi, Esmaeil Experimental Study of Effects of Hydrogen Embrittlement and Residual Stress on Mechanical Properties of GTD450 [Volume 53, Issue 12, 2022, Pages 5659-5678]
PourSaeidi, Esmaeil Simulation of Pitting Corrosion on Gas Turbine Compressor Blade [Volume 53, Issue 10, 2022, Pages 5123-5140]
Q
Qaraati, Tabanmehr Comparison of Support Vector Machine and K-Means Algorithms Performance in Extracting the Real Driving Cycle of Combined Tehran-Amol [Volume 53, Issue 9, 2021, Pages 5017-5036]
R
Raad, Mohammad Numerical simulation of droplet formation in a T-shape microchannel using two-phase level-set method [Volume 53, Issue 3 (Special Issue), 2021, Pages 1815-1838]
Rabiee, Amir Hossein Real Time Solution for Inverse Heat Conduction Problem in One-Dimensional Plate Utilizing Fuzzy- Proportional–Integral–Derivative Controller [Volume 53, Issue 1, 2021, Pages 303-316]
Rabiee, Amir Hossein Process modeling of force behavior in the automatic bovine cortical bone milling process using adaptive neuro-fuzzy inference system [Volume 53, Issue 2 (Special Issue), 2021, Pages 1287-1306]
Raesi, Mohammad Experimental evaluation of the effect of supply air direction on air current and temperature in a room with underfloor air distribution system [Volume 53, Issue 5, 2021, Pages 3057-3076]
Rafee, Roholah Investigating the Effects of Loung Chair Fire in a Cinema Hall Using Displacement, Impingement Jet and Stratum Ventilation Systems [Volume 53, Issue 11, 2022, Pages 5573-5594]
Rahgoshay, Seyyed Majid Experimental Investigation of Water Level Control System of Liquid-Gas Separator in the Fuel Cell [Volume 53, Issue 1 (Special Issue), 2021, Pages 589-604]
Rahgoshay, Seyyed Majid Experimental Investigation of Integrated Power System of Dead-End Proton Exchange Membrane Fuel Cell H2/O2 Stack with Large Active Area and Internal Humidifier [Volume 53, Issue 3, 2021, Pages 1667-1676]
Rahimi, Fatemeh Control of the Amount of Oncolytic Virus Injection by Considering Time Delay [Volume 53, Issue 2 (Special Issue), 2021, Pages 1125-1136]
Rahimi, Gholam Hosein Nonlinear analysis of hyperelastic plates using first-order shear deformation plate theory and a meshless method [Volume 53, Issue 4, 2021, Pages 2331-2346]
Rahimi, Masoume The effect of hole on the rectangular vortex generator on thermal-hydrodynamic performance of the minichannel [Volume 53, Issue 7, 2021, Pages 4293-4308]
Rahimian, Mohammad Hasan Simulation of Two-Phase Flow and Heat Transfer in a Channel and around a Tube by Lattice-Boltzmann Method [Volume 53, Issue 1 (Special Issue), 2021, Pages 499-516]
Rahimi Esboee, Mazaher Experimental Investigation of Water Level Control System of Liquid-Gas Separator in the Fuel Cell [Volume 53, Issue 1 (Special Issue), 2021, Pages 589-604]
Rahimi Esboee, Mazaher Experimental Investigation of Integrated Power System of Dead-End Proton Exchange Membrane Fuel Cell H2/O2 Stack with Large Active Area and Internal Humidifier [Volume 53, Issue 3, 2021, Pages 1667-1676]
Rahmani, Hossein Investigation of Quality Factor for Linear Vibrations of Rectangular Micro-plates with Thermoelastic Damping [Volume 53, Issue 2, 2021, Pages 851-862]
Rahmani, Mehdi Double Hyperbolic Sliding Mode Control Based on Unscented Kalman Filter for Three-legged Mobile manipulator [Volume 53, Issue 4, 2021, Pages 2105-2116]
Rahmani, Mehdi Fault detection and isolation based on robust Kalman filter for discrete-time systems with stochastic and norm-bounded uncertainties [Volume 53, Issue 6 (Special Issue), 2021, Pages 3825-3840]
Rahmani, Mohammad Simulation of a Photocatalytic Reactor Using Finite Volume and Discrete Ordinate Method: A Parametric Study [Volume 53, Issue 1 (Special Issue), 2021, Pages 573-588]
Rahmani, Omid Free vibration of axially functionally graded nanobeam with an attached mass based on nonlocal strain gradient theory via new ADM numerical method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1159-1178]
Rahmani Firoozjaiee, Ali Numerical Investigation of Scour Around a Cylindrical Pier in Laboratory Scale Using Euler-Lagrange Approach [Volume 53, Issue 1 (Special Issue), 2021, Pages 411-426]
Rahmani Hanzaki, Ali Out-of-Plane Vibration Mitigation of Wind Turbine Blade Using Highly Efficient Nonlinear Energy Sink [Volume 53, Issue 12, 2022, Pages 5851-5866]
Rahmati, Abbas Kinematic Optimization of the Stirling engine for Maximum Output Work and Constraint of Occupied Space [Volume 53, Issue 7, 2021, Pages 4455-4480]
Raisi, Afrasiab Numerical simulation of mixed convection of Bingham fluid between two coaxial cylinders [Volume 53, Issue 5 (Special Issue), 2021, Pages 3417-3428]
Raisi, Afrasiab Numerical Study of Natural Convection Heat Transfer inside a Triangular Cavity with Flexible Sidewalls Containing a Cylindrical Heat Source [Volume 53, Issue 11, 2022, Pages 5461-5484]
Rajabi, Majid Analytical Study on Effect of Loosening on Nonlinear Vibration Behavior of Bolted Joints [Volume 53, Issue 12, 2022, Pages 5739-5754]
Rajabi Zargarabadi, Mehran Study of the Flow and Heat Transfer of Pulsed Sinusoidal Impinging Jet at Distances Close To the Concave Surface [Volume 53, Issue 9, 2021, Pages 4943-4960]
Rakhsha, Saeed Study of the Flow and Heat Transfer of Pulsed Sinusoidal Impinging Jet at Distances Close To the Concave Surface [Volume 53, Issue 9, 2021, Pages 4943-4960]
