Abbasi, A. Investigation of the Wear Behavior of Graphite Steel (GSH48) in Ultrasonic Peening Process [Volume 50, Issue 3, 2018, Pages 529-540]
Abbasi, M. An Analytical Investigation into Effects of Fracture Dispersion Coefficients and Thermal Conductivity on Geothermally Fractured Reservoirs [Volume 50, Issue 2, 2018, Pages 359-368]
Abbasi, N. Experimental Investigation and Finite Difference Modeling of Cutting Tool Temperature Distribution During Ultrasonically Assisted Turning [Volume 50, Issue 3, 2018, Pages 657-670]
Abbassi, A. Numerical Study on the Effect of Air Diffuser Angle on the Flow Field and Contaminant Dispersion in a Ventilated Room [Volume 50, Issue 4, 2018, Pages 873-882]
Abdolmehdi Hashemi, S. Energy and Exergy Analyzes and Evaluation of Traditional Flatbread Bakeries [Volume 50, Issue 6, 2019, Pages 1389-1402]
Abedini, R. Design and Construction of an Electronic Tiltmeter Calibrator and Estimation of Calibration Uncertainty [Volume 50, Issue 5, 2019, Pages 1113-1122]
Abediny, S. Design and Implementation of Intelligent Systems Detect the Driver’s Lack of Concentration [Volume 50, Issue 5, 2019, Pages 1145-1154]
Adeli, S. Thermal Analysis for Diesel Engine Exhaust Manifold with Regard to the Boiling Phenomenon and Compared with Experimental Results [Volume 50, Issue 4, 2018, Pages 711-726]
Afra, B. Proposing Immersed Boundary-Lattice Boltzmann-Lattice Spring Algorithm for Simulation of 2-D Deformable Plate in Steady Flow [Volume 50, Issue 4, 2018, Pages 683-696]
Afshari, H. Thermo-Mechanical Stress Analysis in a Rotating Radially Graded FG-Disc with Non-Uniform Thickness [Volume 50, Issue 1, 2018, Pages 33-46]
Aghajanloo, B. Fabrication of Bipolar Plates of the Fuel Cell from Stainless Steel 304 by Hot Metal Gas Forming Process [Volume 50, Issue 3, 2018, Pages 589-600]
Ahmadi Khatir, F. Experimental Investigation and Numerical Simulation of the Pressure Force on the Formation of Metallic Bipolar Plate in the Stamping Process [Volume 50, Issue 3, 2018, Pages 505-516]
Aieneravaie, M. Failure Analysis of a Gas Turbine Blade Made of Inconel 738LC Super Alloy [Volume 50, Issue 1, 2018, Pages 103-112]
Akbari, M. Three Dimensional Numerical Simulation of a Drop and Drop-to-Wall Interaction under Uniform Electric Field [Volume 50, Issue 4, 2018, Pages 755-766]
Alinejad, G. M. Numerical and Experimental Investigation of Effective Parameters on Formability of Al-St Two Layer Sheet Metals [Volume 50, Issue 3, 2018, Pages 517-528]
Alipoor, A. Experimental Investigation of Using Phase Change Materials in Heating System of a Solar Greenhouse [Volume 50, Issue 2, 2018, Pages 327-336]
Alipoor, A. Experimental Study of Charge of Paraffin Wax Along with Nanoparticles in an Eccentric Double Tube Heat Exchanger for Storing Energy in a Solar Water Heater [Volume 50, Issue 6, 2019, Pages 1403-1410]
Alipour, A. An Axiomatic Design Approach to Reduce Repetition in Tail Conceptual Design Process [Volume 50, Issue 1, 2018, Pages 3-14]
Alipour Lalami, A. Investigation of the Effect of Velocity Slip and Temperature Jump on the Heat Transfer of Nanofluid in a Microchannel Under Constant Heat Flux with Lattice Boltzmann Method [Volume 50, Issue 2, 2018, Pages 255-270]
Alizadeh, E. Experimental Study of the New Design 2.5kW Dead-End H2 /O2 PEM Fuel Cell Stack with New Design to Improve Fuel Utilization [Volume 50, Issue 2, 2018, Pages 369-376]
Alizadeh, Ebrahim Experimental Investigation and Numerical Simulation of the Pressure Force on the Formation of Metallic Bipolar Plate in the Stamping Process [Volume 50, Issue 3, 2018, Pages 505-516]
Alizadeh, H. Stress Measurement on Carbon Steel Specimen by Consideration of Magnetic-Barkhausen-Noise [Volume 50, Issue 5, 2019, Pages 1079-1084]
Amanifard, N. Numerical Investigation of the Effect of Plasma Actuator on the Film Cooling Effectiveness By Fan-Shaped Hole [Volume 50, Issue 6, 2019, Pages 1213-1228]
Amanifard1, N. Numerical Investigation of Upstream Ramp Effects on the Cooling Performance by Cylindrical and Fan-Shaped Hole [Volume 50, Issue 4, 2018, Pages 883-892]
Amidpour, M. Optimization of a Hybrid Multi-effect Desalination with Thermal Vapor Compression and Reverse Osmosis Desalination System Integrated to A Gas Turbine Cycle [Volume 50, Issue 6, 2019, Pages 1333-1350]
Amini, S. Manufacturing a Single Ultrasonic Tool Set of Vibrational friction stir welding in Bending and Axial Modes [Volume 50, Issue 3, 2018, Pages 601-618]
Amini, S. Investigation of the Wear Behavior of Graphite Steel (GSH48) in Ultrasonic Peening Process [Volume 50, Issue 3, 2018, Pages 529-540]
Amiri Hezaveh, A Phenomenological Study of Droplet Behavior Passing through a Porous Medium at Pore-Scale, Using Lattice Boltzmann Method [Volume 50, Issue 4, 2018, Pages 697-710]
Anbarsooz, M. Numerical Simulation of a Piston-Type Wavemaker using Lattice-Boltzmann Method with Moving Nested Grids [Volume 50, Issue 4, 2018, Pages 799-812]
Araee, A. Shunting Effect in Resistance Spot Welded Joints of Aluminum Alloys [Volume 50, Issue 3, 2018, Pages 561-576]
Aryanpour, M. Investigation of Torsional Static Behavior of Nano-rods Embedded in Elastic Medium Considering Surface Energy Effect [Volume 50, Issue 5, 2019, Pages 961-972]
Asadi, A. Performance Optimization of Multi-Effect Distillation-Thermal Vapor Compression Desalination Using Genetic Algorithm [Volume 50, Issue 2, 2018, Pages 399-412]
Asari, M.R. Thermal Analysis for Diesel Engine Exhaust Manifold with Regard to the Boiling Phenomenon and Compared with Experimental Results [Volume 50, Issue 4, 2018, Pages 711-726]
Asgari, M. Brain Trauma in Vehicle Side Crash; Developing a Computational Model for Diffuse Axonal and Subdural Hematoma Injuries [Volume 50, Issue 1, 2018, Pages 91-102]
Asghari, M. Finite Element Analysis of Vibration Behavior of Micro-Rotors Utilizing a Developed Strain Gradient-Based Beam Element [Volume 50, Issue 1, 2018, Pages 113-124]
Assari, M. R. Experimental Investigation of Using Phase Change Materials in Heating System of a Solar Greenhouse [Volume 50, Issue 2, 2018, Pages 327-336]
Assari, M. R. Experimental Study of Charge of Paraffin Wax Along with Nanoparticles in an Eccentric Double Tube Heat Exchanger for Storing Energy in a Solar Water Heater [Volume 50, Issue 6, 2019, Pages 1403-1410]
Atabakhshian, V. Stability Analyses and Dynamic Response of Fluid Conveyed Thin-Walled Piezoelectric Cylinder Under Harmonic Excitation [Volume 50, Issue 1, 2018, Pages 151-162]
