Experimental and Numerical Study of Hydrodynamic Deep Drawing Process of Rectangular Cups and Blank Shape Optimization

Document Type : Research Article

Authors

Faculty of Mechanical Engineering, Babol Noshirvani University of Technology, Babol, Iran

Abstract

Production of rectangular sheet parts by traditional deep drawing methods is associated
with many problems. The absence of axisymmetry and the difference between the length and width of
the part makes the forming of these products difficult. In this paper, forming of rectangular cups in a
single step which is not possible by traditional methods for the desired depth and corner radius, has been
examined by hydrodynamic deep drawing process with radial pressure. In this research, after designing
and manufacturing of die and forming of rectangular parts, the obtained results from simulation were
compared and verified by those of experiments. Moreover, the effect of forming pressure on thickness
distribution has been investigated. The study illustrated that increasing forming pressure up to an optimum
value improves formability and thickness distribution. In addition, in order to remove flange area and to
improve formability, optimization of the sheet dimensions has been performed using sensitivity analysis.
It was concluded that optimizing the blank shape can improve thickness distribution, eliminate final
flange trimming and decrease one stage of manufacturing, resulting in decreasing production time and
cost. Finally, it was illustrated that it is possible to adequately form rectangular cups in one stage using
optimized blanks.

Keywords

Main Subjects


[1] S.H. Zhang, Developments in hydroforming, Journal of Materials Processing Technology, 91(1–3) (1999) 236-244.
[2] A. Kandil, An experimental study of hydroforming deep drawing, Journal of materials processing Technology,134(1) (2003) 70-80.
[3] B.N.Huiting-Wang, B.LinGao, B.Minghe-Chen, Hydrodynamic deep drawing process assisted by radial pressure with inward flowing liquid, International Journal of Mechanical Sciences, 53 (2011) 793-799.
[4] L. Lang, J. Danckert, K.B. Nielsen, Investigation into hydrodynamic deep drawing assisted by radial pressure:Part I. Experimental observations of the forming process of aluminum alloy, Journal of Materials Processing Technology, 148(1) (2004) 119-131.
[5] B.-S. Kang, W.-J. Song, T.-W. Ku, Study on process parameters and its analytic application for nonaxisymmetric rectangular cup of multistage deep drawing process using low carbon thin steel sheet, The International Journal of Advanced Manufacturing Technology, 49(9-12) (2010) 925-940.
[6] B. Meng, M. Wan, S. Yuan, X. Xu, J. Liu, Z. Huang, Influence of cavity pressure on hydrodynamic deep drawing of aluminum alloy rectangular box with wide flange, International Journal of Mechanical Sciences, 77(2013) 217-226.
[7] F. Rahmani, S. Hashemi, H. Moslemi Naeini, H. Deylami Azodi, Numerical and Experimental Study of the Efficient Parameters on Hydromechanical Deep Drawing of Square Parts, Journal of Materials Engineering and Performance, 22(2) (2013) 338-344.
[8] T.J. Kim, D.Y. Yang, S.S. Han, Numerical modeling of the multi-stage sheet pair hydroforming process, Journal of Materials Processing Technology, 151(1–3) (2004)48-53.
[9] B.-S. Kang, B.-M. Son, J. Kim, A comparative study of stamping and hydroforming processes for an automobile fuel tank using FEM, International Journal of Machine Tools and Manufacture, 44(1) (2004) 87-94.
[10] H. Shim, K. Sona, K. Kim, Optimum blank shape design by sensitivity analysis, Materials Processing Technology,104 (2000) 191-199.
[11] V. Pegada, Y. Chun, S. Santhanam, An algorithm for determining the optimal blank shape for the deep drawing of aluminum cups, Journal of Materials Processing Technology, 125–126 (2002) 743-750.
[12] E. Önder, A.E. Tekkaya, Numerical simulation of various cross sectional workpieces using conventional deep drawing and hydroforming technologies, International Journal of Machine Tools and Manufacture, 48(5) (2008)532-542.
[13] L. Xiaojing, X. Yongchao, Y. Shijian, Effects of loading paths on hydrodynamic deep drawing with independent radial hydraulic pressure of aluminum alloy based on numerical simulation, J Mater Sci Technol, 24 (2008)395-399.
[14] Y. Aue-U-Lan, G. Ngaile, T. Altan, Optimizing tube hydroforming using process simulation and experimental verification, Journal of Materials Processing Technology,146(1) (2004) 137-143.