Ramezani, Ali Numerical analysis of shaped charge jet penetration into discrete concrete targets using LS-DYNA and ANSYS-AUTODYN [Volume 53, Issue 6 (Special Issue), 2021, Pages 3953-3970]
Ramezani, Mostafa Investigating the Effects of Loung Chair Fire in a Cinema Hall Using Displacement, Impingement Jet and Stratum Ventilation Systems [Volume 53, Issue 11, 2022, Pages 5573-5594]
Ramezani Voloojerdi, Mojtaba Experimental investigation of the effect of flapping on the lift and thrust forces of 3D-wing [Volume 53, Issue 3 (Special Issue), 2021, Pages 1697-1708]
Ramezannejad Azarboni, Habib Instability and frequency sensitivity analysis of single-walled carbon nanotubes conveying fluid under thermomagnetic field considering the surface effect [Volume 53, Issue 6 (Special Issue), 2021, Pages 3875-3890]
Ramezanpour, Ahad Experimental Investigation of Thermal Performance of Pulsating Heat Pipe at Angles Close To the Horizon [Volume 53, Issue 11, 2022, Pages 5445-5460]
Ranjbar, Ali Akbar The effect of hole on the rectangular vortex generator on thermal-hydrodynamic performance of the minichannel [Volume 53, Issue 7, 2021, Pages 4293-4308]
Ranjbar, Seyed Faramarz Energy, Exergy and Economic Analysis of a Semi-solar Greenhouse with Experimental Validation [Volume 53, Issue 3, 2021, Pages 1677-1694]
Ranjkesh Adarmanabadi, Sedigheh An experimental investigation of the effect of the type of nanostructured reinforcements on the mechanical and tribological properties of epoxy based nanocomposites [Volume 53, Issue 6 (Special Issue), 2021, Pages 4009-4022]
Rashed Saghavaz, Fahimeh Analysis of dynamic instability in sandwich thick beams with flexible functional core subjected to a follower force [Volume 53, Issue 2, 2021, Pages 863-880]
Rastegari, Rambod Planar Object Manipulation with Multi Fingers Robot Located on a Moving Hand Under Rolling Grasp Constrains [Volume 53, Issue 2, 2021, Pages 943-958]
Rayegan, Saeed Dynamic Simulation of Desiccant Cooling System with Simultaneously Using Solar and Ground Renewable Energies in Hot-Humid Regions [Volume 53, Issue 3, 2021, Pages 1549-1572]
Razavi, Seyed Esmail Investigating the Fluid-Solid Interaction in Incompressible Flow and The Effect of Oscillation Amplitude on Heat Transfer [Volume 53, Issue 9, 2021, Pages 4747-4772]
Razavi, SMH Experimental Study of Surfactant Type Effects on the Foam Stability and Mobility With the Approach of Enhancing Oil Recovery [Volume 53, Issue 1 (Special Issue), 2021, Pages 339-356]
Razeghi, Seyed Mohammad Jamal Comparison study of compartment fire simulation with steady laminar flamelet and eddy dissipation model [Volume 53, Issue 5, 2021, Pages 2953-2966]
Razfar, Mohammad Reza Experimental study of machining residual stresses in plasma-assisted turning process [Volume 53, Issue 4, 2021, Pages 2385-2406]
Razfar, Mohammad Reza Experimental Study of the Effect of Initial Surface Roughness on Ball Burnishing Forces and Endurance Limit of AISI 4130 Hardened Steel [Volume 53, Issue 12, 2022, Pages 5627-5644]
Rezaei, Hadi Influence of Pseudo-Boiling Phenomenon and the Mass Flux Ratio on the Dynamics of Transcritical Shear Flame [Volume 53, Issue 9, 2021, Pages 4961-4980]
Rezaie, Mehran A comparison study of deep neural controllers and classic controllers in self-driving car application [Volume 53, Issue 4 (Special Issue), 2021, Pages 2439-2458]
Rezapour Khaneghah, Saeed Control of Vehicle’s Mixed Longitudinal and Lateral Stability with Engine Dynamics Using Super Twisting Control Algorithm [Volume 53, Issue 2, 2021, Pages 959-978]
Rezasefat, Mohammad Effect of intense impulsive loading on performance of multi-layered plates [Volume 53, Issue 4 (Special Issue), 2021, Pages 2639-2670]
Rezazadeh, Sajadollah Numerical simulation of droplet formation in a T-shape microchannel using two-phase level-set method [Volume 53, Issue 3 (Special Issue), 2021, Pages 1815-1838]
Riyahi Vezvari, Mojtaba Torque minimization of 2-DOF parallel robot using counterweights and trajectory planning [Volume 53, Issue 4 (Special Issue), 2021, Pages 2409-2422]
Rostami, Mohsen Energy Analysis and Exergy of the System of Simultaneous Production of Power and Hydrogen with the Excitatory Gasification of Municipal Solid Waste [Volume 53, Issue 11, 2022, Pages 5529-5550]
Rostami Dehjalali, Sadegh Numerical simulation of Holmboe waves in intrusive gravity current using LES method [Volume 53, Issue 7, 2021, Pages 4261-4278]
Rostami Dehjalali, Sadegh Studying Wind Effect on the Hydrodynamic Behavior of Lock-Exchange Density Current [Volume 53, Issue 9, 2021, Pages 4807-4826]
Rostamzadeh, Hadi Design and evaluation of a novel bi-evaporator combined power and refrigeration cycle working with various zeotropic mixtures [Volume 53, Issue 5, 2021, Pages 3003-3022]
Rouhani, Fatemeh Finite element modeling of shape memory alloy stent insertion in the vessel with consideration of vessel damage [Volume 53, Issue 2 (Special Issue), 2021, Pages 1211-1222]
Rouhbakhsh, Mohsen Numerical analysis of shaped charge jet penetration into discrete concrete targets using LS-DYNA and ANSYS-AUTODYN [Volume 53, Issue 6 (Special Issue), 2021, Pages 3953-3970]
Rouhollahi, Amirhossein A numerical investigation on the effect of blade tip shapes on power generation of a horizontal axis wind turbine [Volume 53, Issue 5, 2021, Pages 2791-2806]
Rouzegar, Seyed Jafar Fractional calculus approach for bending of viscoelastic plate using two-variable refined plate theory [Volume 53, Issue 4, 2021, Pages 2287-2308]
S