Ayatollahi, M.R. Brittle Fracture in Key-hole Notched Polymer Specimens under Combined Compressive-shear Loading [Volume 50, Issue 5, 2019, Pages 927-942]
Azad, E. Experimental Study of Freeing Stuck Pipe by Changing in Characterization and Additives of Mud Cake [Volume 50, Issue 4, 2018, Pages 863-872]
Azimi, A. Numerical Simulation of Transient Compressible Flow in Natural Gas long Transmission Pipelines Using a Suitable Parallel Algorithm [Volume 50, Issue 4, 2018, Pages 785-798]
Azimifar, A. Minimization of Rate of Heat Transfer from Rectangular Cavities with Free Convection in Various Aspect Ratios for Finding Characteristics of an Array of Adiabatic Thin Fins by PSO Algorithm [Volume 50, Issue 2, 2018, Pages 295-308]
Azizi, A. Bending and Free Vibration Analysis of Functionally Graded Nano-plate Using Trigonometric Higher-Order Plate Theory [Volume 50, Issue 5, 2019, Pages 1039-1050]
B
Bagheri Ardakani, A. Numerical Analysis and Optimization of Magnetic Flux Density in the Polishing Process with Magnetorheological Fluid [Volume 50, Issue 3, 2018, Pages 577-588]
Bakhshi, M. Numerical and Experimental Investigation of Effective Parameters on Formability of Al-St Two Layer Sheet Metals [Volume 50, Issue 3, 2018, Pages 517-528]
Bakhtiari, M. Investigation of Step Sweep-Forward Angle Effects on the Hydrodynamic Performance of a Planing hull [Volume 50, Issue 4, 2018, Pages 903-912]
Bannazadeh, R. Failure Analysis of a Gas Turbine Blade Made of Inconel 738LC Super Alloy [Volume 50, Issue 1, 2018, Pages 103-112]
Bannazadeh, R. Experimental Study of Cryogenic Cooling Effect on Tool Wear and Power Consumption During Turning of AISI304 [Volume 50, Issue 3, 2018, Pages 641-657]
Barzegari, M. Experimental Investigation and Numerical Simulation of the Pressure Force on the Formation of Metallic Bipolar Plate in the Stamping Process [Volume 50, Issue 3, 2018, Pages 505-516]
Basirjafari, S. Increasing the Frequency Band of Sound Absorption for Flat Multi-Layered Absorbers Consisting of Porous Material, Perforated Panel and Air-Gap [Volume 50, Issue 1, 2018, Pages 219-230]
Bayani, H. Multiphase Simulation of Aluminum A356 Metal Foam Formation Process by Lattice Boltzmann Method [Volume 50, Issue 4, 2018, Pages 741-754]
Bazargan, M. Investigation of the Effect of Longitudinal Distance Between Two Cars on Fuel Consumption and Drag Coefficient [Volume 50, Issue 4, 2018, Pages 893-902]
Bazargan Harandi1, H. Performance Optimization of Multi-Effect Distillation-Thermal Vapor Compression Desalination Using Genetic Algorithm [Volume 50, Issue 2, 2018, Pages 399-412]
Behbahani-nejad, M. Numerical Simulation of Transient Compressible Flow in Natural Gas long Transmission Pipelines Using a Suitable Parallel Algorithm [Volume 50, Issue 4, 2018, Pages 785-798]
Broghany, M. Increasing the Frequency Band of Sound Absorption for Flat Multi-Layered Absorbers Consisting of Porous Material, Perforated Panel and Air-Gap [Volume 50, Issue 1, 2018, Pages 219-230]
C
Chakherlou, T.N. Comparison Between Composite Patches and Bolt Clamping Force to Repair an Edge Crack in Aluminum Alloy 2024-T3 Specimens [Volume 50, Issue 3, 2018, Pages 627-640]
Changizian, S. A Coupled Thermal Model for Refrigeration Cycle and Cabin of the First Produced Vehicle Based on the National Vehicle Platform [Volume 50, Issue 6, 2019, Pages 1159-1174]
D
Dabbagh, A. Wave Propagation in Embedded Temperature-dependent Functionally Graded Nano-plates Subjected to Nonlinear Thermal Loading According to a Nonlocal Four-variable Plate Theory [Volume 50, Issue 5, 2019, Pages 973-988]
Daroudi, A. Measurement of Strain by Digital Shearography with a New Algorithm of Phase Calculation [Volume 50, Issue 1, 2018, Pages 25-32]
Dastourani, H. Numerical Simulation of Drop Deformation and Breakup in an Electric Field [Volume 50, Issue 4, 2018, Pages 767-784]
Davaq, A. Nonlinear Free Vibration in Flexure Beams with an Intermediate Rigid Element and a Tip Mass [Volume 50, Issue 1, 2018, Pages 125-136]
Davarpanah, E. Numerical Simulation of a Piston-Type Wavemaker using Lattice-Boltzmann Method with Moving Nested Grids [Volume 50, Issue 4, 2018, Pages 799-812]
Davoodi, F. Evaluating the Effects of Individual Characteristics on Thermal Sensation in an Indoor Pool with Different Arrangements for Inlet Air Diffusers [Volume 50, Issue 6, 2019, Pages 1175-1184]
DEHVEDAR, M. Experimental Study of Freeing Stuck Pipe by Changing in Characterization and Additives of Mud Cake [Volume 50, Issue 4, 2018, Pages 863-872]
Dolati, F. Experimental Investigation of Flow and Heat Transfer in a Smooth Channel Affected by Vortex Generator with a Punched Hole [Volume 50, Issue 2, 2018, Pages 271-284]
Dolati, S. Numerical Investigation of the Effect of Plasma Actuator on the Film Cooling Effectiveness By Fan-Shaped Hole [Volume 50, Issue 6, 2019, Pages 1213-1228]
E
Ebrahimi, F. Nonlinear Dynamic Response Analysis of Carbon Fiber Reinforced Polymer Enhanced with Carbon Nanotubes on Elastic Foundations in Thermal Environments [Volume 50, Issue 1, 2018, Pages 73-90]
Ebrahimi, F. Wave Propagation in Embedded Temperature-dependent Functionally Graded Nano-plates Subjected to Nonlinear Thermal Loading According to a Nonlocal Four-variable Plate Theory [Volume 50, Issue 5, 2019, Pages 973-988]
Elyasi, M. An Analytical Model and Numerical Simulations to Predict Process Parameters in the Tube Bending Under Internal Fluid Pressure [Volume 50, Issue 3, 2018, Pages 447-466]
Eslami, J. Numerical Study on the Effect of Air Diffuser Angle on the Flow Field and Contaminant Dispersion in a Ventilated Room [Volume 50, Issue 4, 2018, Pages 873-882]
Eslami Majd, A. Numerical Simulation of Drop Deformation and Breakup in an Electric Field [Volume 50, Issue 4, 2018, Pages 767-784]
Esmaeilzare, A. Numerical Analysis and Optimization of Magnetic Flux Density in the Polishing Process with Magnetorheological Fluid [Volume 50, Issue 3, 2018, Pages 577-588]
Estajloo, M. Energy and Exergy Analyzes and Evaluation of Traditional Flatbread Bakeries [Volume 50, Issue 6, 2019, Pages 1389-1402]
F
Fanni, E. Designing a New Intelligent Image Processing Algorithm for Traffic Sign Detection and Recognition Based on Fuzzy Logic [Volume 50, Issue 1, 2018, Pages 207-218]
Farahani, M. Comparison of the Effects of Shot Blasting and Sandblasting Processes on the Strength of the Aluminum Adhesive Bonded Joints [Volume 50, Issue 5, 2019, Pages 1015-1022]
Farahani, M. Study on the Effects of Sanding on the Strength of the Adhesive Joints [Volume 50, Issue 3, 2018, Pages 619-626]
