Improvement in the flexural properties of basalt fibers/epoxy-aluminum laminate composites using multi-walled carbon nanotubes

Document Type : Research Article

Authors

Faculty of Materials Science and Engineering, K. N. Toosi University of Technology, Tehran, Iran

Abstract

Recently, to improve the mechanical properties of polymeric composites, the inclusion of various nano particles into the polymer matrices has received much attention. But, it is not well established whether nano particles can enhance the mechanical properties of fiber metal laminates (FMLs). The present study aims to investigate the effect of multi-walled carbon nano tubes (MWCNTs) on the flexural behavior of a FML made up of alternating layers of Al 2024 along with basalt fibers reinforced epoxy. Results showed that the flexural strength and flexural modulus of samples have an upward trend up to 0.5 wt. % loading, but beyond that a downward trend was observed. Therefore, in this research, the optimal content of MWCNTs for the best flexural properties was the 0.5 wt. % and comparing to the samples without MWCNTs, the flexural strength and flexural modulus values was found to 36.62 % and 60.16 % improvement, respectively. Also, Scanning Electron Microscopy (SEM) observations showed that the mechanisms of CNT-pull-out and CNT-bridging was the main reason for this findings.

Keywords

Main Subjects

References

[1] T. Sinmazçelik, E. Avcu, M.Ö. Bora, O. Çoban, A review: Fibre metal laminates, background, bonding types and applied test methods, Materials & Design, 32(7) (2011) 3671-3685.
[2] X. Li, W. Zhang, S. Zhai, S. Tang, X. Zhou, D. Yu, X. Wang, Investigation into the toughening mechanism of epoxy reinforced with multi-wall carbon nanotubes, e-Polymers, 15(5) (2015) 335-343.
[3] L. Meszaros, I.M. Gali, T. Czigany, T. Czvikovszky, Effect of nanotube content on mechanical properties of basalt fibre reinforced polyamide 6, Plastics, Rubber and Composites, 40(6-7) (2013) 289-293.
[4] M. Sánchez, M. Campo, A. Jiménez-Suárez, A. Ureña, Effect of the carbon nanotube functionalization on flexural properties of multiscale carbon fiber/epoxy composites manufactured by VARIM, Composites Part B: Engineering, 45(1) (2013) 1613-1619.
[5] N. Jahan, M.V. Hosur, S. Jeelani, Low-Velocity Impact Response of Woven Carbon Epoxy Composites with MWCNTs, (2013) 1586-1592.
[6] M. Konstantakopoulou, G. Kotsikos, Effect of MWCNT filled epoxy adhesives on the quality of adhesively bonded joints, Plastics, Rubber and Composites, 45(4) (2016) 166-172.
[7] M.M. Rahman, S. Zainuddin, M.V. Hosur, J.E. Malone, M.B.A. Salam, A. Kumar, S. Jeelani, Improvements in mechanical and thermo-mechanical properties of e-glass/epoxy composites using amino functionalized MWCNTs, Composite Structures, 94(8) (2012) 2397-2406.
[8] Y. Zhou, F. Pervin, L. Lewis, S. Jeelani, Experimental study on the thermal and mechanical properties of multi-walled carbon nanotube-reinforced epoxy, Materials Science and Engineering: A, 452-453 (2007) 657-664.
[9] M.T. Kim, K.Y. Rhee, J.H. Lee, D. Hui, A.K.T. Lau, Property enhancement of a carbon fiber/epoxy composite by using carbon nanotubes, Composites Part B: Engineering, 42(5) (2011) 1257-1261.
[10] A. Godara, L. Mezzo, F. Luizi, A. Warrier, S.V. Lomov, A.W. van Vuure, L. Gorbatikh, P. Moldenaers, I. Verpoest, Influence of carbon nanotube reinforcement on the processing and the mechanical behaviour of carbon fiber/epoxy composites, Carbon, 47(12) (2009) 2914-2923.
[11] M.M. Shokrieh, A. Saeedi, M. Chitsazzadeh, Evaluating the effects of multi-walled carbon nanotubes on the mechanical properties of chopped strand mat/polyester composites, Materials & Design, 56 (2014) 274-279.
[12] G.B. Chai, P. Manikandan, Low velocity impact response of fibre-metal laminates:A review, Composite Structures, 107 (2014) 363-381.
[13] X. Li, X. Zhang, H. Zhang, J. Yang, A.B. Nia, G.B. Chai, Mechanical behaviors of Ti/CFRP/Ti laminates with different surface treatments of titanium sheets, Composite Structures, 163 (2017) 21-31.
[14] M. Sadighi, R.C. Alderliesten, R. Benedictus, Impact resistance of fiber-metal laminates: A review, International Journal of Impact Engineering, 49 (2012) 77-90.
[15] H. Zarei, M. Fallah, G. Minak, H. Bisadi, A. Daneshmehr, Low velocity impact analysis of Fiber Metal Laminates (FMLs) in thermal environments with various boundary conditions, Composite Structures, 149 (2016) 170-183.
[16] L.L. Zhai, G.P. Ling, Y.W. Wang, Effect of nano-Al2O3 on adhesion strength of epoxy adhesive and steel, International Journal of Adhesion and Adhesives, 28(1-2) (2008) 23-28.
[17] A. Fereidoon, N. Kordani, Y. Rostamiyan, D. Ganji, M. Ahangari, Effect of carbon nanotubes on adhesion strength of e-glass/epoxy composites and alloy aluminium surface, World Appl Sci J, 9(2) (2010) 204-210.
[18] Z. Asaee, M. Mohamed, D. De Cicco, F. Taheri, Low-velocity impact response and damage mechanism of 3D fiber-metal laminates reinforced with amino-functionalized graphene nanoplatelets, International Journal of Composite Materials, 7(1) (2017) 20-36.
[19] R. Amooyi Dizaji, M. Yazdani, E. Aligholizadeh, A. Rashed, Effect of 3D‐woven glass fabric and nanoparticles incorporation on impact energy absorption of GLARE composites, Polymer Composites, (2017) (in press).
[20] S. Abrate, Impact engineering of composite structures, Springer Science & Business Media, 2011.
Amirkabir Journal of Mechanical Engineering
Volume 51, Issue 3
July and August 2019
Pages 81-90

Files

Share

How to cite

Statistics