Sabaghzadeghan, Farshad Development of parametric and time dependent reduced order model for diffusion and convection-diffusion problems based on proper orthogonal decomposition method [Volume 53, Issue 7, 2021, Pages 4241-4260]
Saberi, Ali Analysis of Density Wave Oscillations in a Boiling Channel by a New Analytical Model [Volume 53, Issue 3, 2021, Pages 1505-1520]
Saberi, Ali Quantifying of viscous fingering instability in porous media [Volume 53, Issue 5, 2021, Pages 2887-2902]
Saberi Mehr, Ali Investigation of Performance and Emission Characteristic of a Reactivity Controlled Compression Ignition Engine Fueled By a Mixture of Diesel and Syngas Derived From Biomass Gasification [Volume 53, Issue 1, 2021, Pages 17-30]
Sabermanesh, Hamid Reza Effect of adding carbon nanotubes into the matrix material on the buckling behavior of glass/epoxy composite plates: An experimental study [Volume 53, Issue 4 (Special Issue), 2021, Pages 2613-2628]
Sabzeh Parvar, Mehdi Control of quadrotor by using state-dependent Riccati equation method and analyzing its dynamic performance under wind field [Volume 53, Issue 4 (Special Issue), 2021, Pages 2423-2438]
Sabzeh Parvar, Mehdi Modeling of the pilot's depth perception algorithm to avoid collisions with obstacles for commercial aircraft landing [Volume 53, Issue 6, 2021, Pages 3497-3510]
Sabzpooshani, Majid Experimental Investigation on the Thermal Resistance of Straight Heat Pipes with Double-Ended Cooling and Middle-Heating at Different Tilt Angles [Volume 53, Issue 1, 2021, Pages 279-302]
Sabzpooshani, Majid Investigation on the effect of addition of nano-titanium oxide particles to phase change material in a hybrid system for battery cooling under constant heat flux [Volume 53, Issue 7, 2021, Pages 4379-4396]
Sadatsakak, Seyed Abbas Simulation and Optimization of Rankine Power Generation Cycle Purposing the Efficiency of Liquefied Natural Gas Cold Exergy [Volume 53, Issue 1, 2021, Pages 117-134]
Sadeghi, Alireza Simulation and Optimization of Rankine Power Generation Cycle Purposing the Efficiency of Liquefied Natural Gas Cold Exergy [Volume 53, Issue 1, 2021, Pages 117-134]
Sadeghi, Alireza Effect of 3D-Printing and Compression Molding on Anisotropy of Acrylonitrile Butadiene Styrene Micro Specimen: A Comparative Study Based on Digital Image Correlation [Volume 53, Issue 12, 2022, Pages 5645-5658]
Sadeghi, Mohammad Hosein Laser Cladding of TiC/316LSS and Analysis of Input Parameters using Response Surface Method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1269-1286]
Sadeghi, Morteza Identification and damage detection of beam-like structure using vibration signals based on simulated model, real healthy state and deep convolutional neural network [Volume 53, Issue 4, 2021, Pages 2193-2216]
Sadeghi, Morteza Damage detection of offshore jacket structure using dynamic responses based on simulated model, intact state of real model and deep auto-encoder neural network [Volume 53, Issue 6 (Special Issue), 2021, Pages 3783-3808]
Sadeghian, Hadi Experimental and Theoretical Assessment of Mode II Fracture Toughness for Cracked Ductile Specimens with High Strain-Hardening [Volume 53, Issue 10, 2022, Pages 5141-5158]
Sadeghzadeh, Arash Assessing short-term storage effects on hydrostatic wind turbine in presence of turbulent wind [Volume 53, Issue 6, 2021, Pages 3431-3444]
Sadighi, Mojtaba Micro-Mechanical Damage Analysis of Al-TiC Particulate Reinforced Composites by Peridynamic Theory [Volume 53, Issue 8, 2021, Pages 4701-4716]
Sadighi, Mojtaba Modeling of vibro-acoustic modulation induced by non-linear contact in the Euler-Bernoulli beam using the Fourier spectral element [Volume 53, Issue 6 (Special Issue), 2021, Pages 3809-3824]
Sadooghi, Ala Numerical investigation of ethanol and acetone spray injection into gaseous environment [Volume 53, Issue 5 (Special Issue), 2021, Pages 3213-3226]
Sadri Qahfarrokhi, Arash Investigation to set the type of pre-chamber fuel system in heavy gas engine HIMSEN 35/40 [Volume 53, Issue 5, 2021, Pages 2935-2952]
Saedodin, Seyfolah Study of the Flow and Heat Transfer of Pulsed Sinusoidal Impinging Jet at Distances Close To the Concave Surface [Volume 53, Issue 9, 2021, Pages 4943-4960]
Saeedi, Ali Numerical Investigation of the Performance of Hydrogen Production Process by Production Gas Recirculation [Volume 53, Issue 1 (Special Issue), 2021, Pages 623-638]
Saeedi, Mohammad Numerical Investigation of Hybrid Wick Structure Effect on Thermal Performance of a Thin Flat Heat Pipe [Volume 53, Issue 11, 2022, Pages 5485-5504]
Saeedi, Mostafa Sensitivity analysis of fracture behavior in carbon-epoxy composite at different displacement rates under mode I tensile loading by regression analysis [Volume 53, Issue 4 (Special Issue), 2021, Pages 2671-2686]
Safar, Mahmoud Diagnostical and observational analysis of clear air turbulence over the middle east and Iran [Volume 53, Issue 7, 2021, Pages 4203-4220]
Safari, Mahdi Process modeling of force behavior in the automatic bovine cortical bone milling process using adaptive neuro-fuzzy inference system [Volume 53, Issue 2 (Special Issue), 2021, Pages 1287-1306]
Safari, Omid Finite Element Modeling of a Novel Magnetic Shape Memory Alloy Based Energy Harvester Using a Corrugated Beam and Investigating the Effective Parameters [Volume 53, Issue 2, 2021, Pages 799-814]