Farahat, S. Performance Optimization of an Irreversible Brayton Cycle, and Proposing New Definitions for Second Law Efficiency and Exergy [Volume 50, Issue 2, 2018, Pages 385-398]
Farjad Bastani, S. A Novel Algorithm for Automatic Parallel Parking a Car Based On Continuous-Curvature Clothoid Path Planning [Volume 50, Issue 5, 2019, Pages 1051-1060]
Farshchi Tabrizi, F. Thermodynamic Investigation of Cationic Surfactants Effect on Oil-Water Interfacial Tension [Volume 50, Issue 2, 2018, Pages 437-444]
Fathollahi, A.B. Theoretical and Numerical Study and Comparison of the Inertia Effects on the Collapse Behavior of Expanded metal tube Absorber with Single and Double Cell under Impact Loading [Volume 50, Issue 5, 2019, Pages 999-1014]
Fattahi, H. Investigation of Ultrasonic Assisted Electro Discharge Machining with TiO2, Al2O3 and ZnO Nano-Powder [Volume 50, Issue 3, 2018, Pages 541-550]
Fazelzadeh Haghighi, S. A. Flutter Analysis of Adaptive Wing with the Adjustment of Spar Position [Volume 50, Issue 1, 2018, Pages 197-206]
Fazilati, J. Dynamic Behavior Analysis of Moderately Thick Composite Laminated Plates Containing Square Delamination Using Spline-Finite Strip Method [Volume 50, Issue 1, 2018, Pages 63-72]
Fazilati, J. Free Vibration of, Functionally Graded Materials Cylindrical Shells on Elastic Foundation under Axial force, Lateral Pressure and Different Boundary Conditions [Volume 50, Issue 5, 2019, Pages 1097-1112]
Foadaddini, A. Evaluating the Effects of Individual Characteristics on Thermal Sensation in an Indoor Pool with Different Arrangements for Inlet Air Diffusers [Volume 50, Issue 6, 2019, Pages 1175-1184]
Fotouhi, A. Nonlinear Longitudinal Free Vibration of a Rod Undergoing Finite Strain [Volume 50, Issue 5, 2019, Pages 1085-1096]
G
Ghadami, A. Flutter Analysis of Adaptive Wing with the Adjustment of Spar Position [Volume 50, Issue 1, 2018, Pages 197-206]
Ghafarzade, M. Design and Construction of an Electronic Tiltmeter Calibrator and Estimation of Calibration Uncertainty [Volume 50, Issue 5, 2019, Pages 1113-1122]
Ghaffari, A. Design and Implementation of Intelligent Systems Detect the Driver’s Lack of Concentration [Volume 50, Issue 5, 2019, Pages 1145-1154]
Ghafoorian, M.M. Optimization of a Hybrid Multi-effect Desalination with Thermal Vapor Compression and Reverse Osmosis Desalination System Integrated to A Gas Turbine Cycle [Volume 50, Issue 6, 2019, Pages 1333-1350]
Ghajar, R. Analytical Calculation of Stress Intensity Factors for Unequal Cracks Emanating from a Circular Hole in an Infinite Plane [Volume 50, Issue 5, 2019, Pages 943-950]
Ghalambaz, M. Static and Dynamic Pull-in Instabilities Analysis of Partially Affected Clamped Nano Actuators: The Substrate Effect [Volume 50, Issue 5, 2019, Pages 1023-1038]
Ghalambaz, M. Natural Convection Heat Transfer Inside a Square Enclosure with a Flexible Fin [Volume 50, Issue 2, 2018, Pages 233-254]
Ghasemi, H. Investigation of Step Sweep-Forward Angle Effects on the Hydrodynamic Performance of a Planing hull [Volume 50, Issue 4, 2018, Pages 903-912]
Ghorbani, L. Imitating Sound Ankle Behavior with a Powered Below-Knee Prosthesis and Validation of its Mechanical Performance [Volume 50, Issue 5, 2019, Pages 1137-1144]
Golzari, S. Energy Simulation and Parametric Analysis of Water Cooled Photovoltaic/Thermal System [Volume 50, Issue 6, 2019, Pages 1361-1374]
Gorji, H. Numerical and Experimental Investigation of Effective Parameters on Formability of Al-St Two Layer Sheet Metals [Volume 50, Issue 3, 2018, Pages 517-528]
Gorji Bandpy, M. The Experimental Study of Effective Characteristics on Differential Pressure Value Setting of Quarter-turn Actuator in Gas Transportation Pipelines [Volume 50, Issue 4, 2018, Pages 837-848]
Goudarzi, M. Numerical Study on Laminar Flow Over a Cylinder and Its Rotating Controllers for Suppressing the Vortex Shedding [Volume 50, Issue 4, 2018, Pages 849-862]
H
Habibi, S. Nonlinear Dynamic Response Analysis of Carbon Fiber Reinforced Polymer Enhanced with Carbon Nanotubes on Elastic Foundations in Thermal Environments [Volume 50, Issue 1, 2018, Pages 73-90]
Habibnia, M. Investigation of Parameters on the Efficiency of the Fuel cell Based on the Principles of Sealing [Volume 50, Issue 2, 2018, Pages 425-436]
Hadi, A. Free Vibration of, Functionally Graded Materials Cylindrical Shells on Elastic Foundation under Axial force, Lateral Pressure and Different Boundary Conditions [Volume 50, Issue 5, 2019, Pages 1097-1112]
Hadipour, A. Experimental Analysis of Heat Transfer from Round Jet Impinging to Asymmetric Concave Surface [Volume 50, Issue 6, 2019, Pages 1229-1236]
Haghparast, A. Static and Dynamic Pull-in Instabilities Analysis of Partially Affected Clamped Nano Actuators: The Substrate Effect [Volume 50, Issue 5, 2019, Pages 1023-1038]
Hajighafoori Boukani, N. Numerical Investigation of Vortex-Induced Vibrations of an Elastically-Mounted Circular Cylinder beneath a Free Surface [Volume 50, Issue 4, 2018, Pages 727-740]
Hajimohamadi, M. Analytical Calculation of Stress Intensity Factors for Unequal Cracks Emanating from a Circular Hole in an Infinite Plane [Volume 50, Issue 5, 2019, Pages 943-950]
Hasanzadeh, H. Evaluating the Effects of Individual Characteristics on Thermal Sensation in an Indoor Pool with Different Arrangements for Inlet Air Diffusers [Volume 50, Issue 6, 2019, Pages 1175-1184]
Hashemi, J. An Experimental Comparison of Dimensional and Geometrical Tolerances in Milled Holes on AISI D2 Steel [Volume 50, Issue 3, 2018, Pages 671-680]
Hashemi, M. Finite Element Analysis of Vibration Behavior of Micro-Rotors Utilizing a Developed Strain Gradient-Based Beam Element [Volume 50, Issue 1, 2018, Pages 113-124]
Hatami, H. Theoretical and Numerical Study and Comparison of the Inertia Effects on the Collapse Behavior of Expanded metal tube Absorber with Single and Double Cell under Impact Loading [Volume 50, Issue 5, 2019, Pages 999-1014]
Hazeri-Mahmel, N. Numerical Study of Mixed Convection Heat Transfer in a Cavity Filled with NonNewtonian Nanofluids Utilizing Two-phase Mixture Model [Volume 50, Issue 6, 2019, Pages 1199-1212]
Heidaryb, H. Experimental Study in Drilling Composite Pipes Manufactured by Filament Winding Process Using Full Factorial Design Method [Volume 50, Issue 3, 2018, Pages 489-504]
Hemmat zadeh, M. Numerical Study of Overlay Welding Effects on Residual Stresses in Girth Welded Steel Pipes [Volume 50, Issue 3, 2018, Pages 479-488]