Saidi, Ali Reza Nonlinear Vibrations of Graphene Reinforced Pipes Conveying Fluid [Volume 53, Issue 8, 2021, Pages 4483-4500]
Sajadi, Hasan Analytical Solution of Heat Transfer in a Cone Made of Functionally Graded Material [Volume 53, Issue 1 (Special Issue), 2021, Pages 539-552]
Sajjadi, Hasan Investigation of the Effect of Ventilation System Inlet Location on Particle Motion in a Room Using Multi Relaxation Time-Lattice Boltzmann Method [Volume 53, Issue 3, 2021, Pages 1457-1468]
Salehi, Gholamreza Investigation of hydrogen production process by partial oxidation of natural gas in a large non-catalytic reformer and comparison with methane steam reforming process in a small catalytic reformer [Volume 53, Issue 5 (Special Issue), 2021, Pages 3275-3292]
Salehi Kolahi, Mohammad Reza Investigation of Quality Factor for Linear Vibrations of Rectangular Micro-plates with Thermoelastic Damping [Volume 53, Issue 2, 2021, Pages 851-862]
Salimi Nezhad, Iman Evaluating the effects of material extrusion 3D printing process parameters on shape-shifting of Poly-lactic acid 4D-printed structures [Volume 53, Issue 6 (Special Issue), 2021, Pages 4095-4110]
Sam Daliri, Omid Condition monitoring of defective single lap adhesive joint using carbon nanotubes [Volume 53, Issue 2 (Special Issue), 2021, Pages 1321-1330]
Sanaei, Hassan Numerical study and investigation of the effect of magnetic field on fluid hydrodynamic behavior [Volume 53, Issue 5, 2021, Pages 2857-2868]
Sanaye, Sepehr Comparison of axial and radial soil temperature distribution in U-tube and coaxial borehole heat exchangers [Volume 53, Issue 7, 2021, Pages 4361-4378]
Sangtarash, Mohammad Reza The Feasibility Study of a Night Sky Radiative Cooling System for Cooling the Intake Air of a Gas Turbine [Volume 53, Issue 1, 2021, Pages 155-172]
Sansebli, Mehdi Fabrication and characterization of a flexible nanogenerator using reverse electrowetting concept [Volume 53, Issue 5, 2021, Pages 3023-3034]
Sarabi, Mehrdad Investigation of the response of a multi-zone simulation code equipped with blow-by sub-model in a dual fuel spark-ignition engine [Volume 53, Issue 5, 2021, Pages 3035-3056]
Sarhaddi, Faramarz Thermal Analysis of a Solar Wall Equipped with Photovoltaic Cells and Phase-Change Materials [Volume 53, Issue 1, 2021, Pages 173-190]
Sarhaddi, Faramarz Investigation of Quality Factor for Linear Vibrations of Rectangular Micro-plates with Thermoelastic Damping [Volume 53, Issue 2, 2021, Pages 851-862]
Sarhaddi, Faramarz Numerical study and investigation of the effect of magnetic field on fluid hydrodynamic behavior [Volume 53, Issue 5, 2021, Pages 2857-2868]
Sarhaddi, Faramarz Thermal performance evaluation of a greenhouse solar dryer equipped with photovoltaic cells and phase change material [Volume 53, Issue 5 (Special Issue), 2021, Pages 3367-3384]
Sayah Badkhor, Mostafa Plastic Deformation of Reinforced Aluminum Plates with Polyurea Coating under Impulsive Loading [Volume 53, Issue 2 (Special Issue), 2021, Pages 1251-1268]
Sayah Badkhor, Mostafa Effect of intense impulsive loading on performance of multi-layered plates [Volume 53, Issue 4 (Special Issue), 2021, Pages 2639-2670]
Sayah Badkhor, Mostafa Investigation of penetration behavior of monolithic and multi-layered metallic targets subjected to a projectile impact [Volume 53, Issue 4, 2021, Pages 2309-2330]
Schmauder, Siegfried Investigation of the micromechanical behavior of ferritic-martensitic steel under complex loading [Volume 53, Issue 6, 2021, Pages 3689-3702]
Seddighi, Sadegh Simulation of Effective Parameters on Desalination Water Using Capacitive Deionization Method [Volume 53, Issue 11, 2022, Pages 5595-5612]
Sefid, Mohammad Power Improvement of a Commercial Large Scale Vertical-Axis Wind Turbine Using Plasma Actuators [Volume 53, Issue 3, 2021, Pages 1487-1504]
Selahi, Ehsan Transient Analysis and Free Vibration of Functionally Graded Truncated Conical Shells Subjected to Moving Pressure [Volume 53, Issue 2, 2021, Pages 897-912]
Sepah Mansoor, Mehran Steam generation via solar energy and localizing the light on the pinewood surface [Volume 53, Issue 3 (Special Issue), 2021, Pages 2001-2012]
Sepehrianazar, Farid Investigation of the effect of free-wind velocity on the performance of small-scale vertical axis wind turbine [Volume 53, Issue 3 (Special Issue), 2021, Pages 1709-1728]
Sepehrnia, Mojtaba Numerical Simulation of Magnetic Field Effect on Thermal and Thermo-Hydraulic Performance and Entropy Generation of a Silicon Microchannel Heat Sink Under Uniform Heat Flux [Volume 53, Issue 1 (Special Issue), 2021, Pages 517-538]
Sepehry, Naserodin Control of droplet size in a two-phase microchannel using PID controller: A novel experimental study [Volume 53, Issue 7, 2021, Pages 4279-4292]
Sepehry, Naserodin Modeling of vibro-acoustic modulation induced by non-linear contact in the Euler-Bernoulli beam using the Fourier spectral element [Volume 53, Issue 6 (Special Issue), 2021, Pages 3809-3824]
Setoodeh, Ali Reza Transient Analysis and Free Vibration of Functionally Graded Truncated Conical Shells Subjected to Moving Pressure [Volume 53, Issue 2, 2021, Pages 897-912]
Setoodeh, Ali Reza Free vibration analysis of functionally graded carbon nanotubes reinforced composite skew folded plates using the isogeometric approach [Volume 53, Issue 4, 2021, Pages 2239-2260]
Seyedi, Mirmasoud Accurate and faster than real-time simulation of indoor airflow by using fast fluid dynamics [Volume 53, Issue 3 (Special Issue), 2021, Pages 1839-1860]
Seyed Mahmoudi, Seyed Mohammad Thermodynamic Analysis of Power Generation System Based on Solid Oxide Fuel Cell With External Reforming [Volume 53, Issue 1 (Special Issue), 2021, Pages 605-622]
Seyyed Fakhrabadi, Mir Masoud Investigation of wave propagation in architected uniform triangle mass center fractal nano-bio-filters based on microtubules [Volume 53, Issue 6 (Special Issue), 2021, Pages 3939-3952]
Shafei, Ali Mohammad Modeling and trajectory tracking control of non-holonomic mobile robot with revolute-prismatic joints [Volume 53, Issue 2 (Special Issue), 2021, Pages 1041-1064]
Shafiee, Mojtaba An Experimental Investigation on the Convective Heat Transfer Coefficient and Nusselt Number in Water/Carbon Nanofluid [Volume 53, Issue 1, 2021, Pages 209-220]
Shafiei, Mohammad Behshad Numerical Simulation of Magnetic Field Effect on Thermal and Thermo-Hydraulic Performance and Entropy Generation of a Silicon Microchannel Heat Sink Under Uniform Heat Flux [Volume 53, Issue 1 (Special Issue), 2021, Pages 517-538]
Shahani, Amir reza Study of the Analytical Solutions and Modelling of Nonlinear Buckling in Bellows [Volume 53, Issue 2, 2021, Pages 729-744]
Shahbad, Ramin The Prediction of Femoral Fracture Location Using Extended Finite Element Method [Volume 53, Issue 8, 2021, Pages 4595-4608]
Shahbazi, Hamed A comparison study of deep neural controllers and classic controllers in self-driving car application [Volume 53, Issue 4 (Special Issue), 2021, Pages 2439-2458]
Shahgholi, Majid Out-of-Plane Vibration Mitigation of Wind Turbine Blade Using Highly Efficient Nonlinear Energy Sink [Volume 53, Issue 12, 2022, Pages 5851-5866]
Shahmardan, MM Experimental Study of Surfactant Type Effects on the Foam Stability and Mobility With the Approach of Enhancing Oil Recovery [Volume 53, Issue 1 (Special Issue), 2021, Pages 339-356]
Shahmardan, Mohammad Mohsen Measurement of subcooled flow boiling heat transfer coefficient in vertical annulus tube [Volume 53, Issue 7, 2021, Pages 4345-4360]
Shahmardan, Mohammad Mohsen Convection Heat transfer Fe3O4/Water in a Square microchannel Under Uniform Heat Flux and Magnetic Field [Volume 53, Issue 9, 2021, Pages 4925-4942]
Shahnazari, Mohammad Reza Analysis of Density Wave Oscillations in a Boiling Channel by a New Analytical Model [Volume 53, Issue 3, 2021, Pages 1505-1520]
Shahriyari, Mohammad Javad Circumferential Casing Treatment in a Transonic Fan [Volume 53, Issue 7, 2021, Pages 4189-4202]
Shahriyari, Mohammad Javad A Theory for Predicting Stall Cell Transient Behavior [Volume 53, Issue 9, 2021, Pages 4773-4788]
Shahryari, Mehran Numerical Investigation of Hybrid Wick Structure Effect on Thermal Performance of a Thin Flat Heat Pipe [Volume 53, Issue 11, 2022, Pages 5485-5504]
Shamshirsaz, Mahnaz Modeling of vibro-acoustic modulation induced by non-linear contact in the Euler-Bernoulli beam using the Fourier spectral element [Volume 53, Issue 6 (Special Issue), 2021, Pages 3809-3824]
Shamshirsaz, Mahnaz Investigation on Mechanical Properties of Polyoxymethylene Reinforced by Carbon Nanotube Using Molecular Dynamics [Volume 53, Issue 8, 2021, Pages 4691-4700]
Shanehsaz, Sobhan Comparison of natural and synthetic carotid arteries in the normal and occluded cases considering the effect of blood on elastic wall of artery [Volume 53, Issue 5, 2021, Pages 2821-2838]
Shariati, Mahmoud Theoretical Analysis of Equal Channel Angular Pressing Process by Upper Bound Method and Its Experimental Investigation in Condition of Circular Cross-Section Channel [Volume 53, Issue 8, 2021, Pages 4729-4744]
Shaterzadeh, Alireza On the deviation from cyclic symmetry in a spinning ring under moving electromagnetic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 3891-3910]
Sheikh Khoshkar, Saber On the deviation from cyclic symmetry in a spinning ring under moving electromagnetic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 3891-3910]
Sheikhzadeh, Ghanbar Ali Hydrothermal performance of trapezoidal fin equipped with vortex generator and hole: Investigation of the effect of vortex generator and hole position [Volume 53, Issue 3 (Special Issue), 2021, Pages 1963-1980]
Shervani Tabar, Mohammad Taghi Experimental study on the enhancement of the thermal efficiency of a household gas water heater [Volume 53, Issue 3 (Special Issue), 2021, Pages 2013-2030]
Shiravand, Ali A new method for estimating the compressive strain of cellular structures using microstructure of foams based on Laguerre tessellations [Volume 53, Issue 6, 2021, Pages 3629-3644]
Shiravi, Amir Hossein An Experimental Investigation on the Convective Heat Transfer Coefficient and Nusselt Number in Water/Carbon Nanofluid [Volume 53, Issue 1, 2021, Pages 209-220]
Shojaeefard@iust.ac.ir, Mohammad Hasan Investigation to set the type of pre-chamber fuel system in heavy gas engine HIMSEN 35/40 [Volume 53, Issue 5, 2021, Pages 2935-2952]
Shojaei, Ahmadreza Experimental Investigation of Water Level Control System of Liquid-Gas Separator in the Fuel Cell [Volume 53, Issue 1 (Special Issue), 2021, Pages 589-604]
Shokrollahi, Hassan Thermal Stress Analysis of the Carbon Nanotube Reinforced Composite Cylindrical Shells [Volume 53, Issue 10, 2022, Pages 5269-5292]
Simjoo, Mohammad Modeling of Drilling Cuttings Transport by Foam in Horizontal Well Condition Using Computational Fluid Dynamics [Volume 53, Issue 1 (Special Issue), 2021, Pages 357-374]