Hooshmand, M. Evaluating the Effects of Individual Characteristics on Thermal Sensation in an Indoor Pool with Different Arrangements for Inlet Air Diffusers [Volume 50, Issue 6, 2019, Pages 1175-1184]
Hosseinalipour, S.M. Numerical Investigation of Vortex-Induced Vibrations of an Elastically-Mounted Circular Cylinder beneath a Free Surface [Volume 50, Issue 4, 2018, Pages 727-740]
Hosseini, M. Using Green Function Method to Dynamic Analysis of Nanotubes Conveying Fluid Under Moving Load [Volume 50, Issue 1, 2018, Pages 137-150]
Hosseinipour, J. Fabrication of Bipolar Plates of the Fuel Cell from Stainless Steel 304 by Hot Metal Gas Forming Process [Volume 50, Issue 3, 2018, Pages 589-600]
Hosseinzadeh, M. An Analytical Model and Numerical Simulations to Predict Process Parameters in the Tube Bending Under Internal Fluid Pressure [Volume 50, Issue 3, 2018, Pages 447-466]
I
Imani, H. An Experimental Comparison of Dimensional and Geometrical Tolerances in Milled Holes on AISI D2 Steel [Volume 50, Issue 3, 2018, Pages 671-680]
J
Jafari Vardanjani, M. Shunting Effect in Resistance Spot Welded Joints of Aluminum Alloys [Volume 50, Issue 3, 2018, Pages 561-576]
Jahanian, O. Defining Start and Duration of Combustion in HCCI Engines using Mean-Value Method for Control Applications [Volume 50, Issue 6, 2019, Pages 1265-1276]
Jahannama, M.R. Numerical Simulation of Drop Deformation and Breakup in an Electric Field [Volume 50, Issue 4, 2018, Pages 767-784]
Jahanshahi Javaran, E. Performance Optimization of Multi-Effect Distillation-Thermal Vapor Compression Desalination Using Genetic Algorithm [Volume 50, Issue 2, 2018, Pages 399-412]
Jahanshahi Javaran, E. Design, Manufacturing and Performance Evaluation of a Fixed Focus Scheffler Concentrator in Kerman [Volume 50, Issue 6, 2019, Pages 1303-1318]
Jahromi, M. The Design of a New Rotary Flow Control Valve with a Pressure Compensator for a Turbojet Engine [Volume 50, Issue 2, 2018, Pages 413-424]
Jalali Mehrabad, R. Effects of Adding Gaseous Soot and Methane Incomplete Combustion Products on Detailed Chemical Kinetics Combustion of Methane and Pollutants [Volume 50, Issue 6, 2019, Pages 1277-1288]
Jalili, M. Nonlinear Longitudinal Free Vibration of a Rod Undergoing Finite Strain [Volume 50, Issue 5, 2019, Pages 1085-1096]
Jamesahar, E. Natural Convection Heat Transfer Inside a Square Enclosure with a Flexible Fin [Volume 50, Issue 2, 2018, Pages 233-254]
Jamshidi Aval, H. Fabrication of Bipolar Plates of the Fuel Cell from Stainless Steel 304 by Hot Metal Gas Forming Process [Volume 50, Issue 3, 2018, Pages 589-600]
K
Kabganian, M. Designing an Adaptive Control Algorithm for Amirkabir’s Laboratory Attitude Simulator of a Spacecraft [Volume 50, Issue 1, 2018, Pages 163-174]
Kalteh, M. Investigation of the Effect of Velocity Slip and Temperature Jump on the Heat Transfer of Nanofluid in a Microchannel Under Constant Heat Flux with Lattice Boltzmann Method [Volume 50, Issue 2, 2018, Pages 255-270]
Kamali E., A. Design and Construction of an Electronic Tiltmeter Calibrator and Estimation of Calibration Uncertainty [Volume 50, Issue 5, 2019, Pages 1113-1122]
Kamali Moghadam, R. Numerical Assessment of the Pulse Crossing Jet in Nozzle Fluidic Thrust Vectoring Using Unsteady Reynolds-Averaged Navier–Stokes Turbulence Approach [Volume 50, Issue 6, 2019, Pages 1185-1198]
Kavousi Sisi, M. Dynamic Analysis of Asynchronous Low-Velocity Impacts on Laminated Composite Plate [Volume 50, Issue 1, 2018, Pages 47-62]
Kazemi, A. An Analytical Investigation into Effects of Fracture Dispersion Coefficients and Thermal Conductivity on Geothermally Fractured Reservoirs [Volume 50, Issue 2, 2018, Pages 359-368]
Keshtkar, M.R. Numerical Study of Turbulence in Diesel Spray Combustion Using Large Eddy Simulation [Volume 50, Issue 4, 2018, Pages 823-836]
Keyhani, M.H. Proposing Immersed Boundary-Lattice Boltzmann-Lattice Spring Algorithm for Simulation of 2-D Deformable Plate in Steady Flow [Volume 50, Issue 4, 2018, Pages 683-696]
Khadayari, A. Design and Implementation of Intelligent Systems Detect the Driver’s Lack of Concentration [Volume 50, Issue 5, 2019, Pages 1145-1154]
Khadem, J. Study the Effects of Uniform Magnetic Fields and Pressures on the Concentration of Main Species of Methane Combustion [Volume 50, Issue 2, 2018, Pages 337-346]
Khajehzadeh, M. Experimental Investigation and Finite Difference Modeling of Cutting Tool Temperature Distribution During Ultrasonically Assisted Turning [Volume 50, Issue 3, 2018, Pages 657-670]
Khaleghi, H. Numerical Study of Turbulence in Diesel Spray Combustion Using Large Eddy Simulation [Volume 50, Issue 4, 2018, Pages 823-836]
Khalili Dehkordi, E. Numerical Study on Laminar Flow Over a Cylinder and Its Rotating Controllers for Suppressing the Vortex Shedding [Volume 50, Issue 4, 2018, Pages 849-862]
Khodabandeh, B. Imitation Learning of Complex Behaviors to Humanoid Robots using Evolutionary Optimization of Neural Network of Unit Pattern Generator [Volume 50, Issue 5, 2019, Pages 1123-1136]
Khodayari, A. Designing a New Intelligent Image Processing Algorithm for Traffic Sign Detection and Recognition Based on Fuzzy Logic [Volume 50, Issue 1, 2018, Pages 207-218]
Khodayari, A. A Novel Algorithm for Automatic Parallel Parking a Car Based On Continuous-Curvature Clothoid Path Planning [Volume 50, Issue 5, 2019, Pages 1051-1060]
Khoramdel, M. Numerical Study of Turbulence in Diesel Spray Combustion Using Large Eddy Simulation [Volume 50, Issue 4, 2018, Pages 823-836]
Khorshidian, M. Experimental Study of the New Design 2.5kW Dead-End H2 /O2 PEM Fuel Cell Stack with New Design to Improve Fuel Utilization [Volume 50, Issue 2, 2018, Pages 369-376]
M
Mafi, M. Tracer Kinetic Modeling and Derivation of Time Activity Curves in Positron Emission Tomography in order to Enhance Accuracy in Cancerous Regions Diagnosis [Volume 50, Issue 4, 2018, Pages 813-822]
Mahmoodi, M. The Design of a New Rotary Flow Control Valve with a Pressure Compensator for a Turbojet Engine [Volume 50, Issue 2, 2018, Pages 413-424]
Mahmoodi, M. The Experimental Study of Effective Characteristics on Differential Pressure Value Setting of Quarter-turn Actuator in Gas Transportation Pipelines [Volume 50, Issue 4, 2018, Pages 837-848]
Mahmoudabad, M.A. Investigation of the Effect of Longitudinal Distance Between Two Cars on Fuel Consumption and Drag Coefficient [Volume 50, Issue 4, 2018, Pages 893-902]
Majidi, H.R. Brittle Fracture in Key-hole Notched Polymer Specimens under Combined Compressive-shear Loading [Volume 50, Issue 5, 2019, Pages 927-942]