Sina, Naser Investigation of vehicle energy demand considering the modified tire power loss [Volume 53, Issue 6, 2021, Pages 3615-3628]
Sina, Seyed Ali On the deviation from cyclic symmetry in a spinning ring under moving electromagnetic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 3891-3910]
S. Mahmoudi, S. Mohammad Advanced exergy and thermoeconomic analysis of the supercritical carbon dioxide recompression cycle: A comparative study [Volume 53, Issue 5, 2021, Pages 2967-2982]
Sobhnamayan, Fatemeh Thermal Analysis of a Solar Wall Equipped with Photovoltaic Cells and Phase-Change Materials [Volume 53, Issue 1, 2021, Pages 173-190]
Sobhnamayan, Fatemeh Thermal performance evaluation of a greenhouse solar dryer equipped with photovoltaic cells and phase change material [Volume 53, Issue 5 (Special Issue), 2021, Pages 3367-3384]
Sohrabifard, Mahfooz An Experimental Approach for Determination of Locators Reaction Forces in Milling Fixtures [Volume 53, Issue 12, 2022, Pages 5615-5626]
Sojoodi, Mahdi Numerical Study on the Complete Separation of Blood Cells using the Integrated Dielectrophoretic-Photophoretic Method in a New Microchannel [Volume 53, Issue 1 (Special Issue), 2021, Pages 655-670]
Soltani, Abbas Combination of active braking and semi-active suspension systems to improve the roll and yaw vehicle stability [Volume 53, Issue 6, 2021, Pages 3549-3570]
Soltani, Azadeh Lateral Stability Analysis of Thin-Walled Fiber-Metal Laminate Beam with Varying Cross-Section by Considering Nonlinear Strains [Volume 53, Issue 10, 2022, Pages 5239-5268]
Soltani, Majid Image-based numerical model for drug delivery to solid tumors [Volume 53, Issue 5 (Special Issue), 2021, Pages 3187-3200]
Soltani, Masoumeh Free vibration and flexural-torsional stability analyses of axially functionally graded tapered thin-walled beam resting on elastic foundation [Volume 53, Issue 6, 2021, Pages 3587-3614]
Soltani, Masoumeh Lateral Stability Analysis of Thin-Walled Fiber-Metal Laminate Beam with Varying Cross-Section by Considering Nonlinear Strains [Volume 53, Issue 10, 2022, Pages 5239-5268]
Soltanian, Hossein Experimental Investigation of Combustion Species Radiation to Evaluate Equivalence Ratio in a Surface Flame Burner [Volume 53, Issue 1, 2021, Pages 41-52]
Tadjfar, Mehran Implementation of Continuous Blowing and Synthetic Jet Actuators to Control the Flow Separation over a Fully Stalled Airfoil [Volume 53, Issue 9, 2021, Pages 4847-4864]
Tadjfar, Mehran Experimental Investigation of a High Aspect Ratio Rectangular Liquid Jet in Parallel Airflow [Volume 53, Issue 11, 2022, Pages 5429-5444]
Taghavipour, Amir Analyzing driving behavior based on vehicle information logging using MPU6050 [Volume 53, Issue 6 (Special Issue), 2021, Pages 3855-3874]
Taghavi Zenouz, Reza Experimental and Numerical Investigation of Film Cooling Effectiveness on Squealer Tip of a Turbine Blade [Volume 53, Issue 3, 2021, Pages 1521-1536]
Taghizadeh, Mohsen Investigating the Influence of Higher-Order Boundary Conditions on Free Vibrations of Bi-Directional Functionally Graded Thick Conical Micro-Shells [Volume 53, Issue 10, 2022, Pages 5085-5104]
Taghizadeh, Mostafa Kinematic and dynamic performance evaluation of a four degrees of freedom parallel robot [Volume 53, Issue 4, 2021, Pages 2055-2072]
Taghizadeh, Mostafa Assessing short-term storage effects on hydrostatic wind turbine in presence of turbulent wind [Volume 53, Issue 6, 2021, Pages 3431-3444]
Taghizadeh, Mostafa Active Fault Tolerant Control of Wind Turbine Systems using Disturbance Observer-based Sliding Mode and Time Delay Estimation [Volume 53, Issue 8, 2021, Pages 4517-4534]
Taghizadeh, Mostafa Active fault tolerant control based on adaptive back-stepping nonsingular fast integral terminal sliding mode approach [Volume 53, Issue 6 (Special Issue), 2021, Pages 3763-3782]
Taghizadeh, Mostafa Robust and Adaptive Control of an Exoskeleton Robot For Tracking Modified Desired Trajectory Based on Zero Moment Point Stability Theory [Volume 53, Issue 12, 2022, Pages 5831-5850]
Tahani, Masoud Transient Analysis and Free Vibration of Functionally Graded Truncated Conical Shells Subjected to Moving Pressure [Volume 53, Issue 2, 2021, Pages 897-912]
Taheri, Moein Experimental Extraction of Young's Modulus of MCF-7 Breast Cancer Cell Using Spherical Contact Models [Volume 53, Issue 12, 2022, Pages 5769-5784]
Taheri, Seyedmahdi Investigation of the mechanical properties of multilayer graphene helicoids with different geometric characteristics using molecular dynamics simulation [Volume 53, Issue 2 (Special Issue), 2021, Pages 1237-1250]
Taherkhani, Zahra Sensitivity Analysis of Rotor Dynamic Behavior to Manufacturing Tolerances Based on Global Sensitivity Analysis and Statistical Methods [Volume 53, Issue 8, 2021, Pages 4501-4516]
Tahmasbi, Vahid Process modeling of force behavior in the automatic bovine cortical bone milling process using adaptive neuro-fuzzy inference system [Volume 53, Issue 2 (Special Issue), 2021, Pages 1287-1306]
Tahmasebpour, Maryam Modeling the calcium looping process with an emphasis on the bed hydrodynamics and sorbent characteristics [Volume 53, Issue 5, 2021, Pages 2807-2820]
Tahmasebpour, Maryam Removal of Lead Heavy Metal from Wastewater by Crystallization Process and Investigation of the Effective Parameters [Volume 53, Issue 11, 2022, Pages 5349-5366]
Tajik, Hamid Reza Numerical Investigation of Hybrid Wick Structure Effect on Thermal Performance of a Thin Flat Heat Pipe [Volume 53, Issue 11, 2022, Pages 5485-5504]
Talebi-Ghadikolaee, Hossein Experimental and numerical investigation of the plastic deformation of metallic bipolar plates with serpentine flow filed [Volume 53, Issue 6, 2021, Pages 3717-3732]
Tavakkol, Fardad Numerical analysis of flow and natural convection heat transfer in a circular enclosure heated from bottom utilizing porous layer [Volume 53, Issue 3 (Special Issue), 2021, Pages 1937-1962]
Tavakoli dastjerd, Fateme Steam generation via solar energy and localizing the light on the pinewood surface [Volume 53, Issue 3 (Special Issue), 2021, Pages 2001-2012]
Tavari, AmirHossein Three-dimensional surface capture from the back anatomy to quantify three-dimensional vertebral column curvatures without using anatomical markers [Volume 53, Issue 4 (Special Issue), 2021, Pages 2629-2638]
Taylor, Robert Investigation of using hybrid nanofluid-phase change material spectral splitter in photovoltaic/thermal system [Volume 53, Issue 7, 2021, Pages 4429-4454]
Teymoori, Saeed Experimental Investigation of the Effects of Inlet Cooling Air Temperature on the Occupants’ Local Thermal Sensation in the Under-Floor Air Distribution System [Volume 53, Issue 3, 2021, Pages 1537-1548]
Teymourtash, Ali Reza Experimental Study of the Effect of Fluid Jet Swirl on Circular Hydraulic Jump [Volume 53, Issue 7, 2021, Pages 4153-4170]
Torabi, Ali Reza Experimental and theoretical investigation of the critical load of U-notched laminated composite specimens under in-plane shear loading [Volume 53, Issue 6, 2021, Pages 3673-3688]
Torabi, Ali Reza Experimental and Theoretical Assessment of Mode II Fracture Toughness for Cracked Ductile Specimens with High Strain-Hardening [Volume 53, Issue 10, 2022, Pages 5141-5158]
Torabi, Amir Transient numerical modeling and experimental investigation of the effect of surface texture on elastohydrodynamic lubrication [Volume 53, Issue 5 (Special Issue), 2021, Pages 3201-3212]
Torabi Azad, Masoud Investigation of hydrogen production process by partial oxidation of natural gas in a large non-catalytic reformer and comparison with methane steam reforming process in a small catalytic reformer [Volume 53, Issue 5 (Special Issue), 2021, Pages 3275-3292]
Torfeh, Soodeh Performance Evaluation of a Fluidized Bed Reactor by Studying the Hydrodynamics and Thermal Properties of Different Solid Particles [Volume 53, Issue 3, 2021, Pages 1573-1590]
V
Vahdati, Mahdi Statistical analysis and optimization of tensile strength of Al7075 butt joint produced by friction stir welding and submerged friction stir welding via response surface methodology and desirability approach [Volume 53, Issue 4 (Special Issue), 2021, Pages 2719-2734]
Vahidi, Bahman Response analysis of primary cilia of the cell to the oscillatory fluid flow by using fluid-structure interaction method [Volume 53, Issue 5 (Special Issue), 2021, Pages 3293-3306]
Vahidi, Bahman Computational Fluid Dynamics Analysis of Effects of Housing Expansion Angle, Stroke Volume and Path Length of the Fiber Bundles on Function of the Artificial Lung [Volume 53, Issue 11, 2022, Pages 5389-5408]
Vahidi, Bahman Fluid-Structure Interactions Analysis of Tension in An Axon Using Finite Elements Modeling to Investigate Strain Related Neurological Damages [Volume 53, Issue 8, 2021, Pages 4609-4632]
Varedi Kulaee, Seyed Mojtaba Kinematic Optimization of the Stirling engine for Maximum Output Work and Constraint of Occupied Space [Volume 53, Issue 7, 2021, Pages 4455-4480]
Vaseghnia, Hamed Study of cavitation inception using multiphase lattice Boltzmann method with incorporating equations of state [Volume 53, Issue 5 (Special Issue), 2021, Pages 3151-3170]
Vaziri, Ehsan Modeling of Drilling Cuttings Transport by Foam in Horizontal Well Condition Using Computational Fluid Dynamics [Volume 53, Issue 1 (Special Issue), 2021, Pages 357-374]
Y
Yadavar nikravesh, Seyed majid Experimental and Numerical Looseness Detection and Assessment in Flanged Joints Using Vibro-Acoustic Modulation Method [Volume 53, Issue 2 (Special Issue), 2021, Pages 1331-1344]
Yaldaei, Ali Asghar Investigation of Quality Factor for Linear Vibrations of Rectangular Micro-plates with Thermoelastic Damping [Volume 53, Issue 2, 2021, Pages 851-862]
Yarahmadi, Masoud Measurement of subcooled flow boiling heat transfer coefficient in vertical annulus tube [Volume 53, Issue 7, 2021, Pages 4345-4360]
Yari, Mortaza Investigation of Performance and Emission Characteristic of a Reactivity Controlled Compression Ignition Engine Fueled By a Mixture of Diesel and Syngas Derived From Biomass Gasification [Volume 53, Issue 1, 2021, Pages 17-30]
Yari, Mortaza Experimental study on the enhancement of the thermal efficiency of a household gas water heater [Volume 53, Issue 3 (Special Issue), 2021, Pages 2013-2030]
Yarmohammadi, M.javad Assessing short-term storage effects on hydrostatic wind turbine in presence of turbulent wind [Volume 53, Issue 6, 2021, Pages 3431-3444]
Yazdani, Hamidreza Power Improvement of a Commercial Large Scale Vertical-Axis Wind Turbine Using Plasma Actuators [Volume 53, Issue 3, 2021, Pages 1487-1504]
Yazdani, Mahdi Approximate Torsional Analysis of Arbitrary Trapezoidal Bars by Kantorovich Method [Volume 53, Issue 10, 2022, Pages 5203-5220]