Maleki, H.N. Comparison Between Composite Patches and Bolt Clamping Force to Repair an Edge Crack in Aluminum Alloy 2024-T3 Specimens [Volume 50, Issue 3, 2018, Pages 627-640]
Maleki-Delarestaghi1, S. Experimental Investigation of the Forced Convection Heat Transfer of Nanofluids in Curved Tubes [Volume 50, Issue 2, 2018, Pages 347-358]
Marghoubkar, M. R. Tracer Kinetic Modeling and Derivation of Time Activity Curves in Positron Emission Tomography in order to Enhance Accuracy in Cancerous Regions Diagnosis [Volume 50, Issue 4, 2018, Pages 813-822]
Masoumi, A. Influence of Interface Morphology on the Bond Strength During the Reshaping Process of Al-Cu Bimetal Pipes [Volume 50, Issue 3, 2018, Pages 467-478]
Masroori Saadat, H. Experimental Investigation and Numerical Simulation of the Pressure Force on the Formation of Metallic Bipolar Plate in the Stamping Process [Volume 50, Issue 3, 2018, Pages 505-516]
Mazidi, A. Flutter Analysis of Adaptive Wing with the Adjustment of Spar Position [Volume 50, Issue 1, 2018, Pages 197-206]
Mehrjoy, N. Investigating the Effect of Radiation Scattering and Surface Emission on Combined Convection Heat Transfer in an Enclosure with Moving Insulation Surface [Volume 50, Issue 6, 2019, Pages 1289-1302]
M. Heidari, M. Analytical Solution of Heat Transfer in LaserIrradiated Skin Tissue with Surface Heat Convection Using Dual Phase Lag Model [Volume 50, Issue 2, 2018, Pages 285-294]
Mirbagheri, S.M.H. Multiphase Simulation of Aluminum A356 Metal Foam Formation Process by Lattice Boltzmann Method [Volume 50, Issue 4, 2018, Pages 741-754]
Mirzaee, M. Study on Effect of Boundary Conditions in Transient Dynamic Stress Analysis of Thick Cylindrical Shells under Internal Moving Pressure [Volume 50, Issue 5, 2019, Pages 951-960]
Moarefvand, P. Experimental Study of Freeing Stuck Pipe by Changing in Characterization and Additives of Mud Cake [Volume 50, Issue 4, 2018, Pages 863-872]
Moavenian, M. Nonlinear Free Vibration in Flexure Beams with an Intermediate Rigid Element and a Tip Mass [Volume 50, Issue 1, 2018, Pages 125-136]
Moeenfard, H. Nonlinear Free Vibration in Flexure Beams with an Intermediate Rigid Element and a Tip Mass [Volume 50, Issue 1, 2018, Pages 125-136]
Mohaddes Deylami, H. Numerical Investigation of Upstream Ramp Effects on the Cooling Performance by Cylindrical and Fan-Shaped Hole [Volume 50, Issue 4, 2018, Pages 883-892]
Mohaddes Deylami, H. Numerical Investigation of the Effect of Plasma Actuator on the Film Cooling Effectiveness By Fan-Shaped Hole [Volume 50, Issue 6, 2019, Pages 1213-1228]
Mohammadpourfard, M. Numerical Investigation of Non-Uniform Magnetic Fields Effects on Heat Transfer and Development of Melting- Solidification Processes in an Enclosure [Volume 50, Issue 6, 2019, Pages 1251-1264]
Moharrami, R. Measurement of Strain by Digital Shearography with a New Algorithm of Phase Calculation [Volume 50, Issue 1, 2018, Pages 25-32]
Moharrami, R. Stress Measurement on Carbon Steel Specimen by Consideration of Magnetic-Barkhausen-Noise [Volume 50, Issue 5, 2019, Pages 1079-1084]
Mohhades Deylami, H. Experimental Investigation of Flow and Heat Transfer in a Smooth Channel Affected by Vortex Generator with a Punched Hole [Volume 50, Issue 2, 2018, Pages 271-284]
Mojallal agh, S. The Design of a New Rotary Flow Control Valve with a Pressure Compensator for a Turbojet Engine [Volume 50, Issue 2, 2018, Pages 413-424]
Molaeimanesh, G. R. A Coupled Thermal Model for Refrigeration Cycle and Cabin of the First Produced Vehicle Based on the National Vehicle Platform [Volume 50, Issue 6, 2019, Pages 1159-1174]
Mollamahdi, M. Numerical Study of the Effects of Speed and Place of Ceiling Fans on Thermal Comfort and Reducing Energy in Office Buildings [Volume 50, Issue 2, 2018, Pages 309-326]
Mollamahdi, M. Natural Convection of Turbulent Al2O3-Water Nanofluid with Variable Properties in a Cavity with a Heat Source and Heat Sink on Vertical Walls [Volume 50, Issue 6, 2019, Pages 1237-1250]
Momenifar, M. Experimental Investigation and Numerical Simulation of the Pressure Force on the Formation of Metallic Bipolar Plate in the Stamping Process [Volume 50, Issue 3, 2018, Pages 505-516]
Monadjemi, A. Imitation Learning of Complex Behaviors to Humanoid Robots using Evolutionary Optimization of Neural Network of Unit Pattern Generator [Volume 50, Issue 5, 2019, Pages 1123-1136]
Moradi, B. Brain Trauma in Vehicle Side Crash; Developing a Computational Model for Diffuse Axonal and Subdural Hematoma Injuries [Volume 50, Issue 1, 2018, Pages 91-102]
Mortazavi, S. Two Dimensional Simulation of Film Boiling Heat Transfer in Complex Geometries Using Front Tracking Method [Volume 50, Issue 6, 2019, Pages 1319-1333]
Mortazavi, S.S. Three Dimensional Numerical Simulation of a Drop and Drop-to-Wall Interaction under Uniform Electric Field [Volume 50, Issue 4, 2018, Pages 755-766]
Moshayedi, H. Numerical Study of Overlay Welding Effects on Residual Stresses in Girth Welded Steel Pipes [Volume 50, Issue 3, 2018, Pages 479-488]
Mousavi, S. S. Numerical Investigation of Upstream Ramp Effects on the Cooling Performance by Cylindrical and Fan-Shaped Hole [Volume 50, Issue 4, 2018, Pages 883-892]
N
Nabipour, M. Designing an Adaptive Control Algorithm for Amirkabir’s Laboratory Attitude Simulator of a Spacecraft [Volume 50, Issue 1, 2018, Pages 163-174]
Naghashnejad, M. Numerical Investigation of Upstream Ramp Effects on the Cooling Performance by Cylindrical and Fan-Shaped Hole [Volume 50, Issue 4, 2018, Pages 883-892]
Namar, M.M. Defining Start and Duration of Combustion in HCCI Engines using Mean-Value Method for Control Applications [Volume 50, Issue 6, 2019, Pages 1265-1276]
Nami, H. Energy and Exergy Analysis of a Two-Stage Thermoelectric Used for Heating and Cooling [Volume 50, Issue 2, 2018, Pages 377-384]
Naserian, M. M. Performance Optimization of an Irreversible Brayton Cycle, and Proposing New Definitions for Second Law Efficiency and Exergy [Volume 50, Issue 2, 2018, Pages 385-398]
Nasiri, M. Analytical Solution of Heat Transfer in LaserIrradiated Skin Tissue with Surface Heat Convection Using Dual Phase Lag Model [Volume 50, Issue 2, 2018, Pages 285-294]
Nasiri, R. Experimental Investigation of Using Phase Change Materials in Heating System of a Solar Greenhouse [Volume 50, Issue 2, 2018, Pages 327-336]
Nasiri, R. Experimental Study of Charge of Paraffin Wax Along with Nanoparticles in an Eccentric Double Tube Heat Exchanger for Storing Energy in a Solar Water Heater [Volume 50, Issue 6, 2019, Pages 1403-1410]