Yazdanifard, Farideh Investigation of using hybrid nanofluid-phase change material spectral splitter in photovoltaic/thermal system [Volume 53, Issue 7, 2021, Pages 4429-4454]
Z
Zabetian Toroghi, Mohammad Numerical Study on the Complete Separation of Blood Cells using the Integrated Dielectrophoretic-Photophoretic Method in a New Microchannel [Volume 53, Issue 1 (Special Issue), 2021, Pages 655-670]
Zabetian Toroghi, Mohammad Experimental Investigation of Combustion Species Radiation to Evaluate Equivalence Ratio in a Surface Flame Burner [Volume 53, Issue 1, 2021, Pages 41-52]
Zabihian, Ehsan CubeSat antenna vibration control using piezoelectric bender considering system requirements [Volume 53, Issue 4, 2021, Pages 2217-2238]
Zahed, Babak Design and Multi-Objective Optimization of A Magnetohydrodynamic Drug Delivery Infusion Micropump [Volume 53, Issue 10, 2022, Pages 5221-5238]
Zahedi Siani, Omid Numerical Study on the Complete Separation of Blood Cells using the Integrated Dielectrophoretic-Photophoretic Method in a New Microchannel [Volume 53, Issue 1 (Special Issue), 2021, Pages 655-670]
Zahmatkesh, Iman Numerical simulation of nanofluid flow in an annulus with porous baffles based on combination of Darcy-Brinkman-Forchheimer model and two-phase mixture model [Volume 53, Issue 3 (Special Issue), 2021, Pages 1897-1914]
Zajkani, Asghar Analysis of Forming Limit of Sheet Metals Considering Vertex Localized Necking and Ductile Damage Criterion [Volume 53, Issue 2 (Special Issue), 2021, Pages 1307-1320]
Zakerzadeh, Mohammad Reza Finite Element Modeling of a Novel Magnetic Shape Memory Alloy Based Energy Harvester Using a Corrugated Beam and Investigating the Effective Parameters [Volume 53, Issue 2, 2021, Pages 799-814]
Zakerzadeh, Mohammad Reza Finite element modeling of shape memory alloy stent insertion in the vessel with consideration of vessel damage [Volume 53, Issue 2 (Special Issue), 2021, Pages 1211-1222]
Zamani, Ali Stability and bifurcation of a rotating blade with varying speed [Volume 53, Issue 4 (Special Issue), 2021, Pages 2459-2472]
Zamanian, Rahim Network Modeling to Investigate the Effect of Coupling the Transport Phenomena on Water Distribution in Gas Diffusion Layer [Volume 53, Issue 11, 2022, Pages 5505-5528]
Zaminpayma, Esmaiel Investigation on Mechanical Properties of Polyoxymethylene Reinforced by Carbon Nanotube Using Molecular Dynamics [Volume 53, Issue 8, 2021, Pages 4691-4700]
Zandi, Majid Experimental study on effective parameters on vertical axis wind turbine performance [Volume 53, Issue 5, 2021, Pages 2771-2790]
Zarafshan, Payam Dynamic modeling and control of cleaning robot for agro-photovoltaic [Volume 53, Issue 6, 2021, Pages 3465-3478]
Zareh, Masud Energy and Exergy Analysis of Organic Rankine Cycle Fed by Electric Arc Furnace Waste Heat [Volume 53, Issue 9, 2021, Pages 4999-5016]
Zarepour, Gholamreza Semi-Analytical Study of Fluid-Induced Nonlinear Vibrations in Viscoelastic Beams with Standard Linear Solid Model Using Multiple Time Scales Method [Volume 53, Issue 10, 2022, Pages 5105-5122]
Zare Talab, zeinab Numerical Simulation of Heat Transfer Turbulent Flow for Non-Newtonian Nanofluid in a Double Pipe Helical Heat Exchanger [Volume 53, Issue 1, 2021, Pages 221-240]
Ziya-Shamami, Mojtaba Experimental investigation and mathematical modeling of the response of circular metallic plates under successive intense dynamic loading [Volume 53, Issue 6 (Special Issue), 2021, Pages 4023-4050]
Zohrevandi, Delaram Design, Fabrication and Experimental Study of Spiral Microchannel Particle Separator on Centrifugal Microfluidic Platforms [Volume 53, Issue 3, 2021, Pages 1359-1372]
Zolfaghari, Alireza Effect of Air Curtain on Occupants Thermal Comfort and Indoor Air Quality in an Athletic Swimming Pool with Spectators’ Stand [Volume 53, Issue 1, 2021, Pages 191-208]
Zolfaghari, Alireza Experimental Investigation of the Effects of Inlet Cooling Air Temperature on the Occupants’ Local Thermal Sensation in the Under-Floor Air Distribution System [Volume 53, Issue 3, 2021, Pages 1537-1548]
Zolfaghari, Alireza Effect of Gender and Body Fitness on the Thermal Sensation of Sleeping Occupants Under Task-Ambient Air Conditioning System [Volume 53, Issue 1 (Special Issue), 2021, Pages 453-466]
Zolfaghari, Alireza Developing an alternating direction explicit-implicit domain-decomposition approach to solve heat transfer equation on graphics processing unit [Volume 53, Issue 3 (Special Issue), 2021, Pages 1915-1936]
Zolfaghari, Alireza Experimental evaluation of the effect of supply air direction on air current and temperature in a room with underfloor air distribution system [Volume 53, Issue 5, 2021, Pages 3057-3076]
Zolfaghari, Alireza Experimental investigation of personalized ventilation effects on temperature, velocity, and draught discomfort distribution in an office [Volume 53, Issue 7, 2021, Pages 4397-4410]
Zolfagharian, Mohammad Mehdi Manufacturing and Testing of an Optimized Magneto-Rheological Fluid and Modelling of a Twin Tube Magneto-Rheological Damper Using a Modified Non-Newtonian Model Using Analytical Quasi-Static, Analytical Unsteady, Numerical and Experimental Methods [Volume 53, Issue 3, 2021, Pages 1373-1400]
Zysset, Philippe Mechanical Properties and Structural Behavior of Bone at Nano Scale with Cohesive Element [Volume 53, Issue 2, 2021, Pages 745-776]