Nazari, M. Proposing Immersed Boundary-Lattice Boltzmann-Lattice Spring Algorithm for Simulation of 2-D Deformable Plate in Steady Flow [Volume 50, Issue 4, 2018, Pages 683-696]
Nazari, M. Experimental Investigation of the Forced Convection Heat Transfer of Nanofluids in Curved Tubes [Volume 50, Issue 2, 2018, Pages 347-358]
Nazem Nezhad, R. Investigation of Torsional Static Behavior of Nano-rods Embedded in Elastic Medium Considering Surface Energy Effect [Volume 50, Issue 5, 2019, Pages 961-972]
Nemati, A. Energy and Exergy Analysis of a Two-Stage Thermoelectric Used for Heating and Cooling [Volume 50, Issue 2, 2018, Pages 377-384]
Nikandish, P. Thermal Analysis for Diesel Engine Exhaust Manifold with Regard to the Boiling Phenomenon and Compared with Experimental Results [Volume 50, Issue 4, 2018, Pages 711-726]
Nikseresht, S. Thermodynamic Investigation of Cationic Surfactants Effect on Oil-Water Interfacial Tension [Volume 50, Issue 2, 2018, Pages 437-444]
Noghrehabadi, A. Static and Dynamic Pull-in Instabilities Analysis of Partially Affected Clamped Nano Actuators: The Substrate Effect [Volume 50, Issue 5, 2019, Pages 1023-1038]
NoorPoor, A. Energy Simulation and Parametric Analysis of Water Cooled Photovoltaic/Thermal System [Volume 50, Issue 6, 2019, Pages 1361-1374]
Nosrati, K. New Design of Cross-flow Fluidized Bed Dryers [Volume 50, Issue 6, 2019, Pages 1351-1360]
Nourghasemi, H. Investigation of Step Sweep-Forward Angle Effects on the Hydrodynamic Performance of a Planing hull [Volume 50, Issue 4, 2018, Pages 903-912]
Nourouzi, S. Investigation of Parameters on the Efficiency of the Fuel cell Based on the Principles of Sealing [Volume 50, Issue 2, 2018, Pages 425-436]
O
Ovesy, H. Free Vibration of, Functionally Graded Materials Cylindrical Shells on Elastic Foundation under Axial force, Lateral Pressure and Different Boundary Conditions [Volume 50, Issue 5, 2019, Pages 1097-1112]
P
Pak, A. Investigation of Ultrasonic Assisted Electro Discharge Machining with TiO2, Al2O3 and ZnO Nano-Powder [Volume 50, Issue 3, 2018, Pages 541-550]
Payan, S. Minimization of Rate of Heat Transfer from Rectangular Cavities with Free Convection in Various Aspect Ratios for Finding Characteristics of an Array of Adiabatic Thin Fins by PSO Algorithm [Volume 50, Issue 2, 2018, Pages 295-308]
Pirkandi, J. The Design of a New Rotary Flow Control Valve with a Pressure Compensator for a Turbojet Engine [Volume 50, Issue 2, 2018, Pages 413-424]
R
Rabiei, N. Investigation of the Effect of Longitudinal Distance Between Two Cars on Fuel Consumption and Drag Coefficient [Volume 50, Issue 4, 2018, Pages 893-902]
Rad, M. Fabrication and Test of an Axial Wind Turbine with the Most Power During Absorbing Flow Kinetic Energy [Volume 50, Issue 4, 2018, Pages 913-923]
Rafeeyan, M. Free and Forced Whirling Analyses of Rotors with Multiple Unbalanced Discs Under Axial Force [Volume 50, Issue 1, 2018, Pages 175-188]
Rahgoshay, S. M. Experimental Study of the New Design 2.5kW Dead-End H2 /O2 PEM Fuel Cell Stack with New Design to Improve Fuel Utilization [Volume 50, Issue 2, 2018, Pages 369-376]
Rahimi, A. Numerical Analysis and Optimization of Magnetic Flux Density in the Polishing Process with Magnetorheological Fluid [Volume 50, Issue 3, 2018, Pages 577-588]
Rahimi-Esbo, M. Experimental Study of the New Design 2.5kW Dead-End H2 /O2 PEM Fuel Cell Stack with New Design to Improve Fuel Utilization [Volume 50, Issue 2, 2018, Pages 369-376]
Rahnama, M. Performance Optimization of Multi-Effect Distillation-Thermal Vapor Compression Desalination Using Genetic Algorithm [Volume 50, Issue 2, 2018, Pages 399-412]
Rahnama, M. Design, Manufacturing and Performance Evaluation of a Fixed Focus Scheffler Concentrator in Kerman [Volume 50, Issue 6, 2019, Pages 1303-1318]
Rajabi, R. Design and Construction of an Electronic Tiltmeter Calibrator and Estimation of Calibration Uncertainty [Volume 50, Issue 5, 2019, Pages 1113-1122]
Rajabiani, E. Numerical Simulation of a Piston-Type Wavemaker using Lattice-Boltzmann Method with Moving Nested Grids [Volume 50, Issue 4, 2018, Pages 799-812]
Rajabi Zargarabadi, M. Experimental Analysis of Heat Transfer from Round Jet Impinging to Asymmetric Concave Surface [Volume 50, Issue 6, 2019, Pages 1229-1236]
Ramezani, H. Study on Effect of Boundary Conditions in Transient Dynamic Stress Analysis of Thick Cylindrical Shells under Internal Moving Pressure [Volume 50, Issue 5, 2019, Pages 951-960]
Ranjbar, S.Faramarz Energy and Exergy Analysis of a Two-Stage Thermoelectric Used for Heating and Cooling [Volume 50, Issue 2, 2018, Pages 377-384]
RASTI, A. An Experimental Comparison of Dimensional and Geometrical Tolerances in Milled Holes on AISI D2 Steel [Volume 50, Issue 3, 2018, Pages 671-680]
Razavi, S. On the Free Vibration Analysis of a CNT-Reinforced Plate Bonded to a Magnetoelectroelastic Layer [Volume 50, Issue 1, 2018, Pages 15-24]
Razfar, M. Experimental Investigation and Finite Difference Modeling of Cutting Tool Temperature Distribution During Ultrasonically Assisted Turning [Volume 50, Issue 3, 2018, Pages 657-670]
Raznahan, H. Study the Effects of Uniform Magnetic Fields and Pressures on the Concentration of Main Species of Methane Combustion [Volume 50, Issue 2, 2018, Pages 337-346]
Rezaei, M. Numerical Analysis and Optimization of Magnetic Flux Density in the Polishing Process with Magnetorheological Fluid [Volume 50, Issue 3, 2018, Pages 577-588]
Rezaei Shahreza, A. Manufacturing a Single Ultrasonic Tool Set of Vibrational friction stir welding in Bending and Axial Modes [Volume 50, Issue 3, 2018, Pages 601-618]
Rezaie, M. Natural Convection of Turbulent Al2O3-Water Nanofluid with Variable Properties in a Cavity with a Heat Source and Heat Sink on Vertical Walls [Volume 50, Issue 6, 2019, Pages 1237-1250]
Rezazadeh, M. Analytical Solution of Heat Transfer in LaserIrradiated Skin Tissue with Surface Heat Convection Using Dual Phase Lag Model [Volume 50, Issue 2, 2018, Pages 285-294]
Riahi, M. Failure Analysis of a Gas Turbine Blade Made of Inconel 738LC Super Alloy [Volume 50, Issue 1, 2018, Pages 103-112]
Riahi, M. Experimental Study of Cryogenic Cooling Effect on Tool Wear and Power Consumption During Turning of AISI304 [Volume 50, Issue 3, 2018, Pages 641-657]
Riazi, M. Thermodynamic Investigation of Cationic Surfactants Effect on Oil-Water Interfacial Tension [Volume 50, Issue 2, 2018, Pages 437-444]
Rosta Abkenar, A. Experimental Investigation of Flow and Heat Transfer in a Smooth Channel Affected by Vortex Generator with a Punched Hole [Volume 50, Issue 2, 2018, Pages 271-284]
Rostami Dibavar, M. Numerical Investigation of Non-Uniform Magnetic Fields Effects on Heat Transfer and Development of Melting- Solidification Processes in an Enclosure [Volume 50, Issue 6, 2019, Pages 1251-1264]
S
Saadat, S. H. M. Experimental Study of the New Design 2.5kW Dead-End H2 /O2 PEM Fuel Cell Stack with New Design to Improve Fuel Utilization [Volume 50, Issue 2, 2018, Pages 369-376]
Saberi, F. F. Designing an Adaptive Control Algorithm for Amirkabir’s Laboratory Attitude Simulator of a Spacecraft [Volume 50, Issue 1, 2018, Pages 163-174]
Sabour, M. Natural Convection Heat Transfer Inside a Square Enclosure with a Flexible Fin [Volume 50, Issue 2, 2018, Pages 233-254]
Sadeghi, M. H. An Experimental Comparison of Dimensional and Geometrical Tolerances in Milled Holes on AISI D2 Steel [Volume 50, Issue 3, 2018, Pages 671-680]
Sadeghian, H. Imitating Sound Ankle Behavior with a Powered Below-Knee Prosthesis and Validation of its Mechanical Performance [Volume 50, Issue 5, 2019, Pages 1137-1144]
Sadighi, M. Dynamic Analysis of Asynchronous Low-Velocity Impacts on Laminated Composite Plate [Volume 50, Issue 1, 2018, Pages 47-62]
Sadripour, S. Energy and Exergy Analyzes and Evaluation of Traditional Flatbread Bakeries [Volume 50, Issue 6, 2019, Pages 1389-1402]
Sadripour, S. Numerical Study of the Effects of Speed and Place of Ceiling Fans on Thermal Comfort and Reducing Energy in Office Buildings [Volume 50, Issue 2, 2018, Pages 309-326]
Saeedi, A. Study the Effects of Uniform Magnetic Fields and Pressures on the Concentration of Main Species of Methane Combustion [Volume 50, Issue 2, 2018, Pages 337-346]
Saeedi, A. Effects of Adding Gaseous Soot and Methane Incomplete Combustion Products on Detailed Chemical Kinetics Combustion of Methane and Pollutants [Volume 50, Issue 6, 2019, Pages 1277-1288]
Safari, A. Comparison of the Effects of Shot Blasting and Sandblasting Processes on the Strength of the Aluminum Adhesive Bonded Joints [Volume 50, Issue 5, 2019, Pages 1015-1022]
Safari, A. Study on the Effects of Sanding on the Strength of the Adhesive Joints [Volume 50, Issue 3, 2018, Pages 619-626]
Saffar, S. Increasing the Frequency Band of Sound Absorption for Flat Multi-Layered Absorbers Consisting of Porous Material, Perforated Panel and Air-Gap [Volume 50, Issue 1, 2018, Pages 219-230]
Sahami poor Dehghan, M. Experimental Study in Drilling Composite Pipes Manufactured by Filament Winding Process Using Full Factorial Design Method [Volume 50, Issue 3, 2018, Pages 489-504]
Saidi, M. Numerical Study on the Effect of Air Diffuser Angle on the Flow Field and Contaminant Dispersion in a Ventilated Room [Volume 50, Issue 4, 2018, Pages 873-882]
Saidi, M. H. Numerical Study on the Effect of Air Diffuser Angle on the Flow Field and Contaminant Dispersion in a Ventilated Room [Volume 50, Issue 4, 2018, Pages 873-882]
Salimi, M.R. Phenomenological Study of Droplet Behavior Passing through a Porous Medium at Pore-Scale, Using Lattice Boltzmann Method [Volume 50, Issue 4, 2018, Pages 697-710]
Sarafraz, Y. Examination of Helicopter Dynamic Response Using Dynamic Inflow Model [Volume 50, Issue 1, 2018, Pages 189-196]
Sarhaddi, F. Performance Optimization of an Irreversible Brayton Cycle, and Proposing New Definitions for Second Law Efficiency and Exergy [Volume 50, Issue 2, 2018, Pages 385-398]
Sarhaddi, F. Performance Investigation of a Single Effect (LiBr-H2O) Absorption Cooling System connected to Photovoltaic Thermal Collectors [Volume 50, Issue 6, 2019, Pages 1375-1388]
Sattarifar, I. Buckling Analysis on Cylindrical Shell with Longitudinal and Circumferential Welds [Volume 50, Issue 3, 2018, Pages 551-560]
Sattari-Far, I. Numerical Study of Overlay Welding Effects on Residual Stresses in Girth Welded Steel Pipes [Volume 50, Issue 3, 2018, Pages 479-488]
Sayehbani, M. Investigation of Step Sweep-Forward Angle Effects on the Hydrodynamic Performance of a Planing hull [Volume 50, Issue 4, 2018, Pages 903-912]
Sedaghatkish, َA. Two Dimensional Simulation of Film Boiling Heat Transfer in Complex Geometries Using Front Tracking Method [Volume 50, Issue 6, 2019, Pages 1319-1333]
Sefidgar, M. Tracer Kinetic Modeling and Derivation of Time Activity Curves in Positron Emission Tomography in order to Enhance Accuracy in Cancerous Regions Diagnosis [Volume 50, Issue 4, 2018, Pages 813-822]
Sepehrnia, M. Natural Convection of Turbulent Al2O3-Water Nanofluid with Variable Properties in a Cavity with a Heat Source and Heat Sink on Vertical Walls [Volume 50, Issue 6, 2019, Pages 1237-1250]
Setoodeh, A. Bending and Free Vibration Analysis of Functionally Graded Nano-plate Using Trigonometric Higher-Order Plate Theory [Volume 50, Issue 5, 2019, Pages 1039-1050]
Seyedmonir, P. Buckling Analysis on Cylindrical Shell with Longitudinal and Circumferential Welds [Volume 50, Issue 3, 2018, Pages 551-560]
Seyyedi, S. E. Numerical and Experimental Investigation of Effective Parameters on Formability of Al-St Two Layer Sheet Metals [Volume 50, Issue 3, 2018, Pages 517-528]
Shahbazi, H. Design of a Nonlinear Controller on Quadrotor Drone Using Combined Method of Gradient Particle Swarm Optimization [Volume 50, Issue 5, 2019, Pages 989-998]
Shahbazi, H. Imitation Learning of Complex Behaviors to Humanoid Robots using Evolutionary Optimization of Neural Network of Unit Pattern Generator [Volume 50, Issue 5, 2019, Pages 1123-1136]
Shahhoseini, S. New Design of Cross-flow Fluidized Bed Dryers [Volume 50, Issue 6, 2019, Pages 1351-1360]
Shahi-Ashtiani, M. A. An Axiomatic Design Approach to Reduce Repetition in Tail Conceptual Design Process [Volume 50, Issue 1, 2018, Pages 3-14]
Shahin Varnoosfaderani, H. Three Dimensional Numerical Simulation of a Drop and Drop-to-Wall Interaction under Uniform Electric Field [Volume 50, Issue 4, 2018, Pages 755-766]
Shahmiri, F. Examination of Helicopter Dynamic Response Using Dynamic Inflow Model [Volume 50, Issue 1, 2018, Pages 189-196]
Shahryari Zanganeh, O. Performance Investigation of a Single Effect (LiBr-H2O) Absorption Cooling System connected to Photovoltaic Thermal Collectors [Volume 50, Issue 6, 2019, Pages 1375-1388]
Shakeri, A. Experimental Investigation of the Forced Convection Heat Transfer of Nanofluids in Curved Tubes [Volume 50, Issue 2, 2018, Pages 347-358]
Shakeri, M. Investigation of Parameters on the Efficiency of the Fuel cell Based on the Principles of Sealing [Volume 50, Issue 2, 2018, Pages 425-436]
Shakeri, M. Dynamic Analysis of Asynchronous Low-Velocity Impacts on Laminated Composite Plate [Volume 50, Issue 1, 2018, Pages 47-62]
Shakery, M. Buckling Analysis on Cylindrical Shell with Longitudinal and Circumferential Welds [Volume 50, Issue 3, 2018, Pages 551-560]
Shakhesi, S. Free Vibration of, Functionally Graded Materials Cylindrical Shells on Elastic Foundation under Axial force, Lateral Pressure and Different Boundary Conditions [Volume 50, Issue 5, 2019, Pages 1097-1112]
Shakib, S.E. Optimization of a Hybrid Multi-effect Desalination with Thermal Vapor Compression and Reverse Osmosis Desalination System Integrated to A Gas Turbine Cycle [Volume 50, Issue 6, 2019, Pages 1333-1350]
Shakoori, M. Energy Simulation and Parametric Analysis of Water Cooled Photovoltaic/Thermal System [Volume 50, Issue 6, 2019, Pages 1361-1374]
Sharifi, M. An Analytical Investigation into Effects of Fracture Dispersion Coefficients and Thermal Conductivity on Geothermally Fractured Reservoirs [Volume 50, Issue 2, 2018, Pages 359-368]
Sheikhzadeh, G. Investigation of the Wear Behavior of Graphite Steel (GSH48) in Ultrasonic Peening Process [Volume 50, Issue 3, 2018, Pages 529-540]
Sheikhzadeh, G. A. Natural Convection of Turbulent Al2O3-Water Nanofluid with Variable Properties in a Cavity with a Heat Source and Heat Sink on Vertical Walls [Volume 50, Issue 6, 2019, Pages 1237-1250]
Sheikhzadeh, G.A. Numerical Study of the Effects of Speed and Place of Ceiling Fans on Thermal Comfort and Reducing Energy in Office Buildings [Volume 50, Issue 2, 2018, Pages 309-326]
Shekari, Y. Numerical Study of Mixed Convection Heat Transfer in a Cavity Filled with NonNewtonian Nanofluids Utilizing Two-phase Mixture Model [Volume 50, Issue 6, 2019, Pages 1199-1212]
Shojaeefard, M. H. A Coupled Thermal Model for Refrigeration Cycle and Cabin of the First Produced Vehicle Based on the National Vehicle Platform [Volume 50, Issue 6, 2019, Pages 1159-1174]
Shokrani, P. Imitating Sound Ankle Behavior with a Powered Below-Knee Prosthesis and Validation of its Mechanical Performance [Volume 50, Issue 5, 2019, Pages 1137-1144]
Shooshtari, A. Stability Analyses and Dynamic Response of Fluid Conveyed Thin-Walled Piezoelectric Cylinder Under Harmonic Excitation [Volume 50, Issue 1, 2018, Pages 151-162]
Shooshtari, A. On the Free Vibration Analysis of a CNT-Reinforced Plate Bonded to a Magnetoelectroelastic Layer [Volume 50, Issue 1, 2018, Pages 15-24]
Soleimani, J. An Analytical Model and Numerical Simulations to Predict Process Parameters in the Tube Bending Under Internal Fluid Pressure [Volume 50, Issue 3, 2018, Pages 447-466]
Soleimani Roody, B. Nonlinear Longitudinal Free Vibration of a Rod Undergoing Finite Strain [Volume 50, Issue 5, 2019, Pages 1085-1096]
Soltani, M. Tracer Kinetic Modeling and Derivation of Time Activity Curves in Positron Emission Tomography in order to Enhance Accuracy in Cancerous Regions Diagnosis [Volume 50, Issue 4, 2018, Pages 813-822]
T
Taeibi Rahni, M. Phenomenological Study of Droplet Behavior Passing through a Porous Medium at Pore-Scale, Using Lattice Boltzmann Method [Volume 50, Issue 4, 2018, Pages 697-710]
Taghilu, M. J. Measurement of Strain by Digital Shearography with a New Algorithm of Phase Calculation [Volume 50, Issue 1, 2018, Pages 25-32]
Tajyar, A. Influence of Interface Morphology on the Bond Strength During the Reshaping Process of Al-Cu Bimetal Pipes [Volume 50, Issue 3, 2018, Pages 467-478]
Talebizadeh, M. A. Design, Manufacturing and Performance Evaluation of a Fixed Focus Scheffler Concentrator in Kerman [Volume 50, Issue 6, 2019, Pages 1303-1318]
Tarmigh, M. Numerical Simulation of Transient Compressible Flow in Natural Gas long Transmission Pipelines Using a Suitable Parallel Algorithm [Volume 50, Issue 4, 2018, Pages 785-798]
Tavakoli K., M. Design and Construction of an Electronic Tiltmeter Calibrator and Estimation of Calibration Uncertainty [Volume 50, Issue 5, 2019, Pages 1113-1122]
Tayebi, A. Numerical Study of Mixed Convection Heat Transfer in a Cavity Filled with NonNewtonian Nanofluids Utilizing Two-phase Mixture Model [Volume 50, Issue 6, 2019, Pages 1199-1212]
Tikani, V. Design of a Nonlinear Controller on Quadrotor Drone Using Combined Method of Gradient Particle Swarm Optimization [Volume 50, Issue 5, 2019, Pages 989-998]
Torabi, A.R. Brittle Fracture in Key-hole Notched Polymer Specimens under Combined Compressive-shear Loading [Volume 50, Issue 5, 2019, Pages 927-942]
Torabi, K. Thermo-Mechanical Stress Analysis in a Rotating Radially Graded FG-Disc with Non-Uniform Thickness [Volume 50, Issue 1, 2018, Pages 33-46]
Y
Yari, M. Energy and Exergy Analysis of a Two-Stage Thermoelectric Used for Heating and Cooling [Volume 50, Issue 2, 2018, Pages 377-384]
Yarmohammadi, A. A Coupled Thermal Model for Refrigeration Cycle and Cabin of the First Produced Vehicle Based on the National Vehicle Platform [Volume 50, Issue 6, 2019, Pages 1159-1174]
Yazdanparast, S. Numerical Study of Turbulence in Diesel Spray Combustion Using Large Eddy Simulation [Volume 50, Issue 4, 2018, Pages 823-836]
Yousefirad, S. Experimental Study of Freeing Stuck Pipe by Changing in Characterization and Additives of Mud Cake [Volume 50, Issue 4, 2018, Pages 863-872]
Z
Zahedi Nejad, Ali Fabrication and Test of an Axial Wind Turbine with the Most Power During Absorbing Flow Kinetic Energy [Volume 50, Issue 4, 2018, Pages 913-923]
Zamen, M. Energy Simulation and Parametric Analysis of Water Cooled Photovoltaic/Thermal System [Volume 50, Issue 6, 2019, Pages 1361-1374]
Zandi Baghche Maryam, A. Using Green Function Method to Dynamic Analysis of Nanotubes Conveying Fluid Under Moving Load [Volume 50, Issue 1, 2018, Pages 137-150]
Zeinolabedini, M. R. Free and Forced Whirling Analyses of Rotors with Multiple Unbalanced Discs Under Axial Force [Volume 50, Issue 1, 2018, Pages 175-188]
Ziaee, S. Free Vibration of Heterostructures of Graphene and Boron Nitride in Thermal Environment via Aifantis Theory with Velocity Gradients and Ritz Method [Volume 50, Issue 5, 2019, Pages 1061-1078]
Zoghi, T. New Design of Cross-flow Fluidized Bed Dryers [Volume 50, Issue 6, 2019, Pages 1351-1360]
Zolfaghari, S. A. Evaluating the Effects of Individual Characteristics on Thermal Sensation in an Indoor Pool with Different Arrangements for Inlet Air Diffusers [Volume 50, Issue 6, 2019, Pages 1175-1184]
